Installation Guide

6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A21MediumBasebulb150WMaximumor
(1)MediumBaseVintagebulbisrecommendedbutnotsupplied.
www.quoizel.com Care+Maintenance
LightSource:
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
EstimatedAssembly Time:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Mounting Screw
x3
F
Shade
x1
Assembly Instruction Sheet #IS-BRD9010MB
For Style BRD9010MB
B
Lock Ball
x2
C
Fixture
Hood
x1
D
Short Steel
Collar
x1
E
Long Steel
Collar
x1
G
Fixture
Body
x1
STEP 1 Install Bulb, Shade
and Fixture Hood
-
A. Place Shade (F) over the
Socket and secure with Long
Steel Collar (E). Hand tighten
until sung.
B. Thread the Short Steel Collar
(D) onto the Socket. Hand
tighten until sung.
C. Insert bulb into socket and
screw snugly into place.
D. Place the Fixture Hood (C)
over the Bolts on the top end
of the Fixture Body (G).
Secure by threading Lock
Balls (B) onto Bolts. Hand
tighten until sung.
Figure 1
B
C
D
E
F
G
Vintage Bulb
(recommended
but not supplied)
Socket
STEP 2 Drill Pilot Holes on Post-
A. Carefully fit the Post Fitter over the
end of the Post (not supplied),
making sure the Post Fitter is fully
seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference. After
marking hole locations, remove
fixture from post and drill 1/16” pilot
holes for screws.
Post
Post Fitter
Figure 2
Mounting Hole
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined
together. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
STEP 4 Attach Fixture Body to Post-
A. Coat the top 1” of the Post with Clear
Silicone Caulk (not supplied) and
position the Post Fitter onto the Post. Be
sure to seat it completely, aligning the
holes in the Fitter with the 1/16” Pilot
Holes drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled and
ready to use. Enjoy!
Post
Post Fitter
Figure 4
Mounting Hole
A
1of2
2016 QuoizelInc.
Thank you forpurchasing a Quoizelproduct.
Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2016-09-13
Bolt