Installation Guide

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2016 QuoizelInc.
Assembly Instruction Sheet #IS-BNY1716C
For Style BNY1716C
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)A19MediumBase100WbulbMaximum,Alternatebulb(3)23WCFLMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Released2016-04-26
Socket Assembly
x1
Package Contents
A
Crossbar Assembly
x1
B
4-3/8”L
Rod
x1
C
Ceiling
Canopy
x1
E
D
Center Stem
x1
F
I
Rubber
Washer
x1
Finial
x1
J
Diffuser
x1
STEP 1 - Install Ceiling Canopy,
Rod and Socket Assembly
together
A. Pass the supply wires and
ground wire through the Rod
(B) and the Ceiling Canopy
(C). Thread the Socket
Assembly (E), the Rod (B) and
the Ceiling Canopy (C)
together. Hand tighten until
sung.
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Figure 2
Hex Nut and
Lock Washer
Supply Wires with
Ground Wire
A
Outlet Box Screws
(not included)
Outlet Box
Mounting
Screw
C
A
Mounting
Ball
STEP 3 Fit Ceiling Canopy to
Crossbar Assembly
-
A.
Ceiling Canopy to the
Ceiling Canopy
ceiling
Remove mounting balls from the
Crossbar Assembly (A). Fit the
(C)
Crossbar Assembly (A) and
secure with mounting balls. Note:
The (C) should be
snug against the and the
Mounting balls. If not, adjust the
length of the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Ceiling Canopy (C) is secure, remove the
mounting ball and Ceiling Canopy (C) and proceed to Step 4.
Figure 3
Supply Wires
and Ground
Wire
Figure 1
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
C
E
STEP 5 Install Fixture
Body
-
A. Carefully tuck all wires into
the outlet box and position
the Ceiling Canopy (C) over
the outlet box. Align the
holes in the Ceiling Canopy
(C) with the mounting
screws, then attach the
Ceiling Canopy (C) using
the previously removed
mounting balls. Hand
tighten until snug.
Figure 5
Mounting
Screw
C
A
Mounting
Ball
G
Flat
Washer
x1
H
Hex Nut
x1
B
Thank you forpurchasing a Quoizelproduct.
Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184
or visit us on-line at www.quoizel.com