OWNER’S GUIDE SMART ATTIC ROOF MOUNT FAN AFR SMT PRO-1.3 AFR SMT PRO-2.0 AFR SMT ES-2.0 ! DO NOT THROW AWAY! SERIAL NUMBER FOR FAN IS LOCATED ON THE BACK COVER OF THE OWNER’S GUIDE.
CONTENTS 1. SYSTEM OVERVIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3 System Venting Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GETTING STARTED - IMPORTANT - READ BEFORE INSTALL!. . . . . . 5 2. INSTALLATION. . . . . . . . . . . . .
1. SYSTEM OVERVIEW WELCOME 1.1 INTRODUCTION CONGRATULATIONS on the purchase of your new QuietCool Smart Attic Fan! INSTALLATION QuietCool Attic Fans are the best in the business.
1.3 SYSTEM VENTING REQUIREMENTS ! VERY IMPORTANT: 1 SQUARE FOOT OF NET FREE VENT AREA PER 750 CFM ! RECOMMENDED: 2 TO 4 SQUARE FEET OF INLET VENTS PER FAN Venting plays a very significant role in the performance of QuietCool fans. QuietCool recommends a minimum of 1 SQ. FT. of venting for every 750 CFM in the QuietCool system. If an attic has at least 1:750 attic venting, the QuietCool system will operate efficiently and effectively.
READ BEFORE ATTEMPTING TO INSTALL AN AFR FAN ! ! WELCOME GETTING STARTED NOTE: Always follow local building codes because the fan may require specific fasteners or anchoring systems not discussed in this installation guide. Installation should be done by a licensed roofing contractor. IMPORTANT: Do not cut through any rafters or structural members while cutting the fan hole. Only cut out the roof decking. GENERAL SAFETY INFORMATION INSTALLATION 1.
2. INSTALLATION 2.1 INSTALLING AFR (Shingle Roofs from 3:12 to 8:12) Installation Video: Watch the video by scanning the QR code or visit www.QuietCoolSystems.com/support Figure 2.1A ! NOTE: This installation utilizes the included Primary Flashing of the AFR. For installing the AFR on a tile or cement roof, please skip to page 8. 1. Determine in which area you would like to install your QuietCool AFR. 2.
Figure 2.1G WELCOME 10. Using a minimum of 8 roofing nails, nail the fan to the roof through the primary flashing, securing the fan to the roof. To prevent leaking, be sure to apply weatherproof sealant on the nail heads. (see Figure 2.1G) Figure 2.1H INSTALLATION 11. Secure the shingles by re-nailing them into the roof and applying weatherproof sealant. (See Figure 2.1H & I) 12. Apply weatherproof sealant to the seam between the AFR fan housing and primary flashing.
2.2 INSTALLING AFR (Tile or Cement Roofs from 3:12 to 8:12) ! ! Installation Video: Watch the video by scanning the QR code or visit www.QuietCoolSystems.com/support NOTE: This installation requires the purchase of the QuietCool Secondary Flashing accessory (part number FLA-SEC-3743) Figure 2.2A NOTE: When applying weatherproof sealant, be sure to use a generous amount to create a watertight seal. 1. Determine in which area you would like to install your QuietCool AFR. Figure 2.2B 2.
Figure 2.2G ! Figure 2.2H 13. Using the QuietCool Secondary Flashing accessory (part number FLA-SEC-3743), gently slide the flashing over the fan housing and hood mounting tabs. (see Figure 2.2H) ! ! Figure 2.2J NOTE: The secondary flashing was designed to work with almost all types of tile and cement roofs. The flashing can be molded to create the shapes of more unique style roofs such as S-Tile and M-Tile.
3. WIRING ! ! IMPORTANT: Wiring Diagrams are for examples ONLY. Wiring should be done by a licensed electrician following local building and electrical codes and/or NEC guidelines. NOTE: Your fan came with the Smart Control Hub pre-wired to a power cord for testing purposes before installation. If you would like to hard-wire the fan, or it is required by your local building codes, please follow the wiring instructions below. 3.1 TWO SPEED WIRING - (AFR SMT PRO-1.3 & AFR SMT PRO-2.0) 1.
WELCOME 3.2 THREE SPEED WIRING - (AFR SMT ES-2.0) 1. Using a wire nut, connect the black wire from the power cord and the black wire from the fan to the black wire from the Hub. 2. Connect the white wire from the power cord and the white wire on the fan to the white wire from the Hub. 3. Connect the red wire from the fan to the red wire on the Hub INSTALLATION 4. Connect the yellow wire from the fan to the yellow wire on the Hub 5. Connect the blue wire from the fan to the blue wire on the Hub 6.
3.3 SMART CONTROL HUB - LED INDICATORS 12 • POWER Indicator • The Power LED indicator will always be lit when the Hub is connected to Power. • If this LED is not lit, check the power source.
4. SYSTEM OPERATING INSTRUCTIONS DOWNLOADING THE QUIETCOOL SMART CONTROL APP WELCOME 4.1 Download the QuietCool Smart Control App onto your iOS or Android device. Scan the QR code above or visit QuietCoolSystems.com/smart-control/ and click the link to download the app to your device. INSTALLATION 4.2 OPERATING THE QUIETCOOL SMART CONTROL APP HOME PAGE This is the home page of the app and is presented as soon as the app is opened.
FAN CONTROL PAGE This page is accessed when you tap on your fan from the Home Page. On this page you can see the current conditions in your attic, activate the different modes of the fan, and get to the Fan Settings page. FAN SETTINGS PAGE This page is used to adjust the settings of the fan. You can quickly change the Fan Name, check if the speeds are set properly, change the Fan Model, enter the Serial Number and adjust the Climate Settings & Presets.
SETTING UP YOUR FAN WELCOME Once your attic fan has power, open up the QuietCool Smart Control app. You will be taken to the Home Page. You should see your attic fan show up in the list of available fans. A message indicates that setup is required. Press and hold the Pair button on the Hub until the LED indicator begins to blink. NOTE: You will need to initiate this Pairing process on each device you want to use to control your attic fan.
TEMPERATURE • The settings you choose in this section will change what temperature the fan will come on at each set speed. • Tap on any speed to adjust the temperature for each speed. HUMIDITY • Turn Fan Off: This is the humidity percentage that will cause the fan to turn off. For example, the factory setting is set at 90%, meaning the fan will turn off if the humidity in the attic is 90% or higher. Tap this setting if you would like to adjust the percentage.
WELCOME FAN CONTROL PAGE On the Fan Control page, you will see the current fan status, the current attic temperature, as well as the current attic humidity level. INSTALLATION You also have the option to Activate Smart Mode or Activate Timer Mode. You can also go into the Fan Settings page and adjust the settings that you setup in the first step. WIRING TIMER MODE Timer Mode is a simple way to turn your attic fan on for a set amount of time at a set speed.
SMART MODE Smart Mode will automatically change the speed based on the attic temperature and humidity. To activate Smart Mode, simply tap Activate Smart Mode. In Smart Mode, the first parameter that is checked is the Turn Fan Off humidity level. Regardless of the temperature in the attic, if the Humidity level in the attic is above the Turn Fan Off humidity setting, the fan will not turn on, or if it is already running, the fan will shut off.
WELCOME PAIR MODE INSTALLATION Pair Mode is a feature that was designed to prevent users from having to get into the attic to access the physical Hub in order to pair additional devices. ! NOTE: In order to use this feature, you must have one device that is already paired to the Fan Hub. If you do not have any devices that are currently paired to the Fan Hub, you will have to press the WIRING physical Pair button. In the Fan Settings page, tap Enter Pair Mode.
FIRMWARE UPDATE Your attic fan includes a Firmware Update feature in order for us to update your Fan Hub to include bug fixes and additional features in the future. We recommend checking for a new firmware update a few times per year. To check for an available firmware update, go into the Fan Settings page and tap Firmware Update. If there is no update available, an alert will popup indicating there is no available firmware update.
4.3 FREQUENTLY ASKED QUESTIONS WELCOME WHAT PROTOCOL DOES THIS CONTROL USE? This control operates over Bluetooth to connect to your phone. The control uses Wi-Fi for firmware updates. WILL MY NEIGHBOR BE ABLE TO CONTROL MY FAN IF THEY HAVE THE SAME SET UP AS ME? No. In order to connect to your Smart Attic Fan Control Hub, you must first pair your device by using the Pair button on the Hub.
ROOF MOUNT ATTIC FANS LIMITED WARRANTY This warranty is extended to the original purchaser of this model or, if this unit is purchased and requires installation by a building contractor, to the original owner of the home. No subsequent purchaser of the unit or of a home in which it is installed is entitled to any of the benefits of this warranty. The QuietCool Product that you have purchased has a limited warranty from the date of purchase against defects in workmanship and materials.
WELCOME ROOF MOUNT ATTIC FANS LIMITED WARRANTY Limited Warranty Protection Roof Mount Attic Fan - Controls INSTALLATION QC Manufacturing, Inc. extends this warranty coverage to the original purchaser of the following QuietCool products (see attached for applicable products) for a period of time (varies by product) provided that the product has been installed in strict accordance with QC Manufacturing, Inc.’s written installation instructions. Under this warranty, QC Manufacturing, Inc.
Rev. 8/30/23 FAN SERIAL NUMBER INFORMATION RETAIN FOR YOUR RECORDS. SERIAL NUMBER IS REQUIRED FOR WARRANTY PURPOSES. 1-888-QUIETCOOL | WWW.QUIETCOOLSYSTEMS.
