Specification
!
C
C
C
O
O
O
N
N
N
C
C
C
R
R
R
E
E
E
T
T
T
E
E
E
B
B
B
O
O
O
N
N
N
D
D
D
I
I
I
N
N
N
G
G
G
A
A
A
D
D
D
H
H
H
E
E
E
S
S
S
I
I
I
V
V
V
E
E
E
P
P
P
R
R
R
O
O
O
D
D
D
U
U
U
C
C
C
T
T
T
N
N
N
O
O
O
.
.
.
9
9
9
9
9
9
0
0
0
1
1
1
,
,
,
9
9
9
9
9
9
0
0
0
2
2
2
PRODUCT USE
QUIKRETE® Concrete Bonding Adhesive is an exterior grade
synthetic emulsion that chemically adheres new concrete,
toppings and portland cement plaster or repair material to floors,
walls, sidewalks, silos, concrete pipes, concrete pavements,
concrete and cinder blocks, curbs and steps. It provides a
permanent chemical bond which is stronger than the material
being bonded. There is no need for chipping, drilling or roughing
the old surface before application.
SIZES
1 qt - No. 9901-14
1 gal – No. 9902-01
5 gal – No. 9902-05
COVERAGE
• As a paint-on adhesive - 35 - 75 ft
2
/qt (150 - 300 ft
2
/gal) (3.7 -
7.4 m
2
/L)
• As a slurry coat - approximately 19 ft
2
/qt (75 ft
2
/gal) (1.85 m
2
/L)
• As a primer - 300 - 600 ft
2
/gal (7.3 – 14.6 m
2
/L)
TECHNICAL DATA
APPLICABLE STANDARDS
ASTM International
• ASTM C1059 Standard Specification for Latex Agents for
Bonding Fresh to Hardened Concrete
• ASTM C1583 Standard Test Method for Tensile Strength of
Concrete Surfaces and the Bond Strength or Tensile Strength of
Concrete Repair and Overlay Materials by Direct Tension (Pull-off
Method)
Note - QUIKRETE Concrete Bonding Adhesive applied to
appropriate substrates will achieve tensile bond strengths typical
of those shown in Table 1. QUIKRETE Concrete Bonding
Adhesive meets or exceeds the requirements for ASTM C1059
Types I and II as shown in Table 2.
TABLE 1 - TYPICAL TENSILE BOND STRENGTHS TO
CONCRETE SUBSTRATES (ASTM C1583)
Application Tensile bond strength
Sand Mix bonded with 7 days 100 psi (0.7 MPa)
paint on adhesive 28 days 150 psi (1.0 MPa)
Sand Mix bonded with 7 days 300 psi (2.1 MPa)
a slurry coat 28 days 350 psi (2.4 MPa)
Primer for Fast-Setting 7 days 300 psi (2.1 MPa)
Self-Leveling Floor Resurfacer 28 days 400 psi (2.8 MPa)
TABLE 2 – SLANT SHEAR STRENGTHS (ASTM C1059)
Adhesive Type Specification
Type I > 400 psi (2.8 MPa)
Type II > 1,250 psi (8.6 MPa)
INSTALLATION
SURFACE PREPARATION
• Apply only to clean, sound surfaces
• Remove dust, dirt, oil, grease, wax, unsound concrete, plaster,
pain and other foreign materials.
APPLICATION
Use As a Paint-On Adhesive
• Apply to surface with brush, roller or spray to the thickness of a
coat of paint. Can be applied to a dry or damp surface
• Place new concrete, topping mixes, Portland cement, plaster
mixes or patches as soon as adhesive is dry. Gypsum plasters
and finish plaster should be placed over tacky coat of adhesive
!
DIVISION 3
PRODUCT DESCRIPTION
QUIKRETE® Concrete Bonding Adhesive is specifically formulated for permanently
bonding new concrete or plaster to old concrete or plaster. It is suitable for interior or
exterior applications. QUIKRETE® Concrete Bonding Adhesive is also used as the required
primer for QUIKRETE® Self-Leveling Floor Resurfacer.
!
!
!
Maintenance of Concrete
03 01 00
Hydraulic Cement
Underlayment
03 54 16
!