Installation Sheet

2of3
Figure 3
2018 QuoizelInc.
visit us on-line at www.quoizel.com
STEP 4A - Making the Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
Green Ground Screw
on the Crossbar
White wire
from outlet box
supply wire from fixture
identified with the Label “N”
Black wire from
outlet box (or Red)
supply wire from fixture
identified with the label “L”
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 4
Nipple
Fixture
Loop
Supply
Wires and
Ground Wire
Canopy
Chain Loop
Canopy
Lock Ring
C
B
D
C
Bulb(not
included)
Socket
STEP 5A - Install the
Glass Accents and
the Bulbs
a. Attach hooks on glass
accents to the loops on
support arms of the
fixture as shown in the
illustration.
b. Insert the bulb onto the
socket and screw
snugly into place.
Your fixture is now
assembled and ready
to use. Enjoy!
Assembly Instructions for Semi-flush Light
(Step1B-Step5B)
STEP 1B - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (G). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (G) with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
G
Figure 1
STEP 2B Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
Crossbar Assembly (A) and secure with
mounting balls. Note: The should be snug
against the and the mounting balls. If
Fixture canopy (F)
Fixture canopy (F)
not, adjust the length
of the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Fixture canopy (F) is secure, remove the
mounting ball and Fixture canopy (F) and proceed to Step 4B.
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
F
Figure 2
STEP 3B - Making the Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
Green Ground Screw
on the Crossbar
White wire
from outlet box
supply wire from fixture
identified with the Label “N”
Black wire from
outlet box (or Red)
supply wire from fixture
identified with the label “L”
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 3
D
B
A
ReleasedDate:2018-08-22