ADVANCED WHOLE HOUSE FANS ® OWNER’S GUIDE RF WIRELESS CONTROL SEE // H E A R // F E E L THE QUIETCOOL DIFFERENCE 1 QUIETCOOLSYSTEMS.
GENERAL SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. Read Instructions - All safety and operation instructions must be read. Retain Instructions - The safety and operating instructions should be kept for future reference. Heed Warnings - All warnings should be followed. Follow Instructions - All installation and operating instructions should be followed. Water – The QuietCool system should not be used near water.
STOP! READ ALL INSTRUCTIONS IN THIS GUIDE BEFORE INSTALLING YOUR QUIETCOOL SYSTEM Read this guide before proceeding! The manufacturer is NOT responsible for faulty installation or product damages caused through failure to fully read this guide BEFORE attempting installation. FCC Regulations This device complies with Part 15 of the FCC Rules.
2. INSTALLATION TOOLS YOU WILL NEED - Phillips screwdriver - Power-drill - Philips bit 2-1 Installing the Hub IMPORTANT: If you are installing the Hub onto an existing QuietCool fan, be sure to shut off the power before attempting installation. If you are installing the Hub onto a new fan, perform all installation steps before plugging in the fan. Install the Hub directly to the motorhead: 1. Remove the handy box cover on your QuietCool fan.
Single Speed Wiring (for all 1500/1.5 models) (see Figure A) 1. Using a wire nut, connect the black wire from the power cord to the black wire from the Hub. 2. Connect the white wire from the power cord and the white wire on the fan to the white wire from the Hub. 3. Connect the black wire from the fan to the blue wire on the Hub 4. Cap the yellow and red wires from the Hub. 5. Ground the green wire from the fan and the green wire from the power cord to the ground screw in the Hub. 6.
Two Speed Wiring (for CL-2250 to 7000 and TRI PRO-2.5 to 7.0) (see Figure B) 1. Using a wire nut, connect the black wire from the power cord to the black wire from the Hub. 2. Connect the white wire from the power cord and the white wire on the fan to the white wire from the Hub. 3. Connect the black wire from the fan to the blue wire on the Hub 4. Connect the red wire from the fan to the red wire on the Hub 5. Cap the yellow wire from the Hub. 6.
Two Speed Wiring (for ES-2250 and STL PRO-2.5) (see Figure C) 1. Using a wire nut, connect the black wire from the power cord and the black wire from the fan to the black wire from the Hub. 2. Connect the white wire from the power cord and the white wire on the fan to the white wire from the Hub. 3. Connect the red wire from the fan to the red wire on the Hub 4. Connect the yellow wire from the fan to the blue wire on the Hub 5. Cap the yellow wire from the Hub. 6.
Two Speed Wiring (for ES-3100, 4700, 5400, 6000, 7000, and STL PRO-3.3) (see Figure D) 1. Using a wire nut, connect the black wire from the power cord and the black wire from the fan to the black wire from the Hub. 2. Connect the white wire from the power cord and the white wire on the fan to the white wire from the Hub. 3. Connect the red wire from the fan to the red wire on the Hub 4. Connect the blue wire from the fan to the blue wire on the Hub 5. Cap the yellow wire from the Hub. 6.
Three Speed Wiring (for STL PRO-4.8, 5.5, 6.0, & 7.0) (see Figure E) 1. Using a wire nut, connect the black wire from the power cord and the black wire from the fan to the black wire from the Hub. 2. Connect the white wire from the power cord and the white wire on the fan to the white wire from the Hub. 3. Connect the red wire from the fan to the red wire on the Hub 4. Connect the yellow wire from the fan to the yellow wire on the Hub 5.
2-3 Fan Hub LED Indicators Power Indicator • The Power LED indicator will always be lit when the Hub is connected to Power. • If this LED is not lit, check the power source Timer Indicator • The Timer LED indicator will light up as shown below: 1. 1 Hour: 1 Blink POWER TIMER TEST PAIR 2. 2 Hours: 2 Blinks 3. 4 Hours: 4 Blinks 4. 8 Hours: 8 Blinks 5. 12 Hours: 12 Blinks 6.
2-4 Pairing the Wall Switch 1. Using a flat-head screwdriver, remove the front cover off the wall switch. 2. Install the included AAA batteries into the switch. All the LED indicators will light up indicating that the switch has power. Replace the front cover. 3. Press and hold the Pair button on the Hub. The Pair LED indicator will be on for three seconds then turn off. This clears all previous pairings out of the Hub, 4. Press the Pair button on the Hub twice.
2-6 1. Installing the Wall Switch Using your hands, slide the Wall Switch off the mounting plate. 2. If you have an existing Wall Switch with a junction box installed, the mounting 1 2 4 8install 12 plate over the junction box using the oblong holes on the mounting plate. Make sure you install the mounting plate with the arrow facing upwards. H M 3. L If you do not have an existing junction box, simply install the mounting plate to the drywall.
Wall Switch Sleep Mode • If no button press is detected for 10 seconds, the Wall Switch will enter sleep mode. Pressing either button will wake the switch and display the current status. • In Sleep Mode, all LED indicators will be off. LED Status Indicators of Wall Switch • If all LED indicators on the Wall Switch come on after three seconds of pressing one of the buttons, this means the Wall Switch is failing to connect to the Hub.
Will my neighbor be able to control my fan if they have the same set up as me? They will not because you need to physically activate the pairing process between the RF Switch and the RF Hub. What is the range? The RF Switch and RF Hub have a range restriction of 100ft. What happens if I lose the RF Switch? If you lose or damage an RF Switch you will need to purchase another and re-pair the new one to the RF Hub. Can you control multiple fans with a single switch? No.
RF WIRELESS CONTROL LIMITED WARRANTY QC Manufacturing Inc. extends this warranty to the original purchaser of the following IT-RFHUB-01 and IT-RFSWITCH-01 - installed and used in a residence under normal conditions within the United States: A. One year coverage applies to the product. At our option we will repair or replace any part of the assembly should it fail to operate during the first year from the date of original purchase. B. This warranty does not cover any of the following: 1.
QuietCool is Proudly Designed and Built in California ADVANCED WHOLE HOUSE FANS 1-888-QUIETCOOL 43352 Business Park Drive, Temecula, CA 92590 ® // PH 951.325.6340 // QUIETCOOLSYSTEMS.
