Installation Guide

2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
2016 QuoizelInc.
RevisedDate:2016-05-06
Figure 4
REPLACE INNER SHADE
A. Unlock Finial and remove it from fixture.
. Unscrew Hex Nut and remove Flat Washer, Rubber Washer and
Diffuser.
B
Hex Nut and
Lock Washer
Mounting
Screw
D
A
Mounting
Ball
length of the nipple on the
Crossbar Assembly (A) by
unscrewing the preassembled
hex nut and lock washer and
then screwing the mounting
screws in or out of the crossbar
until the correct length is
achieved. Once the Ceiling
Canopy (D) is secure, remove
the mounting ball and Ceiling
Canopy (D) and proceed to
Step 5.
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 5
STEP 6 Install Fixture Body-
A. Carefully tuck all wires into the outlet
box and position the Ceiling Canopy (D)
over the outlet box. Align the holes in the
Ceiling Canopy (D) with the mounting
screws, then attach the Ceiling Canopy
(D) using the previously removed
mounting balls. Hand tighten until snug.
Mounting
Screw
D
A
Mounting
Ball
Figure 6
STEP 7 Install Bulb and Bottom Diffuser-
A. Thread the beaded end of the center Stem (F) into the coupling
underside of socket cluster. Hand tighten until snug.
B. This fixture uses standard bulb with medium screw base. Maximum
100 watts. Insert bulb and screw snugly into place.
F
I
H
K
G
L
Socket
Bulb
C. Place the Bottom Diffuser (I)
over the end of the Center
Stem (F), attach to Tabs
inside the bottom edge of
inner shade. Place Rubber
Washer (H) and Flat Washer
(G) over the end of the
Center Stem (F) and secure
with Hex Nut (K). Tighten
until snug gently.
D. Thread Finial (L) onto the
end of Center Stem (F) and
hand tighten until snug.
Your fixture is now
assembled and ready to
use. Enjoy!
Figure 7
Inner
Shade
Dffuseri
Fnalii
Flat Washer
Rubber Washer
Hex Nut
Stem
Lock
Screw
Outer
Shade
Lock
Ball
Figure 8
C. Hol
D. Reverse above steps to
reinstall rest components
to
d Lock Screw with
screwdriver, unlock Lock
Ball and replace the Inner
Shade with replacement
Inner Shade. Thread Lock
Balls back onto Lock
Screws and hand tighten
until snug to secure the
replacement Inner
Shade.
fixture.
BNY2816C
FINISH: POLISHED CHROME
(3) 100W
Bulbs
(Not Supplied)
Medium
Base
PART NUMBER
1
NO.
PART NUMBER
REPLACEMENT PART
QTY.
9006EXC
6”ROD
2
2
9012EXC
12” ROD
2
3
G2611DI
DIFFUSER 12"D
1
4
J1137DI
DIFFUSER 13.5"D
1
5
S12649FA
OUTER SHADE
1
6
S12768FA
INNER SHADE
1
5”Dia.
0.75”
45.5” OVERALL
HEIGHT INCLUDES
(2) 6” AND 12” RODS
10.75”Dia.
6”5.75”
13.25”Dia.
14”Dia.
16.25”Dia.
6.75”
NOTE: ALL DIMENSIONS ARE
ROUNDED UP TO THE
NEAREST 1/4"
1
2
3
4
5
6