User Guide



O
O
O
N
N
N
E
E
E
C
C
C
O
O
O
A
A
A
T
T
T
F
F
F
I
I
I
B
B
B
E
E
E
R
R
R
G
G
G
L
L
L
A
A
A
S
S
S
S
S
S
R
R
R
E
E
E
I
I
I
N
N
N
F
F
F
O
O
O
R
R
R
C
C
C
E
E
E
D
D
D
S
S
S
T
T
T
U
U
U
C
C
C
C
C
C
O
O
O
P
P
P
R
R
R
O
O
O
D
D
D
U
U
U
C
C
C
T
T
T
N
N
N
O
O
O
.
.
.
1
1
1
2
2
2
0
0
0
0
0
0
(
(
(
S
S
S
A
A
A
N
N
N
D
D
D
E
E
E
D
D
D
)
)
)
A
A
A
N
N
N
D
D
D
N
N
N
O
O
O
.
.
.
1
1
1
2
2
2
1
1
1
6
6
6
(
(
(
C
C
C
O
O
O
N
N
N
C
C
C
E
E
E
N
N
N
T
T
T
R
R
R
A
A
A
T
T
T
E
E
E
D
D
D
)
)
)
PRODUCT DESCRIPTION
QUIKRETE

One Coat Fiberglass Reinforced Stucco is a fiber-
reinforced, Portland cement based plaster designed for use in one-
coat stucco applications. When applied in accordance with IAPMO
ER-455, this product provides a one-hour fire rating.

PRODUCT USE
QUIKRETER One Coat Fiberglass Reinforced Stucco (FRS) is an
alternative wall cladding. The system is a proprietary cementitious
mix for use as an exterior coating reinforced with wire fabric or lath. It
is applied to substrates of plywood, oriented strand board (OSB),
Gypsum sheathing or expanded polystyrene (EPS) extruded and
polyiso insulation board on exterior walls of wood or steel stud
construction. QUIKRETE One Coat Fiberglass Reinforced Stucco
may be applied over concrete and masonry units in one coat.
QUIKRETE FRS may also be used as the scratch and brown coat in
a conventional two or three coat stucco system.
QUIKRETE FRS has been evaluated by IAPMO as an exterior wall
covering in compliance with Chapters 15 and 25 of the IBC and
Chapter 7 of the IRC. Material has been evaluated for exterior
durability, wind resistance, fire-resistance ratings and installation on
walls required to be of Type I, II, III, IV and V construction. The
QUIKRETE FRS systems have been evaluated and are compliant
with the following codes and regulations:
 2015, 2012, 2009 and 2006 International Building Code
(IBC)
 2015, 2012, 2009 and 2006 International Residential Code
(IRC)
 2016 California Building Code (CBC) and 2016 California
Residential Code (CRC)
 2014 Florida Building Code (FBC), and 2014 Florida
Building Code Residential (FBC Residential)
QUIKRETE
®
One Coat FRS Sanded is a factory prepared mixture of
Type I or Type II Portland cement complying with ASTM C150,
hydrated lime complying with ASTM C207, fibers and other approved
ingredients. QUIKRETE
®
One Coat FRS Concentrated is the same
as QUIKRETE
®
One Coat FRS Sanded, except the concentrated mix
is provided for field addition of sand.
COVERAGE
QUIKRETE® One Coat One Coat Fiberglass Reinforced Stucco, per
80 lb (36.2 kg) bag:
3/8” (9.5 mm) 20-24 ft
2
(1.9-2.2 m
2
)
1/2” (13 mm) 15-18 ft
2
(1.4-1.7 m
2
)
3/4” (19 mm) 10-12 ft
2
(0.9-1.1 m
2
)
QUIKRETE® One Coat Fiberglass Reinforced Stucco Concentrated,
per 80 lb (36.2 kg) bag, blended with 210 pounds (95.3 Kg) of plaster
sand:
3/8” (9.5 mm) 73-87 ft
2
(6.8-8.1 m
2
)
1/2” (13 mm) 54-65 ft
2
(5.0-6.0 m
2
)
3/4” (19 mm) 36-44 ft
2
(3.3-4.1 m
2
)
All coverages are approximate and vary with thickness, waste, etc.
SIZES
• QUIKRETE
®
One Coat FRS is packaged in 80 lb (36.2 kg) bags
• QUIKRETE
®
One Coat FRS Concentrated is packaged in 80 lb
(36.2 Kg) bags and must be field mixed with properly graded plaster
sand in accordance with ASTM C897. Each 80 lb (36.2 Kg) bag
should be mixed with approximately 210 lb (95.2 Kg) of sand.
TECHNICAL DATA
Applicable Standards
ASTM International
• ASTM C150 Standard Specification for Portland Cement
• ASTM C207 Standard Specification for Hydrated Lime for Masonry
Purposes
• ASTM C834 Standard Specification for Latex Sealants
• ASTM C897 Standard Specification for Aggregate for Job-Mixed
Portland Cement-Based Plasters
• ASTM C926 Standard Specification for Application of Portland
Cement-Based Plaster
• ASTM C 1063 Standard Specification for Installation of Lathing and
Furring to Receive Interior and Exterior Portland Cement-Based
Plaster

Portland Cement
Plastering
09 24 00
DIVISION 9