Other Content

D) Scratch removal process (step-by step):
E) Emergency and product information:
Clean and dry the area and now apply the base color and / or the
clear coat from the touch up pen to the scratch. It is best not to
use the thick brush on the touch up pen, but a thin, fine artist
brush size 0 or 1. Make sure that you only paint the scratch if at
all possible and not the surrounding areas.
Once the touch up paint has set completely (it is best to wait at
least a week), use the wet method to grind down any excess
clear coat residue around the filled and painted scratch. Proceed
with care and use a sheet of QUIXX sandpaper and some water.
Wet the 3000 grit sandpaper included in the repair kit. Gently
sand the damaged spot for a maximum of 15 seconds. Do not
attempt a 2nd sanding.
Polish the area with QUIXX REPAIR #1 and the included polishing
rag for about 2 minutes applying a lot of pressure. Do this at a
right angle to the scratch until all traces have vanished
completely.
Remove any REPAIR #1 residue using a moist rag and apply a
small amount of QUIXX FINISH Tube #2 to the scratch.
Now polish the area with QUIXX FINISH #2 and the second
enclosed polishing rag for about 2 minutes, applying a lot of
pressure. Use circular motions until the area has a glossy
appearance.
ATTENTION! Important additional information:
1.Never sand the same area for more than 15 seconds maximum. Failure to comply with this warning could result in the
removal of the entire clear coat or paint, which would leave behind stains.
2.The polishing pastes that are part of the QUIXX REPAIR system work better and more quickly if you apply more pressure
during the polishing process.
Remove any water and grinding residues and simply apply a small
amount of QUIXX REPAIR Tube #1 to the scratch.
D
Light Scratches
C
C
Regular Scratches
QUIXX POLISH No. 1
MSDS No. 888100004727
CONTAINS: Poly(oxy-1,2-ethanediyl), .alpha.-hydro-.omega.-hydroxy-
CAS# 25322-68-3; Aluminum oxide CAS# 68389-42-4
SPILL OR LEAK: Use mechanical handling equipment. Forms slippery/greasy layers with water.
QUIXX FINISH No. 2
MSDS No. 888100004728
CONTAINS: Water CAS# 7732-18-5; Aluminium silicate CAS# 12141-46-7; Polydimethylsiloxane-
emulsion; Ester of montanic acids CAS# 68476-04-0
SPILL OR LEAK: Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal
binder, sawdust). Forms slippery/greasy layers with water.
Not hazardous substances or preparations according to 16 CFR 1500.3.
FIRST AID GENERAL ADVICE: If used according to the instructions, no risks are expected for the user.
CALIFORNIA PROP. 65: This product does not contain any chemicals known to State of California to
cause cancer, birth, or any other reproductive defects.
HANDLING AND STORAGE: Keep out of reach of children. Keep away from food, drink and animal
feedingstuffs. For additional information read correlative Material Safety Data Sheet for these
products. In case of fire use suitable extinguishing media. This material is regulated by the Consumer
Saftey Protection Comission per the Federal Hazardous Substance Act (16 CFR 1500).
DISTRIBUTED BY:
WNV Sales Inc.
6100 Blue Lagoon Dr. - Suite 105
Miami, FL. 33126
Phone: [phone]
Fax: [phone]
E-mail:
EMERGENCY INFO: For 24-hour emergency assistance, call INFOTRAC at (352)-323-3500
E-mail: [e-mail]
1
POLISH
2
FINISH
2
4
5
6
7
3
1
A
+
B
Deep Scratches