HUAWEI 1. Getting Started 2. Port 3. VLAN 4. Multicast 5. QoS/ACL 6. Integrated Management 7. STP 8. Security 9. Network Protocol 10. System Management 11. Remote Power-feeding 12. Appendix Quidway S3000-EI Series Ethernet Switches Command Manual VRP3.
Quidway S3000-EI Series Ethernet Switches Command Manual Manual Version T2-081929-20050625-C-1.04 Product Version VRP3.10 BOM 31190229 Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. If you purchase the products from the sales agent of Huawei Technologies Co., Ltd., please contact our sales agent. If you purchase the products from Huawei Technologies Co., Ltd.
Copyright © 2005 Huawei Technologies Co., Ltd. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.
About This Manual Release Notes The product version that corresponds to the manual is VRP3.10. Related Manuals The following manuals provide more information about the Quidway S3000-EI Series Ethernet Switches. Manual Content Quidway S3026C-PWR Ethernet Switch Installation Manual Introduces the system installation, booting, configuration and maintenance of S3026C-PWR Ethernet Switch.
This module introduces the commands used for configuring multicast protocols. z QoS/ACL This module introduces the commands used for configuring QoS/ACL. z Integrated Management This module introduces the commands used for integrated management. z STP This module introduces the commands used for configuring STP. z Security This module introduces the commands used for configuring 802.1X, AAA & RADIUS, and HABP.
I. General conventions Convention Description Arial Normal paragraphs are in Arial. Boldface Headings are in Boldface. Courier New Terminal Display is in Courier New. II. Command conventions Convention Description Boldface The keywords of a command line are in Boldface. italic Command arguments are in italic. [] Items (keywords or arguments) in square brackets [ ] are optional. { x | y | ... } Alternative items are grouped in braces and separated by vertical bars. One is selected.
IV. Keyboard operation Format Description Press the key with the key name inside angle brackets. For example, , , , or . Press the keys concurrently. For example, means the three keys should be pressed concurrently. Press the keys in turn. For example, means the two keys should be pressed in turn. V. Mouse operation Action Description Select Press and hold the primary mouse button (left mouse button by default).
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual Getting Started Huawei Technologies Proprietary
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 Logging in Switch Commands ................................................................................... 1-1 1.1 Logging in Switch Commands ........................................................................................... 1-1 1.1.1 authentication-mode................................................................................................ 1-1 1.1.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Table of Contents 2.1.2 display interface vlan-interface................................................................................ 2-1 2.1.3 display ip host.......................................................................................................... 2-2 2.1.4 display ip interface vlan-interface............................................................................ 2-3 2.1.5 display ip routing-table .........
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Chapter 1 Logging in Switch Commands 1.1 Logging in Switch Commands 1.1.1 authentication-mode Syntax authentication-mode { password | scheme | none } View User interface view Parameter password: Perform local password authentication. scheme: Perform local or remote authentication of username and password. none: Perform no authentication.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands undo auto-execute command View User interface view Parameter text: Specifies the command to be run automatically. Description Using auto-execute command command, you can configure to automatically run a specified command. When a user logs in, the command configured will be executed automatically. Using undo auto-execute command command, you can configure not to run the command automatically.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Parameter level: Specifies the command level, ranging from 0 to 3. view: Specifies the command view, which can be any of the views supported by the switch. command: Specifies the command to be configured. Description Using command-privilege level command, you can configure the priority of the specifically command of the specifically view.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Parameter 7: The data bits are 7. 8: The data bits are 8. Description Using databits command, you can configure the data bits for AUX (Console) port. Using undo databits command, you can restore the default bits of the AUX (Console). This command can only be performed in AUX user interface view. By default, the value is 8. Example # Configure the data bits of AUX (Console) port to 7 bits.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands 1.1.6 display user-interface Syntax display user-interface [ type number ] [ number ] View Any view Parameter type: Specifies the type of a user interface. number: Specifies the number of a user interface. Description Using display user-interface command, you can view the relational information of the user interface.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Field Description Modem Modem operation mode Privi Which levels of commands can be used after logging in from the user interface Auth User interface authentication method 1.1.7 display users Syntax display users [ all ] View Any view Parameter all: Display the information of all user interfaces.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands 1.1.8 flow-control Syntax flow-control { hardware | none | software } undo flow-control View User interface view Parameter hardware: Configures to perform hardware flow control. none: Configures no flow control. software: Configures to perform software flow control. Description Using flow-control command, you can configure the flow control mode on AUX (Console) port.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Description Using free user-interface command, you can reset a specified user interface. The user interface will be disconnected after the command is executed. Note that the current user interface cannot be cleared. Example # Reset user interface 1 after logged in to the switch via user interface 0.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands When the users log in the switch, if a connection is activated, the login header will be displayed. After the user successfully logs in the switch, the shell header will be displayed.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Please press ENTER %SHELL: (The initial character “%” is the header contents) Hello! Welcome 1.1.11 history-command max-size Syntax history-command max-size value undo history-command max-size View User interface view Parameter value: Defines the size of the history buffer, ranging from 0 to 256. By default, the size is 10, that is, 10 history commands can be saved.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Description Using idle-timeout command, you can configure the timeout function. If there is no user operation performed before idle-timeout expires, the user interface will be disconnected. Using undo idle-timeout command, you can restore the default idle-timeout. idle-timeout 0 means disabling idle-timeout. By default, idle-timeout is set to 10 minutes.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Parameter None Description Using lock command, you can lock the user interface to prevent unauthorized user from operating it. Example # Lock the current user interface. lock Password: xxxx Again: xxxx 1.1.15 parity Syntax parity { even | mark | none | odd | space } undo parity View User interface view Parameter even: Configures to perform even parity.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands 1.1.16 protocol inbound Syntax protocol inbound { all | ssh | telnet } View VTY user interface view Parameter all: Supports both Telnet and SSH protocols. ssh: Supports only SSH protocol. telnet: Supports only Telnet protocol. Description Using the protocol inbound command, you can configure the protocols supported by a designated user interface.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches z Chapter 1 Logging in Switch Commands VLAN view, Ethernet port view, and so on. For the related commands, see return, system-view. Example # Return to user view from system view. [Quidway] quit 1.1.18 return Syntax return View System view Parameter None Description Using return command, you can return to user view from a view other than user view.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Description Using screen-length command, you can configure how many lines that can be displayed on a screen of the terminal. Using undo screen-length command, you can restore the default number of terminal information lines displayed on the terminal screen. The screen-length 0 command is used to disable this function. Example # Configure the lines that can be displayed on a screen as 20 lines.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands View Local-user view Parameter ftp: Specifies user type as ftp. ftp-directory directory: Specifies the directory of ftp users, directory is a character string of up to 64 characters. lan-access: Specifies user type to lan-access, which mainly refers to Ethernet accessing users, 802.1x supplicants for example. ssh: Specifies user type as SSH. telnet: Specifies user type as Telnet.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands [Quidway-luser-zbr] service-type telnet level 0 # Quit the system and logs on with username “zbr” again. Now only the commands at level 0 are listed on the terminal.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Note: By default, password is required to be set for authenticating the users connecting via Modem or Telnet. If no password has been set, the following prompt will be displayed “Login password has not been set !” Example # Configure the local authentication password on VTY 0 to huawei. [Quidway-ui-vty0] set authentication password simple huawei 1.1.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Connection to host lost. 1.1.24 speed Syntax speed speed-value undo speed View User interface view Parameter speed-value: Specifies the transmission rate on the AUX (Console) port in bit/s, which can be 300, 600, 1200, 4800, 9600, 19200, 38400, 57600, 115200 or 4096000. The default rate is 9600bit/s.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands Using stopbits command, you can configure the stop bits on the AUX (Console) port. Using undo stopbits command, you can restore the default stop bits. This command can only be performed in AUX user interface view. By default, the value is 1. Example # Configure 2 stop bits on the AUX (Console) port. [Quidway-ui-aux0] stopbits 2 1.1.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands View System view Parameter level: User level, ranging from 1 to 3. The default value is 3, i.e. do not specify user level. It means the password to be set is used for entering level 3. simple: Configure to display the password in plain text. cipher: Configure to display the password in encrypted text. password: If the authentication is in the simple mode, the password must be in plain text.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands text: Specifies the hostname with a character string, ranging from 1 to 30 characters. The default name is Quidway. Description Using sysname command, you can configure the hostname of the switch. Using undo sysname command, you can restore the default hostname. Changing the hostname of the switch will affect the prompt of command line interface.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands User view Parameter hostname: Specifies the host name of the remote switch. It is configured using the ip host command. ip-address: Specifies the IP address of the remote switch. service-port: Designates the TCP port on the remote switch providing Telnet service, ranging from 0 to 65535.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 1 Logging in Switch Commands [Quidway] user-interface 0 5 [Quidway-ui0-5] 1.1.32 user privilege level Syntax user privilege level level undo user privilege level View User interface view Parameter level: Specifies which level of command a user can use after logon from the specifically user interface, ranging from 0 to 3.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Chapter 2 System IP Configuration Commands 2.1 System IP Configuration Commands 2.1.1 description Syntax description string undo description View VLAN interface view Parameter string: Description character string of management VLAN interface, ranges from 1 to 80 characters. The default character string is HUAWEI, Quidway Series, Vlan-interface1 Interface.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Description Using display interface vlan-interface command, you can view the related information about management VLAN interface such as physical status and link status of management VLAN interface, Ethernet frame format, MAC address, IP address and sub-net mask, description character string and MTU, etc. For the related command, see interface vlan-interface.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Parameter None Description Using display ip host command, you can view all the host names and their IP addresses. Example # Display all the host names and their IP addresses. display ip host Host Age Flags Address(es) My 0 static 1.1.1.1 Aa 0 static 2.2.2.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Vlan-interface1 current state : DOWN , Line protocol current state : DOWN Internet Address is 1.1.1.1/8 Primary Broadcast address : 1.255.255.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Routing Table: public net Destination/Mask Protocol Pre Cost Nexthop Interface 1.1.1.0/24 DIRECT 0 0 1.1.1.1 Vlan-interface1 1.1.1.1/32 DIRECT 0 0 127.0.0.1 InLoopBack0 127.0.0.0/8 DIRECT 0 0 127.0.0.1 InLoopBack0 127.0.0.1/32 DIRECT 0 0 127.0.0.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands The command is only applicable to display the route that passed basic ACL filtering rules. Example # Display the summary of active routes that are filtered through basic acl 2000. [Quidway] acl number 2000 [Quidway-acl-basic-2000] rule permit source 10.1.1.1 0.0.0.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Table 2-5 Description of information generated by the command display ip routing-table acl verbose Field Description Destination Destination address Mask Mask Protocol Routing protocol Preference Routing preference Nexthop Next hop address Interface Output interface, through which the data packet destined for the destination network segment is sent Vlinkindex Virtual link in
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Field Description Route state description: ActiveU The route is selected and is optimum Blackhole Blackhole route is similar to Reject route, but it will not send the ICMP unreachable message to the source end Delete The route is deleted Gateway Identifies that the route is not an interface route Hidden The route exists, but it is unavailable temporarily for some reasons (e.g.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Field Description Age Time to live Cost Value of the cost 2.1.7 display ip routing-table ip_address Syntax display ip routing-table ip_address [ mask ] [ longer-match ] [ verbose ] View Any view Parameter ip_address: Destination IP address. mask: IP address mask, length in dotted decimal notation or integer. It ranges from 0 to 32 when it is expressed with integer.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands # There is corresponding route in natural mask range. Display the summary. display ip routing-table 169.0.0.0 Routing Tables: Summary count:1 Destination/Mask Protocol Pre Cost Nexthop Interface 169.0.0.0/16 Static 2.1.1.1 LoopBack1 60 0 For detailed description of the output information, see Table 2-4.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands **Destination: 169.0.0.0 Protocol: #Static Mask: 255.0.0.0 Preference: -60 *NextHop: 2.1.1.1 Vlinkindex: 0 State: Age: 3:47 Cost: 0/0 For detailed description of the output information, see Table 2-5. 2.1.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands For detailed description of the output information, see Table 2-4. 2.1.9 display ip routing-table ip-prefix Syntax display ip routing-table ip-prefix ip-prefix-name [ verbose ] View Any view Parameter ip-prefix-name: ip prefix list name. verbose: With the parameter, this command displays the verbose information of both the active and inactive routes that passed filtering rules.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands **Destination: 10.1.1.0 Mask: 255.255.255.0 Protocol: #DIRECT Preference: 0 *NextHop: 10.1.1.2 Interface: 10.1.1.2(Vlan-interface1) Vlinkindex: 0 State: Age: 3:23:44 Cost: 0/0 **Destination: 10.1.1.2 Tag: 0 Mask: 255.255.255.255 Protocol: #DIRECT Preference: 0 *NextHop: 127.0.0.1 Interface: 127.0.0.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Summary count: 4 DIRECT Routing tables status:: Summary count: 3 Destination/Mask Protocol Pre Cost Nexthop Interface 20.1.1.1/32 DIRECT 0 0 127.0.0.1 InLoopBack0 127.0.0.0/8 DIRECT 0 0 127.0.0.1 InLoopBack0 127.0.0.1/32 DIRECT 0 0 127.0.0.1 InLoopBack0 Cost Nexthop Interface 0 127.0.0.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands +--8+--{127.0.0.0 +-32+--{127.0.0.1 Table 2-6 Description of information generated by the command display ip routing-table radix Field Description INET Address suite inodes Number of nodes routes Number of routes 2.1.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Table 2-7 Description of information generated by the command display ip routing-table statistics Field Description Proto Routing protocol route Number of routes active Number of active routes added Number of added routes after the router is rebooted or the routing table is cleared last time.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Destinations: 2 Holddown: 0 Chapter 2 System IP Configuration Commands Routes: 2 Delete: 0 **Destination: 127.0.0.0 Protocol: #DIRECT Hidden: 0 Mask: 255.0.0.0 Preference: 0 *NextHop: 127.0.0.1 Interface: 127.0.0.1(InLoopBack0) State: Age: 57:12 Cost: 0/0 **Destination: 127.0.0.1 Protocol: #DIRECT Mask: 255.255.255.255 Preference: 0 *NextHop: 127.0.0.1 Interface: 127.0.0.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Description Using interface vlan-interface command, you can create and enter management VLAN interface view. Using undo interface vlan-interface command, you can cancel management VLAN interface. Before creating and entering the management VLAN interface view, the corresponding VLAN specified by vlan-id must be created. Example # Enter the view of management VLAN interface 1.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands View System view Parameter hostname: Name of the host, a character string consisting of 1 to 20 characters, including letters, numbers or "_", and it must contain at least one letter. ip-address: Specifies the host IP address corresponding to the host name in dotted decimal notation. Description Using ip host command, you can configure the host name and corresponding IP address.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands gateway-address: Specifies the next hop IP address (in dotted decimal notation) of the route. preference-value: Specifies the preference of the route, ranging from 1 to 255. Description Using ip route-static command, you can configure a static route. Using undo ip route-static command, you can cancel the configured static route.
Command Manual - Getting Started Quidway S3000-EI Series Ethernet Switches Chapter 2 System IP Configuration Commands Example # Configure the default preference of static routes as 120. [Quidway] ip route-static default-preference 120 2.1.19 shutdown Syntax shutdown undo shutdown View VLAN interface view Parameter None Description Using shutdown command, you can disable the management VLAN interface. Using undo shutdown command, you can enable the management VLAN interface.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual Port Huawei Technologies Proprietary
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 Ethernet Port Configuration Commands................................................................... 1-1 1.1 Ethernet Port Configuration Commands............................................................................ 1-1 1.1.1 broadcast-suppression............................................................................................ 1-1 1.1.2 description .............................
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Chapter 1 Ethernet Port Configuration Commands 1.1 Ethernet Port Configuration Commands 1.1.1 broadcast-suppression Syntax broadcast-suppression ratio undo broadcast-suppression View Ethernet port view Parameter ratio: Specifies the maximum wire speed ratio of the broadcast traffic allowed on the port. The value ranges from 1 to 100. By default, the value is 100.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Parameter text: Port description character string, with 80 characters at most. Description Using description command, you can configure the description character string for Ethernet port. Using undo description command, you can cancel the port description character string. By default, the port description character string is null.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Ethernet0/12 current state : DOWN IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fc01-0101 The Maximum Transmit Unit is 1500 Media type is twisted pair, loopback not set Port hardware type is 100_BASE_TX 100Mbps-speed mode, full-duplex mode Link speed type is force link, link duplex type is force link Flow-control is enabled Value of flow-constrain is: 111 bps Proc
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Field Description Hardware address Port hardware address Description Port description character string The Maximum Transmit Unit Maximum transmit unit Media type Type of media loopback not set Port loopback test state Port hardware type Port hardware type 100Mbps-speed mode, full-duplex Both the duplex mode and the rate are set mode to auto-negotiation.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Field Description input(total): 0 packets, 0 bytes 0 broadcasts, 0 multicasts input(normal): - packets, - bytes - broadcasts, - multicasts input: 0 input errors, 0 runts, 0 giants, - throttles, 0 CRC 0 frame, - overruns, 0 aborts, 0 ignored, - parity errors Output(total): 0 packets, 0 bytes The statistics information of input/output 0 broadcasts, 0 multicasts, packets and errors on this
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Example # Display if the port loopback detection is enabled.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands 1.1.6 duplex Syntax duplex { auto | full | half } undo duplex View Ethernet port view Parameter auto: Port auto-negotiation attribute. full: Port full-duplex attribute. half: Port half-duplex attribute. Description Using duplex command, you can configure the full-duplex/half-duplex attribute of the Ethernet port.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands pps: Packets per second. Description Use the flow-constrain command to define traffic threshold on the port. Use the undo flow-constrain command to remove the traffic threshold configuration on the port. By default, no traffic threshold is defined on the port. After you define traffic threshold and handling pattern on the port, the system detects and counts the traffic in a specified interval.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Example # Configure the system to disable the port and send trap messages when actual traffic on the port exceeds the threshold. system-view System View: return to User View with Ctrl+Z. [Quidway] interface ethernet0/1 [Quidway-Ethernet0/1] flow-constrain method shutdown 1.1.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Parameter interval: Specifies time interval, ranging from 5 to 300 in seconds. The step is 5. The default value is 300. Description Using the flow-interval command, you can configure a time interval. When calculating port statistics information, the switch calculates the average port speed during the time interval. Using the undo flow-interval command, you can restore the default value.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Description Using interface command, you can enter the Ethernet port view. If the user wants to configure the related parameters of the Ethernet port, he must first use this command to enter the Ethernet port view. Example # Enter the Ethernet0/1 port view. [Quidway] interface ethernet0/1 1.1.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Description Using the command, you can enable loopback detection controlled function on Trunk and Hybrid port, that is, when the system finds out that ports on a certain VLAN on Trunk or Hybrid port is looped back, it then makes the Trunk and Hybrid port operate under control, meantime, deletes the port corresponding MAC address entry.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Example # Enable the port loopback detection. [Quidway] loopback-detection enable 1.1.15 loopback-detection interval-time Syntax loopback-detection interval-time time undo loopback-detection interval-time View System view Parameter time: Specifies the interval of monitoring external loopback conditions of the port. It ranges from 5 to 300, measured in seconds.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Description Using the loopback-detection per-vlan enable command, you can configure that the system performs loopback detection to all VLANs on Trunk and Hybrid ports. Using the undo loopback-detection per-vlan enable command, you can configure that the system only performs loopback detection to the default VLANs on the port.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands 1.1.18 port access vlan Syntax port access vlan vlan_id undo port access vlan View Ethernet port view Parameter vlan_id: VLAN ID defined in IEEE802.1Q, ranging from 2 to 4094. Description Using port access vlan command, you can join the access port to a specified VLAN. Using undo port access vlan command, you can cancel the access port from the VLAN.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Hybrid port can be configured together with the isolate-user-vlan. But if the default VLAN has set mapping in the isolate-user-vlan, the default VLAN ID cannot be modified. If you want to modify it, cancel the mapping first. The default VLAN ID of local hybrid port shall be consistent with that of the peer one, otherwise, the packet cannot be properly transmitted.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Example # Join hybrid port Ethernet0/1 to VLAN of 2, 4 and 50-100, and these VLAN will have tags. [Quidway-Ethernet0/1] port hybrid vlan 2 4 50 to 100 tagged 1.1.21 port link-type Syntax port link-type { access | hybrid | trunk } undo port link-type View Ethernet port view Parameter access: Configure the port as access port. hybrid: Configure the port as hybrid port.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands View Ethernet port view Parameter vlan_id_list: vlan_id_list = [ vlan_id1 [ to vlan_id2 ] ]&<1-10> is the VLAN range joined by the trunk port. It can be discrete. The vlan_id ranges from 2 to 4094. &<1-10> indicates that the former parameter can be input 10 times repeatedly at most. all: Join the trunk port to all VLANs.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Description Using port trunk pvid vlan command, you can configure the default VLAN ID of trunk port. Using undo port trunk pvid command, you can restore the default VLAN ID of the port. Trunk port and isolate-user-vlan cannot be configured simultaneously. The default VLAN ID of local trunk port should be consistent with that of the peer one, otherwise, the packet cannot be properly transmitted.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands 1.1.25 shutdown Syntax shutdown undo shutdown View Ethernet port view Parameter none Description Using shutdown command, you can disable the Ethernet port. Using undo shutdown command, you can enable the Ethernet port. By default, the Ethernet port is enabled. Example # Enable Ethernet port Ethernet0/1. [Quidway-Ethernet0/1] undo shutdown 1.1.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 1 Ethernet Port Configuration Commands Description Using speed command, you can configure the port speed. Using undo speed command, you can restore the default speed. By default, the speed is auto. For the related command, see duplex. Example # Configure Ethernet port Ethernet0/1 port speed as 10Mbps.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 2 Ethernet Port Link Aggregation Commands Chapter 2 Ethernet Port Link Aggregation Commands 2.1 Ethernet Port Link Aggregation Commands 2.1.1 display link-aggregation Syntax display link-aggregation [ master_port_num ] View Any view Parameter master_port_num: Master port number in an aggregation port group. Description Using display link-aggregation command, you can view the related information on aggregation port.
Command Manual - Port Quidway S3000-EI Series Ethernet Switches Chapter 2 Ethernet Port Link Aggregation Commands Field Description Other sub-ports Other member ports Mode Aggregation mode 2.1.2 link-aggregation Syntax link-aggregation port_num1 to port_num2 { both | ingress } undo link-aggregation { master_port_num | all } View System view Parameter port_num1: Starting range value of Ethernet port joined the Ethernet link aggregation.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual VLAN Huawei Technologies Proprietary
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 VLAN Configuration Commands................................................................................ 1-1 1.1 VLAN Configuration Commands........................................................................................ 1-1 1.1.1 description ............................................................................................................... 1-1 1.1.2 display vlan............
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 1 VLAN Configuration Commands Chapter 1 VLAN Configuration Commands 1.1 VLAN Configuration Commands 1.1.1 description Syntax description string undo description View VLAN view Parameter string: description character string of current VLAN, with a length ranging from 1 to 32 characters. The default description character string of current VLAN is VLAN ID of the VLAN, e.g. VLAN 0001.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 1 VLAN Configuration Commands static: Display information of VLAN created statically by the system. dynamic: Display information of VLAN created dynamically by the system. Description Using display vlan command, you can view related information about the specified or all VLANs. If vlan_id or all is specified, information of specified VLAN or all VLANs is displayed.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 1 VLAN Configuration Commands name. For their meanings and value range, read Parameter of “Port” in this document. The interface number after keyword to must be larger than or equal to the port number before to. &<1-10>: Representing the repeatable times of parameters, 1 is the minimal and 10 is the maximal. Description Using port command, you can add one port or one group of ports to VLAN.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 1 VLAN Configuration Commands [Quidway] vlan 1 [Quidway-vlan1] 1.1.5 vlan { enable | disable } Syntax vlan { enable | disable } View System view Parameter enable: Enable VLAN features of equipment. disable: Disable the VLAN features of equipment. Description Using vlan { enable | disable } command, you can enable/disable the VLAN features of equipment.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 2 Isolate-User-Vlan Configuration Commands Chapter 2 Isolate-User-Vlan Configuration Commands 2.1 isolate-user-vlan Configuration Commands 2.1.1 display isolate-user-vlan Syntax display isolate-user-vlan [ isolate-user-vlan_num ] View Any view Parameter isolate-user-vlan_num: VLAN ID of isolate-user-vlan, ranging from 1 to 4094.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 2 Isolate-User-Vlan Configuration Commands Vlan Type: static Private-vlan Type : Secondary Route Interface: not configured Description: VLAN 0004 Tagged Ports: none Untagged Ports: Ethernet0/4 Ethernet0/8 Vlan ID: 5 Vlan Type: static Private-vlan Type : Secondary Route Interface: not configured Description: VLAN 0005 Tagged Ports: none Untagged Ports: Ethernet0/4 Ethernet0/18 2.1.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 2 Isolate-User-Vlan Configuration Commands Secondary VLAN is established. The actual operation include: add the ports of isolate-user-vlan to every Secondary VLAN and add the ports of all Secondary VLANs to isolate-user-vlan. After undo command is run, the mapping relationship between isolate-user-vlan and Secondary VLAN will be canceled.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 2 Isolate-User-Vlan Configuration Commands 2.1.4 isolate-user-vlan igsp enable Syntax isolate-user-vlan igsp enable undo isolate-user-vlan igsp enable View VLAN view Parameter igsp: Enable IGSP ( IGMP Snooping Protocal ). Description Use the isolate-user-vlan igsp command to cause IGMP packets to be sent to the route interface with Secondary VLAN IDs.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 3 GARP/GVRP Configuration Commands Chapter 3 GARP/GVRP Configuration Commands 3.1 GARP Configuration Commands 3.1.1 display garp statistics Syntax display garp statistics [ interface interface_list ] View Any view Parameter interface_list: List of Ethernet port to be displayed, expressed as interface _list = { { interface_type interface_num | interface_name } [ to { interface_type interface_num | interface_name } ] }&<1-10>.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 3 GARP/GVRP Configuration Commands 3.1.2 display garp timer Syntax display garp timer [ interface interface_list ] View Any view Parameter interface_list: List of Ethernet port to be displayed, expressed as interface _list = { { interface_type interface_num | interface_name } [ to { interface_type interface_num | interface_name } ] }&<1-10>.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 3 GARP/GVRP Configuration Commands Parameter hold: GARP Hold timer. After received certain registration information, the GARP application entity will not send Join Message at once, instead, it starts the Hold timer. All the registration information received within duration of the Hold timer will be transmitted in the same frame after the Hold timer times out, thereby saving the bandwidth resource. join: GARP Join timer.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 3 GARP/GVRP Configuration Commands Parameter timer_value: Value of GARP leaveall timer in centisecond, ranging from 65 to 32765. The step is 5 centiseconds. The value of Leaveall timer should be greater than the value of Leave timer. By default, the value of LeaveAll timer is 1000 centiseconds, i.e. 10s. Description Using garp timer leaveall command, you can configure GARP leaveall timer.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 3 GARP/GVRP Configuration Commands command has no parameter, it will clear the GARP statistics information of all the ports. For the related command, see display garp statistics. Example # Clear GARP statistics information. reset garp statistics 3.2 GVRP Configuration Command 3.2.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 3 GARP/GVRP Configuration Commands 3.2.2 display gvrp status Syntax display gvrp status View Any view Parameter none Description Using display gvrp status command, you can view the global status information about GVRP. Example # Display the global status information about GVRP. display gvrp status GVRP is enabled 3.2.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 3 GARP/GVRP Configuration Commands For the related commands, see display gvrp status. Example # Enable global GVRP. [Quidway] gvrp 3.2.4 gvrp registration Syntax gvrp registration { fixed | forbidden | normal } undo gvrp registration View Ethernet port view Parameter fixed: Enable to create or register VLAN on the port manually and disable to register or deregister VLAN dynamically.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 4 Voice VLAN Configuration Commands Chapter 4 Voice VLAN Configuration Commands 4.1 Voice VLAN Configuration Commands 4.1.1 display voice vlan oui Syntax display voice vlan oui View Any view Parameter None Description Using the display voice vlan oui command, you can display the OUI address supported by the current system and its relative features. For related commands, see voice vlan vlan_id enable and voice vlan enable.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 4 Voice VLAN Configuration Commands Parameter None Description Using the display voice vlan status command, you can display the relative Voice VLAN features including the Voice VLAN status, the configuration mode, and the current Voice VLAN port status, and so on For related commands, see voice vlan vlan_id enable and voice vlan enable. Example # Enable the Voice VLAN on VLAN 2 and display the Voice VLAN status.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 4 Voice VLAN Configuration Commands For the related command, see display voice vlan status. Example # Set the aging time of Voice VLAN to 100 minutes. system-view System View: return to User View with Ctrl+Z. [Quidway] voice vlan aging 100 [Quidway] 4.1.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 4 Voice VLAN Configuration Commands undo voice vlan enable View System view Parameter vlan_id: The VLAN ID for the Voice VLAN to be enabled, in the range of 2 to 4094. Description Using the voice vlan command, you can globally enable the Voice VLAN features of one VLAN. Using the undo voice vlan enable command, you can globally disable its Voice VLAN features. A specified VLAN must exist for a successful Voice VLAN enabling.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 4 Voice VLAN Configuration Commands Parameter oui: The MAC address to be set, in the format of H-H-H. oui-mask: The valid length of a MAC address, represented by a mask, and in the format of H-H-H. string: Description of the MAC address, in the range of 1 to 30. Description Using the voice vlan mac-address command, you can set the MAC address that the Voice VLAN can control.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 4 Voice VLAN Configuration Commands View Ethernet port view Parameter None Description Using the voice vlan mode auto command, you can set the Voice VLAN in auto mode. Using the undo voice vlan mode auto command, you can set the Voice VLAN in manual mode. By default, the Voice VLAN is in auto mode.
Command Manual - VLAN Quidway S3000-EI Series Ethernet Switches Chapter 4 Voice VLAN Configuration Commands By default, the Voice VLAN security mode is enabled. If needed, the voice vlan security enable and undo voice vlan security enable commands must be executed before the Voice VLAN features are enabled globally. For the related command, see display voice vlan status. Example # Disable the Voice VLAN security mode. system-view System View: return to User View with Ctrl+Z.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual Multicast Huawei Technologies Proprietary
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 GMRP Configuration Commands............................................................................... 1-1 1.1 GMRP Configuration Commands ...................................................................................... 1-1 1.1.1 debugging gmrp ...................................................................................................... 1-1 1.1.2 display gmrp statistics ...
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 1 GMRP Configuration Commands Chapter 1 GMRP Configuration Commands 1.1 GMRP Configuration Commands 1.1.1 debugging gmrp Syntax debugging gmrp { event | packet } undo debugging gmrp { event | packet } View User view Parameter event: GMRP event. packet: GMRP packet. Description Using debugging gmrp command, you can enable GMRP debugging. Using undo debugging gmrp you can disable GMRP debugging.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 1 GMRP Configuration Commands View Any view Parameter interface interface-list: Specifies Ethernet port list, expressed as interface-list = { { interface_type interface_num | interface_name } [ to { interface_type interface_num | interface_name } ]}&<1-10>. For meanings and value ranges of interface-type, interface-number and interface-name, refer to the syntax description in the Port Configuration of this manual.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 1 GMRP Configuration Commands Example # Display the status of global GMRP. display gmrp status GMRP is enabled Table 1-2 Global GMRP status information Field Description GMRP is enabled GMRP is enabled globally. 1.1.4 gmrp Syntax gmrp undo gmrp View System view/Ethernet port view Parameter None Description Using gmrp command, you can enable global GMRP or enable GMRP on a port.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands Chapter 2 IGMP Snooping Configuration Commands 2.1 IGMP Snooping Configuration Commands 2.1.1 display igmp-snooping configuration Syntax display igmp-snooping configuration View Any view Parameter None Description Using display igmp-snooping configuration command, you can view the IGMP Snooping configuration information.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands 2.1.2 display igmp-snooping group Syntax display igmp-snooping group [ vlan vlanid ] View Any view Parameter vlan vlanid: Specifies the VLAN where the multicast group to be viewed is located. When the parameter is omitted, the command will display the information about all the multicast groups on the VLAN.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands 2.1.3 display igmp-snooping statistics Syntax display igmp-snooping statistics View Any view Parameter None Description Using display igmp-snooping statistics command, you can view the statistics information on IGMP Snooping. This command displays the statistics information about IGMP Snooping of Ethernet switch.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands Parameter interface_type: Port type. interface_number: Interface number. interface_name: Interface name, expressed as interface_name=interface_type interface_number. Description Use the display multicast-source-deny command to display configuration information about multicast source port checking.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands Example # Enable IGMP Snooping. [Quidway] igmp-snooping enable 2.1.6 igmp-snooping fast-leave Syntax igmp-snooping fast-leave undo igmp-snooping fast-leave View Ethernet port view Parameter None Description Using the igmp-snooping fast-leave command, you can enable the function of fast removing a port from a multicast group.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands View Ethernet port view Parameter limit: The maximum number of multicast groups on a port, in the range of 0 to 1000 . The default value is 1000. Description Using igmp-snooping group-limit command, you can set the maximum number of multicast groups permited on a port. Using undo igmp-snooping group-limit command, you can restore the default value.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands ACLs configured on the inbound port. If allowed, the switch then adds the port to the forward port list of the multicast group; otherwise, it drops the IGMP report packet and no data flow then will be sent to this port. Thus the switch can control users’ multicast program ordering. User-defined ACL rule is a multicast address or multicast address range (224.0.0.1 to 239.255.255.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands [Quidway] acl number 2001 [Quidway-acl-basic-2001] rule deny source 225.0.0.0 0.0.0.255 [Quidway-acl-basic-2001] rule permint source any z Create VLAN 2, and add Ethernet 0/2 to it. [Quidway] vlan 2 [Quidway-vlan2] port Ethernet 0/2 z Set the filtering of IGMP Snooping Report packets applied to ACL 2001 of VLAN 2 on Ethernet 0/2.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands undo igmp-snooping max-response-time View System view Parameter seconds: Maximum response time for a query ranging from 1 to 100 and measured in seconds; By default, 10. Description Using igmp-snooping max-response-time command, you can configure the maximum response time for a query. Using undo igmp-snooping max-response-time command, you can restore the default value.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches For the related Chapter 2 IGMP Snooping Configuration Commands command, see igmp-snooping, igmp-snooping max-response-time. Example # Set the aging time of the IGMP Snooping router port to 500 seconds. [Quidway] igmp-snooping router-aging-time 500 2.1.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 2 IGMP Snooping Configuration Commands # Enable multicast source port suppression on ports ethernet 0/1 to ethernet 0/10, and ethernet 0/12. [Quidway] multicast-source-deny interface ethernet 0/1 to ethernet 0/10 ethernet 0/12 2.1.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 3 Unknown Multicast Dropping Configuration Commands Chapter 3 Unknown Multicast Dropping Configuration Commands 3.1 Unknown Multicast Dropping Configuration Commands 3.1.1 unknown-multicast drop enable Syntax unknown-multicast drop enable undo unknown-multicast drop enable View System view Parameter None Description Using unknown-multicast drop enable command, you can enable the unknown multicast dropping function.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 4 Multicast MAC Address Configuration Commands Chapter 4 Multicast MAC Address Configuration Commands 4.1 Multicast MAC Address Configuration Commands 4.1.
Command Manual - Multicast Quidway S3000-EI Series Ethernet Switches Chapter 5 Multicast VLAN Configuration Commands Chapter 5 Multicast VLAN Configuration Commands 5.1 Multicast VLAN Configuration Commands 5.1.1 service-type multicast Syntax service-type multicast undo service-type multicast View VLAN view Parameter None Description Use the service-type multicast command to set the current VLAN to multicast VLAN. Use the undo service-type multicast command to cancel the setting.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual QoS/ACL Huawei Technologies Proprietary
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 ACL Commands........................................................................................................... 1-1 1.1 ACL Configuration Command List ..................................................................................... 1-1 1.1.1 acl............................................................................................................................ 1-1 1.1.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Table of Contents 3.1.3 snmp-agent community........................................................................................... 3-2 3.1.4 snmp-agent group ................................................................................................... 3-3 3.1.5 snmp-agent usm-user .............................................................................................
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands Chapter 1 ACL Commands 1.1 ACL Configuration Command List 1.1.1 acl Syntax acl { number acl-number | name acl-name [ advanced | basic | link | user ] } [ match-order { config | auto } ] undo acl { number acl-number | name acl-name | all } View System view Parameter number acl-number: Access list number, ranging from: 2000 to 2999: Basic ACL. 3000 to 3999: Advanced ACL. 4000 to 4999: L2 ACL.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands You can use the acl command to create an ACL and specify its name with “acl-name” and its type with the keywords “advanced”, ”basic”, ”link”, or "user”. For both numbered and named ACL, you can use the rule command to add rules for them after entering ACL view. (Use the quit command to exit ACL view.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands Description Using display acl config command, you can view the detail configuration information about the ACL, including all the statements and sequence numbers and how many packets and bytes matched these statements. The matched information is the information treated by switch’s CPU. The matched information of transmitted data can be displayed by display qos-global traffic-statistic command.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands Description Using display acl running-packet-filter all command, you can view the information about the running state of the ACL. The displayed information includes ACL name, rule name and running state. Example # Display the ACL running state on all the interfaces.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands from 08:30 2-5-2003 to 18:00 2-19-2003 Table 1-3 the display Information Field Current time is 4-3-2003 Thursday Description 14:36:36 Indicates the current time of the switch (according to the switch setting). Time-range: hhy ( Inactive ) Indicates the name of the time-range. “( Inactive )” indicates the status of this time-range is not active at current time.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands View System view Parameter user-group { acl-number | acl-name }: activate the user-defined ACL. acl-number: Specifies the ACL number, ranging from 5000 to 5999. acl-name: Specifies the ACL name with a character string started with English letters (that is [a to z, A to Z]), excluding space and quotation marks. ip-group { acl-number | acl-name }:activate the IP ACLs. IP ACLs include basic, advanced ACLs.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands acl-number: Specifies an access list with a number in the range of 2000 and 3999. acl-name: Specifies an access list with a character string, beginning with English letters [a-z, A-Z] only, excluding space and quotation marks, and not case sensitive. The all and any keywords are not allowed.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands undo rule rule-id [ destination | destination-port | dscp | fragment | icmp-type | precedence | source | source-port | time-range | tos ]* III.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands parameter takes ip, it means all the IP protocols. This parameter can be 1 ~ 255 if indicated by digit. source-addr wildcard | any: source-addr wildcard is the source IP address and source address wildcard, expressed in dotted decimal notation. any represents any source address.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands address wildcard of the data packets. These two parameters give the source MAC address range interested the users. For example, if source-mac-wildcard is specified as 0.0.ffff, it indicates that the user is interested in the first 32 bits (corresponding to the 0s in wildcard) of the source MAC address. interface { interface-name | interface-type interface-num } represents the L2 port receiving the packets.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands # Add a rule to a user-defined ACL. [Quidway-acl-user-5000] rule 1 permit 88 ff 18 1.1.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 1 ACL Commands Example # Configure a time range being effective since zero hour on January 1, 2000 and forever.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Chapter 2 QoS Commands 2.1 QoS Configuration Commands List 2.1.1 display qos cos-local-precedence-map Syntax display qos cos-local-precedence-map View Any view Parameter None Description Using display qos cos-local-precedence-map command, you can view “COS->Local-precedence” map. Example # Display “COS->Local -precedence” map.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Description Using display qos-global all command, you can view the settings of all the QoS parameters. This command is used for displaying the settings of all the QoS parameters, including priority tag, redirection, traffic statistics and traffic mirror. Example # Display the settings of all the QoS parameters.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Table 2-1 the display Information Field Description Indicates the traffic-priority configuration of the switch.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Parameter None Description Using display qos-global mirrored-to command, you can view the settings of the traffic mirror. This command is used for displaying the settings of traffic mirror. The information displayed includes the ACL of traffic to be mirrored and the observing port. For the related command, see mirrored-to. Example # Display the settings of traffic mirror.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Description Using display qos-global traffic-priority command, you can view the settings of traffic priority. This command is used for displaying the settings of traffic priority. The information displayed includes the ACL corresponding to the traffic tagged with priority, priority type and value. For the related command, see traffic-priority. Example # Display the settings of traffic priority.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Description Using display qos-global traffic-redirect command, you can view the settings of the redirection. This command is used for displaying the settings of the redirection. The information displayed includes the ACL corresponding to the traffic to be redirected, the destination port of redirection. For the related command, see traffic-redirect. Example # Display the settings of the redirection.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Description Using display qos-global traffic-statistic command, you can view the traffic statistics information. This command is used for displaying the traffic statistics information. The information displayed includes the ACL corresponding to the traffic to be counted and the number of packets counted.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Parameter interface-name | interface-type interface-num: Specifies a port of the switch. For detailed information, refer to the port command manual. Description Using display qos-interface all command, you can view the QoS setting of all the ports. If you do not input the port parameters, the command will display all the QoS settings on the switch, including traffic limit and line rate etc.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands 2.1.8 display qos-interface line-rate Syntax display qos-interface [ interface-name | interface-type interface-num ] line-rate View Any view Parameter interface-name | interface-type interface-num: Specifies a port of the switch. For detailed information, refer to the port command manual. Description Using display qos-interface line-rate command, you can view the settings of outgoing line rate on the port.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Any view Parameter interface-name | interface-type interface-num: Specifies a port of the switch. For detailed information, refer to the port command manual. Description Using display qos-interface traffic-limit command, you can view the settings of traffic limit. If you do not input the port parameters, the command will display the traffic limit settings on the switch.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands 2.1.10 display queue-scheduler Syntax display queue-scheduler View Any view Parameter None Description Using display queue-scheduler command, you can view the queue scheduling mode and parameters. For the related command, see queue-scheduler. Example # Display the queue scheduling mode and parameters.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands This command is used for configuring the general limitation of rate on the port for sending packets. Example # Limit the rate on port e0/1 to 10Mbps. [Quidway-Ethernet0/1] line-rate 10 2.1.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches interface-num and Chapter 2 QoS Commands interface-type specify a complete port name together. interface-name is interface-type added with interface-num. Description Using mirrored-to command, you can enable ACL traffic identification and perform traffic mirror. Using undo mirrored-to command, you can cancel traffic mirror. This command is used for mirroring the traffic matching the specified ACL (whose action is permit).
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Example # Set the priority of Ethernet0/1 port to 7. [Quidway-Ethernet0/1] priority 7 2.1.14 priority trust Syntax priority trust undo priority View Ethernet port view Parameter None Description Using priority trust command, you can configure system trusting the packet 802.1p priority and not replacing the 802.1p priorities carried by the packets with the port priority.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Parameter cos0-map-local-prec: Specifies the mapping value of “COS 0->local-prec”, which ranges from 0 to 7. cos1-map-local-prec: Specifies the mapping value of “COS 1->local-prec”, which ranges from 0 to 7. cos2-map-local-prec: Specifies the mapping value of “COS 2->local-prec”, which ranges from 0 to 7. cos3-map-local-prec: Specifies the mapping value of “COS 3->local-prec”, which ranges from 0 to 7.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Example # Configure “COS->Local-precedence” map. [Quidway] qos cos-local-precedence-map 0 1 2 3 4 5 6 7 After the configuration, the “COS->Local-precedence” map is shown in Table 1-6. Table 2-10 “COS->Local-precedence” map COS Value Local Precedence 0 0 1 1 2 2 3 3 4 4 5 5 6 6 7 7 2.1.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands weight of the queue 2. queue3-weight: Specifies the weight of the queue 3. queue4-weight: Specifies the weight of the queue 4. maxdelay: Specifies the maximum delay, ranging from 1 to 255, unit is 16ms. The packets in the highest-priority queue will be transmitted directly when the maximum delay expires. Description Using queue-scheduler command, you can configure the queue scheduler and the related parameters.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands ACL, ranging from 0 to 127. If you do not set this parameter, all the rules will be considered. link-group { acl-number | acl-name } [ rule rule ]: Specifies a Layer-2 ACL. acl-number: Specifies the ACL sequence number, ranging from 4000 to 4999, acl-name: Specifies the ACL name with a character string starting with English letters ([a-z, A-Z]) and excluding space and quotation mark.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Parameter inbound: Configures to limit the rate of traffic received via the interface. user-group { acl-number | acl-name } [ rule rule ]: Specifies a user-defined ACL. acl-number: Specifies the ACL sequence number, ranging from 5000 to 5999. acl-name: Specifies the ACL name with a character string starting with English letters ([a-z, A-Z]) and excluding space and quotation mark.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands 2.1.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands Description Using traffic-priority command, you can activate ACL and tag the traffic priority (whose action is permit). Using undo traffic-priority command, you can cancel the traffic priority settings. It can mark three priorities (dscp/IP preference, and cos) for the packets. The switch can put the packets into egress queue according to the cos value (namely the 802.1p preference) or local preference. If both 802.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands link-group { acl-number | acl-name } [ rule rule ]: Specifies a Layer-2 ACL. acl-number: Specifies the ACL sequence number, ranging from 4000 to 4999, acl-name: Specifies the ACL name with a character string starting with English letters ([a-z, A-Z]) and excluding space and quotation mark. rule rule: Specifies a rule of an ACL, ranging from 0 to 127. If you do not set this parameter, all the rules will be considered.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 2 QoS Commands ACL, ranging from 0 to 127. If you do not set this parameter, all the rules will be considered. ip-group { acl-number | acl-name } [ rule rule ]: Specifies a basic or advanced ACL. acl-number: Specifies the ACL sequence number, ranging from 2000 to 3999. acl-name: Specifies the ACL name with a character string starting with English letters ([a-z, A-Z]) and excluding space and quotation mark.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 3 Logon user’s ACL control command Chapter 3 Logon user’s ACL control command 3.1 Logon user’s ACL control command 3.1.1 acl Syntax acl acl-number { inbound | outbound } View User-interface view Parameter acl-number: Specifies an ACL with a number in the range of 2000 to 3999. inbound: Perform ACL control over the users that telnet to the local switch.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 3 Logon user’s ACL control command Parameter acl-number: Specifies a basic ACL with a number in the range of 2000 to 2999. Description Using ip http acl command, you can call an ACL and perform ACL control over the WEB network management users. Using undo ip http acl command, you can cancel the ACL control over the WEB network management users. This command calls numbered basic ACL only.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 3 Logon user’s ACL control command Example # Configures huawei as the community name, allows read-only access to the switch by the name, meanwhile, performs the ACL control to the network management user by ACL 2020. (Suppose ACL 2020 has been defined.) [Quidway] snmp-agent community read huawei acl 2020 3.1.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 3 Logon user’s ACL control command Description Using snmp-agent group command, you can configure a new SNMP group, and perform the ACL control to the group through the parameter acl acl-number. Using undo snmp-agent group command, you can cancel the SNMP group. Example # Creates a new SNMP group: huawei, and perform the ACL control to the group through ACL 2021. (Suppose ACL 2021 has been defined.
Command Manual - QoS/ACL Quidway S3000-EI Series Ethernet Switches Chapter 3 Logon user’s ACL control command privpassword: Specify the encryption password with a character string, ranging from 1 to 64 bytes. acl acl-number: the number of basic ACL, ranging from 2000 to 2999. local: Local entity user. engineid: Specify the related engine ID of the user.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual Integrated Management Huawei Technologies Proprietary
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 Stack Function Configuration Commands................................................................ 1-1 1.1 Stack Function Configuration Commands ......................................................................... 1-1 1.1.1 display stacking ....................................................................................................... 1-1 1.1.2 stacking ...........
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Table of Contents 2.3.15 logging-host......................................................................................................... 2-27 2.3.16 port-tagged .......................................................................................................... 2-28 2.3.17 reboot member .................................................................................................... 2-29 2.3.18 snmp-host.......
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 1 Stack Function Configuration Commands Chapter 1 Stack Function Configuration Commands 1.1 Stack Function Configuration Commands 1.1.1 display stacking Syntax display stacking [ members ] View Any view Parameter members: Display stack member information. It is omitted for the slave switches.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 1 Stack Function Configuration Commands MAC Address:00e0-fc07-0bc0 Member status: Admin IP: 172.31.0.1/16 Member number: 1 Name:stack_1.Quidway Device:Quidway S3026c MAC Address:00e0-fc07-58a0 Member status:Up IP: 172.31.0.2/16 Table 1-1 Display information Field Description Member number: 0 The number of member switch, main device’s number is 0 Name:stack_0.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 1 Stack Function Configuration Commands Example # Switch from master switch Quidway to slave Switch1, perform the configuration on Switch1 and then switch back to the master switch. stacking 1 quit 1.1.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 1 Stack Function Configuration Commands View System view Parameter from-ip-address: Starting address of the stack IP address pool. ip-address-number: Number of IP address in the stack IP addresses pool. ip-mask: Mask of the stack IP address. Description Using stacking ip-pool command, you can configure the optional IP address range in public network for a stack.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Chapter 2 HGMP V2 Configuration Commands 2.1 NDP Configuration Commands 2.1.1 display ndp Syntax display ndp [ interface port-list ] View Any view Parameter interface port-list: Specifies a list of ports isolated from the specified port. A list may contain consecutive or separated ports, or the combination of consecutive and separated ports.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Status: Enabled, Pkts Snd: 0, Pkts Rvd: 0, Pkts Err: 0 Interface: Ethernet0/5 Status: Enabled, Pkts Snd: 0, Pkts Rvd: 0, Pkts Err: 0 Interface: Ethernet0/6 Status: Enabled, Pkts Snd: 0, Pkts Rvd: 0, Pkts Err: 0 Interface: Ethernet0/7 Status: Enabled, Pkts Snd: 0, Pkts Rvd: 0, Pkts Err: 0 Interface: Ethernet0/8 Status: Enabled, Pkts Snd: 0, Pkts Rvd: 0, Pkts Err: 0 Interface: Ether
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Interface: Ethernet0/19 Status: Enabled, Pkts Snd: 0, Pkts Rvd: 0, Pkts Err: 0 Interface: Ethernet0/20 Status: Enabled, Pkts Snd: 0, Pkts Rvd: 0, Pkts Err: 0 Interface: Ethernet0/21 Status: Enabled, Pkts Snd: 0, Pkts Rvd: 0, Pkts Err: 0 Interface: Ethernet0/22 Status: Enabled, Pkts Snd: 0, Pkts Rvd: 0, Pkts Err: 0 Interface: Ethernet0/23 Status: Enabled, Pkts Snd: 11, Pkts Rvd: 12,
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Field Description Pkts Snd: 89 Number of NDP packets transmitted from a port Pkts Rvd: 262 Number of NDP packets received by a port Pkts Err: 0 Number of error NDP packets received by a port Neighbor 1: 170(s) Aging Time: The neighbor NDP information aging time connected by the port MAC Address MAC address of a neighbor device Port Name Port name of a neighbor device Sof
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands 2.1.3 ndp timer hello Syntax ndp timer hello seconds undo ndp timer hello View System view Parameter seconds: Specifies NDP packet interval and ranges from 5 to 254 in units of second. By default, NDP packets are transmitted every 60 seconds. Description Using ndp timer hello command, you can configure how often to transmit the NDP packets.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands will discard the received NDP neighbor node information. Using undo timer aging command, you can restore the default NDP information aging time. A user can specify how long an adjacent device will hold the information of the local device.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands 2.2 NTDP Configuration Commands 2.2.1 display ntdp Syntax display ntdp View Any view Parameter None Description Using display ntdp command, you can view the global NTDP information. The displayed information includes collected hops, ntdp timer, hop-delay, port-delay and time taken for last collection. This command is used for displaying the global NTDP information.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands 2.2.2 display ntdp device-list Syntax display ntdp device-list [ verbose ] View All view Parameter verbose: Display the detailed information about the device. Description Using display ntdp device-list command, you can view the device information collected through NTDP. Example # Display the device list collected through NTDP.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands VRP (tm) Software, Version 3.10 Quidway S3026 Software Version 3026-005, RELEASE SOFTWARE Copyright (c) 2000-2002 By HUAWEI TECH CO., LTD.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands undo ntdp enable View System view/Ethernet port view Parameter None Description Using ntdp enable command, you can enable NTDP on switch or a port. Using undo ntdp enable command, you can disable NTDP on switch or a port. By default, NTDP is enabled on switch and the ports supporting NDP. If NTDP is enabled on a port not supporting NDP, NTDP cannot run yet.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Description Using ntdp explore command, you can start topology information collection when you wants to collect network topology information. NTDP will collect the NDP information of every device and all of their neighboring connections in the specified network scope.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands 2.2.6 ntdp timer Syntax ntdp timer interval-in-mins undo ntdp timer View System view Parameter Interval-in-mins: The interval of collecting topology information periodically, ranging from 0 to 65535 in minutes. 0 indicates that no regular topology collection will be performed. Description Using ntdp timer command, you can configure the topology collection interval.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Description Using ntdp timer hop-delay command, you can configure delay for collected device to forward topology collection request. Using undo ntdp timer hop-delay command, you can restore the default delay value.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands This command is configured on the collecting device. The topology request contains the port-delay time, according to which the collected device decides how long it shall wait before the first port forwards the request. Example # Configure that the collected device shall delay for 40ms before the next port sends the request. [Quidway] ntdp timer port-delay 40 2.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Example # Add the candidate device, with MAC address 00E0-fc00-35e7 and super-password huawei, to the cluster, and its member number is 6. [Huawei_0.Quidway-cluster] add-member 6 mac-address 00E0-fc00-35e7 password huawei 2.3.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands View Cluster view Parameter recover: automatic get back the members of a cluster for the administrator device when it reboot. Description Using auto-build command, you can configure a cluster automatically. This command can be used on a candidate device or an administrator device.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Description Using build command, you can configure a cluster on a device. The name parameter specifies the name of the cluster. Using undo build command, you can cancel a cluster. By default, all the devices supporting cluster are candidate devices.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands View System view Parameter None Description Using cluster enable command, you can enable the cluster function on a switch. Using undo cluster enable command, you can disable the cluster function of a switch. By default, the cluster function is enabled on all the devices supporting cluster. Above commands can be used on any device supporting the cluster function.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands device for configuration management, or operate on a member device and switchover to an administrator device. Authentication is required when the user switch from the administrator device to a member device. Upon passing the member device authentication, the switchover is allowed.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Example # Delete the switch from cluster, its member number is 2. [Huawei_0.Quidway-cluster] delete-member 2 2.3.9 display cluster Syntax display cluster View Any view Parameter None Description Using display cluster command, you can view the state and basic configuration information of the cluster.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Table 2-5 Description of cluster status and statistics information Field Description Cluster name Name of the cluster Role Role of the cluster member Handshake timer Value of handshake timer Handshake hold-time Value of handshake hold-time IP-Pool IP pool of the cluster No logging host configured No SNMP host configured The corresponding configuration of the cluster No FT
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands 2.3.10 display cluster candidates Syntax display cluster candidates [ mac-address H-H-H | verbose ] View Any view Parameter mac-address H-H-H: MAC address of candidate device. verbose: Display the detailed information about the candidate device. Description Using display cluster candidates command, you can view candidate devices of the cluster.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches MAC : 00e0-fc00-a01f Hop : 2 Chapter 2 HGMP V2 Configuration Commands IP: Platform : Quidway S3026 Hostname : LSW1 MAC : 00e0-fc07-4de0 Hop : 1 IP: 1.5.6.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands display cluster members SN Device MAC Address Status Name 0 Quidway S3526 00e0-fc07-0bc0 Cmdr Huawei_0.Quidway 1 Quidway S3026 00e0-fc00.a01f Up Huawei_1.Quidway 2 Quidway S3526 00e0-fc07-4de0 Up Huawei_2.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Quidway S3026 Software Version 3026-005, RELEASE SOFTWARE Copyright (c) 2000-2002 By HUAWEI TECH CO., LTD. Member number: 2 Name:Huawei_2.LSW1 Device:Quidway S3526 MAC Address:00e0-fc07-4de0 Member status:Up Hops to administrator device:1 IP: 1.5.6.7/16 Version: Huawei Versatile Routing Platform Software VRP (tm) Software, Version 3.10 Copyright (c) 2000-2002 By HUAWEI TECH CO., LTD.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Description Using ftp-server command, you can configure the public FTP server for the cluster members on the administrator device. Using undo ftp-server command, you can configure administrator device as FTP server. By default, the administrator device acts as FTP Server. The member device within cluster will access FTP server via administrator device.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands 2.3.14 ip-pool Syntax ip-pool administrator-ip-address { ip-mask | ip-mask-length } undo ip-pool View Cluster view Parameter administrator-ip-address: IP address of the administrator device of the cluster. ip-mask: Mask of the cluster IP address pool. ip-mask-length: Mask length of the cluster IP address pool.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Parameter ip-address: IP address of logging host configured for the cluster. Description Using logging-host command, you can configure a public logging host for the member devices on the administrator device. Using undo logging-host command, you can cancel the logging host. By default, there is no public logging host configured.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands 2.3.17 reboot member Syntax reboot member { member-num | mac-address H-H-H } [ eraseflash ] View Cluster view Parameter member-num: Cluster member number. H-H-H: MAC address of the member device to be reset. eraseflash: Delete the configuration file when resetting the member device.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands Description Using snmp-host command, you can configure the public SNMP host for the members inside a cluster on the administrator device. Using undo snmp-host command, you can cancel the public SNMP host. By default, there is no public SNMP host.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 2 HGMP V2 Configuration Commands 2.3.20 timer Syntax timer interval-in-secs undo timer View Cluster view Parameter Interval-in-secs: This parameter is to set sending time interval of the handshake packet, ranging of 1 ~ 255 seconds. By default ,the value is 10 seconds. Description Using timer command, you can configure the interval of handshake packets.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 3 Multicast MAC Address for Cluster Management Commands Chapter 3 Multicast MAC Address for Cluster Management Commands 3.1 Multicast MAC Address for Cluster Management Commands 3.1.1 cluster-mac Syntax cluster-mac H-H-H View Cluster view Parameter H-H-H: MAC address of the client host, in hexadecimal notation. It is in the range of 0180-C200-0000 or 0180-C200-000A and 0180-C200-0020 to 0180-C200-002F.
Command Manual - Integrated Management Quidway S3000-EI Series Ethernet Switches Chapter 3 Multicast MAC Address for Cluster Management Commands Parameter time-interval: Time interval for sending multicast messages, in minutes. Description Use the cluster-mac syn-interval command to set the time interval for sending multicast messages on the management device. You can only use this command on the management device.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual STP Huawei Technologies Proprietary
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 MSTP Configuration Commands ............................................................................... 1-1 1.1.1 active region-configuration ...................................................................................... 1-1 1.1.2 check region-configuration ...................................................................................... 1-1 1.1.3 display stp ......................
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Table of Contents 1.1.38 stp transit-limit ..................................................................................................... 1-35 1.1.39 vlan-mapping modulo..........................................................................................
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Chapter 1 MSTP Configuration Commands 1.1.1 active region-configuration Syntax active region-configuration View MST region view Parameter None Description Using active region-configuration command, you can activate the configurations of MST region. This command is used for manually activate the configurations of MST region.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Parameter None Description Using check region-configuration command, you can view the configuration information (including switch region name, revision level, and VLAN mapping table) to be activated. MSTP defines that the user must ensure the correct region configurations, especially the VLAN mapping table configuration.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 1.1.3 display stp Syntax display stp [ instance instance-id ] [ interface interface-list | slot slot-num ] [ brief ] View Any view Parameter instance-id: Specifies the spanning tree instance ID, ranging from 0 to 16, instance 0 is CIST.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 2) CIST port parameter: Port state, role, priority, path cost, designated bridge, designated port, edge port/non-edge port, whether connected to the point-to-point link, port transit limit, whether to enable Root protection, whether being a region edge port, Hello Time, Max Age, Forward Delay, Message-age time, and Remaining-hops; 3) Global MSTIs parameter: MSTI instance ID, bridge priority of the instance
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 1.1.4 display stp region-configuration Syntax display stp region-configuration View Any view Parameter None Description Using display stp region-configuration command, you can view the effective MST region configurations . MST region configuration information includes: region name, region revision level, and associations between VLANs and STIs.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 1.1.5 instance Syntax instance instance-id vlan vlan-list undo instance instance-id [ vlan vlan-list ] View MST region view Parameter instance-id: Specifies the spanning tree instance ID, ranging from 0 to 16, instance 0 is CIST. vlan-list: Specifies the VLAN list and expressed as vlan-list = { vlan-id [ to vlan-id ] }&<1-10>. VLAN ID ranges from 1 to 4094.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands undo region-name View MST region view Parameter name: Specifies the MST region name of the switch with a character string not exceeding 32 bytes. Description Using region-name command, you can configure the MST region name of a switch. Using undo region-name command, you can restore the default MST region name.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands The spanning tree statistics information includes TCN, Config BPDU, RST, and MST BPDU, received and transmitted on the port. Among them, STP BPDU and TCN BPDU are counted on CIST. When the spanning tree ID and port list are specified, the command clears the statistics information of the specified spanning tree on the specified port.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 1.1.9 stp Syntax stp { enable | disable } undo stp View System view, Ethernet port view Parameter enable: Enables global or port MSTP. disable: Disables global or port MSTP. Description Using stp command, you can enable or disable MSTP on a device or a port. Using undo stp command, you can restore the default MSTP state on a device or a port. By default, MSTP is disabled on the switch.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Parameter None Description Using stp bpdu-protection command, you can enable the BPDU protection on the switch. Using undo stp bpdu-protection command, you can restore the default state of BPDU protection. By default, BPDU protection is disabled. Generally, the access ports of the access layer devices are directly connected to user terminals (such as PC) or file servers.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands The network diameter refers to the maximum count of switches on the path between any two terminal devices. The definition of network diameter: Maximum count of switches between the farthest communication ends. stp bridge-diameter command configures the switching network diameter and determines the three time parameters of MSTP accordingly.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands The switch priority takes part in the spanning tree calculation. It is configured separately for every STI. Different STIs can be configured with different priorities. If specifying the instance ID as 0, the command can configure the CIST priority. If user doesn’t input parameter “instance instance-id“ when configuring switch, the configuration will only be effective on CIST.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Because the edge port is not connected to any other switches, it will not receive the configuration BPDUs from them. Before BPDU PROTECTION is enabled on the switch, the port received a BPDU runs as a non-edge port, even if it is configured as edge port. For the related command, see stp interface edged-port. Example # Configure ethernet0/1 as an edge port. [Quidway-Ethernet0/1] stp edged-port disable 1.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Table 1-4 Cost corresponding to the port speed Link speed Recommended value Recommended value range Value range 10Mbps 2,000 200- 20000 1-200000 100Mbps 200 20-2000 1-200000 1Gbps 20 2-200 1-200000 10G/s 2 2-20 1-200000 Above 10G/s 1 1-2 1-200000 For the related command, see stp interface cost . Example # Set the path cost of ethernet0/3 on STI 2 to 200.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands If user doesn’t input parameter “instance instance-id“ when configuring switch, the configuration will only be effective on CIST. For the related command, see stp interface port priority. Example # Set the priority of ethernet0/3 on STI 2 to 16. [Quidway-Ethernet0/3] stp instance 2 port priority 16 1.1.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands parameter to overwrite it. Normally, you are recommended to set the network diameter to get the other two time parameter of the switch accordingly. Caution: z In a switching network, you can configure only one root bridge for each STI and one or more secondary switches. Do not configure more than one root bridge for an STI at the same time, otherwise, the calculation result will be unpredictable.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Description Using stp root secondary command, you can configure the current switch as the secondary root bridge of a specified STI. Using undo stp root command, you can cancel the current switch for the secondary root bridge of a specified STI. If user doesn’t input parameter “instance instance-id“ when configuring switch, the configuration will only be effective on CIST.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands enable: Enables MSTP on the port. disable: Disables MSTP on the port. Description Using stp interface command, you can enable/disable MSTP on a switch port in system view. By default, if MSTP is enabled globally, it is enabled on every port; if MSTP is disabled globally, it is also disabled on every port.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands disable: Configure the current port as a non-edge port. Description Using stp interface edged-port enable command, you can configure a port as an edge port in system view. Using stp interface edged-port disable command, you can configure a port as a non-edge port in system view. Using undo stp interface edged-port command, you can restore the non-edge port, as defaulted.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands in Port Command Manual. &<1-10> means that the preceding parameters can be entered up to 10 times. instance-id: Specifies the spanning tree instance ID, ranging from 0 to 16, instance 0 is CIST. cost cost: Specifies the path cost of the port, ranging from 1 to 200000. Description Using stp interface cost command, you can configure the path cost of the specified port on the specified STI in system view.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 1.1.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 1.1.22 stp interface loop-protection Syntax stp interface interface-list loop-protection undo stp interface interface-list loop-protection View System view Parameter interface-list: Ethernet port list, containing multiple Ethernet ports and expressed as interface _list = { { interface_type interface_num | interface_name } [ to { interface_type interface_num | interface_name } ] }&<1-10>.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands in Port Command Manual. &<1-10> means that the preceding parameters can be entered up to 10 times. Description Using stp interface mcheck command, you can perform mcheck operation on the port in system view. If a port of an MSTP switch on a switching network has ever been connected to an STP switch, the port will automatically transit to operate in STP-compatible mode.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Description Using stp interface point-to-point command, you can configure a port (not) to be connected to a point-to-point link in system view. Using undo stp interface point-to-point command, you can restore the default state of the link to the Ethernet port. By default, the parameter defaults to auto, that is, MSTP checks if the link to the Ethernet port is a point-to-point link.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Description Using stp interface root-protection command, you can enable Root protection on the switch in system view. Using undo stp interface root-protection command, you can restore the default Root protection state. By default, Root protection is disabled.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands packetnum: Specifies the amount limit to the transmitted packets, ranging from 1 to 255 (expressed as a counter value without any units). By default, the transmission limit on every port is 3. Description Using stp interface transit-limit command, you can configure an amount limit to the configuration BPDU transmitted via a port during the Hello Time in system view.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 1.1.28 stp max-hops Syntax stp max-hops hop undo stp max-hops View System view Parameter hop: Specifies the max hops, ranging from 1 to 40. By default, MST region Max Hops is 20. Description Using stp max-hops command, you can configure the Max Hops of an MST region. Using undo stp max-hops command, you can restore the default Max Hops.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Description Using stp mcheck command, you can perform mcheck on the current port. If a port of an MSTP switch on a switching network has ever been connected to an STP switch, the port will automatically transit to operate in STP-compatible mode. However, when the STP switch is removed, the port stays in STP-compatible mode and cannot automatically transit back to MSTP mode.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands [Quidway] stp mode stp 1.1.31 stp point-to-point Syntax stp point-to-point { force-true | force-false | auto } undo stp point-to-point View Ethernet port view Parameter force-true: Indicates the Ethernet port connected to a point-to-point link. force-false: Indicates the Ethernet port not connected to a point-to-point link.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 1.1.32 stp region-configuration Syntax stp region-configuration undo stp region-configuration View System view Parameter None Description Using stp region-configuration command, you can enter MST region view. Using undo stp region-configuration command, you can restore the default MSTP region configurations. By default, the three MST region parameters take the default values.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Description Using the stp tc-protection enable command, you can enable the protection function from being attacked by TC-BPDU packets on the switch. Using the stp tc-protection disable command, you can disable the protection function. By default, the protection from TC-BPDU packet attack is enabled.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands change errors. Due to the illegal change, the traffic supposed to travel over the high-speed link may be pulled to the low-speed link and congestion will occur on the network. MSTP provides Root protection function to protect the root bridge: The port configured with Root protection only plays a role of designated port on every instance.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 2 * (Forward Delay - 1.0 seconds) >= Max Age Max Age >= 2 * (Hello Time + 1.0 seconds) Only if the above-mentioned formulas are equal can the MSTP normally operate on the entire network, otherwise, the network may flap frequently.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Only if the above-mentioned formulas are equal can the MSTP normally operate on the entire network, otherwise, the network may flap frequently. You are recommended to use the stp root primary command to specify the diameter of the switching network, so that MSTP can automatically calculate and give the moderate values for the time parameters.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands Only if the above-mentioned formulas are equal can the MSTP normally operate on the entire network, otherwise, the network may flap frequently. You are recommended to use the stp root primary command to specify the diameter of the switching network, so that MSTP can automatically calculate and give the moderate values for the time parameters.
Command Manual - STP Quidway S3000-EI Series Ethernet Switches Chapter 1 MSTP Configuration Commands 1.1.39 vlan-mapping modulo Syntax vlan-mapping modulo modulo View MST region view Parameter modulo: Specifies the modulus, ranging from 1 to 16. Description Using vlan-mapping modulo command, you can map a VLAN list to an STI. By default, all the VLANs are mapped to CIST, namely Instance 0. MSTP describes the association between VLANs and STIs with the VLAN mapping table.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual Security Huawei Technologies Proprietary
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 802.1x Configuration Commands .............................................................................. 1-1 1.1 802.1x Configuration Commands ...................................................................................... 1-1 1.1.1 display dot1x ........................................................................................................... 1-1 1.1.2 dot1x...............
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Table of Contents 2.1.17 state..................................................................................................................... 2-16 2.1.18 vlan-assignment-mode........................................................................................ 2-17 2.2 RADIUS Protocol Configuration Commands ................................................................... 2-18 2.2.1 accounting-on enable..........................
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands Chapter 1 802.1x Configuration Commands 1.1 802.1x Configuration Commands 1.1.1 display dot1x Syntax display dot1x [ sessions | statistics ] [ interface interface-list ] View Any view Parameter sessions: Configures to display the session connection information of 802.1x. statistics: Configures to display the relevant statistics information of 802.1x. interface: Configures to display the 802.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands the port number and interface-name specifies the port name. For the respective meanings and value ranges, read the Parameter of the Port Configuration section. Description Using dot1x command, you can enable 802.1x on the specified port or globally (i.e., on the current device). Using undo dot1x command, you can disable the 802.1x on the specified port or globally. By default, 802.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands eap: Use EAP authentication method. Description Using dot1x authentication-method command, you can configure the authentication method for 802.1x user. Using undo dot1x authentication-method command, you can restore the default authentication method of 802.1x user. By default, CHAP authentication is used for 802.1x user authentication.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands Description Using dot1x dhcp-launch command, you can set 802.1x to disable the switch to trigger the user ID authentication over the users who configure static IP addresses in DHCP environment. Using undo dot1x dhcp-launch command, you can set 802.1x to enable the switch to trigger the authentication over them.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches 1) Chapter 1 802.1x Configuration Commands If the users obtain their IP addresses dynamically, you must couple dynamic user binding with DHCP Snooping in the following way: z Enable DHCP Snooping globally on the switch. z Configure the switch port connecting to the DHCP server to be a DHCP Snooping trusted port. 2) If the users use static IP addresses, they must use 802.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands When you execute this command in Ethernet port view, you can only enable Guest VLAN on the current port, and the interface-list parameter cannot be input. Note the following: z Guest VLAN is only supported in the port-based authentication mode. z A switch only can be configured with one Guest VLAN.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands Description Using dot1x max-user command, you can configure a limit to the amount of supplicants on the specified interface of 802.1x. Using undo dot1x max-user command, you can restore the default value. This command is used for setting a limit to the amount of supplicants that 802.1x can hold on the specified interface.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands interface-num specifies a single Ethernet interface in the format interface-num = { interface-type interface-num | interface-name }, where interface-type specifies the interface type, interface-num specifies the interface number and interface-name specifies the interface name. For the respective meanings and value ranges, read the Parameter of the Port Command Manual section.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands interface type, interface-num specifies the interface number and interface-name specifies the interface name. For the respective meanings and value ranges, read the Parameter of the Port Command Manual section. Description Using dot1x port-method command, you can configure the base for 802.1x to perform access control on the specified interface.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands Description Using dot1x quiet-period command, you can enable the quiet-period timer. Using undo dot1x quiet-period command, you can disable this timer. If an 802.1x user has not passed the authentication, the Authenticator will keep quiet for a while (which is specified by quiet-period timer) before launching the authentication again.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands Before configuring 802.1x re-authentication feature on a port, you must enable the feature both globally and on this port. Example # Enable 802.1x reauthentication on port Ethernet 0/1. [Quidway-Ethernet0/1] dot1x re-authenticate Re-authentication is enabled on port Ethernet 0/1 1.1.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands 1.1.13 dot1x retry-version-max Syntax dot1x retry-version-max max-retry-version-value undo dot1x retry-version-max View System view Parameter max-retry-version-value: The maximum retry times for a device to send the version request frame to an access user. The value ranges form 1 to 10, and defaults to 3.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands trap: Sends trap message upon detecting a user using proxy to access the switch. interface interface-list: Ethernet interface list including several Ethernet interfaces, expressed in the format interface-list = { interface-num [ to interface-num ] } & < 1-10 >.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands 1.1.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands tx-period: Specify the transmission timeout timer. After the Authenticator sends the Request/Identity request packet which requests the user name or user name and password together, the tx-period timer of the Authenticator begins to run. If the Supplicant does not respond back with authentication reply packet successfully, then the Authenticator will resend the authentication request packet.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands Parameter interface interface-list: Ethernet interface list, represents multiple Ethernet interfaces, in the format of interface-list = { interface-num [ to interface-num ] } & < 1-10 >. interface-num is a single Ethernet port, in the format of interface-num = { interface-type interface-num | interface-name }. Description Using the dot1x version-check command, you can enable the 802.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 1 802.1x Configuration Commands This command can be used to re-perform statistics if the user wants to delete the former statistics of 802.1x. When the original statistics is cleared, if no port type or port number is specified, the global 802.1x statistics of the switch and 802.1x statistics on all the ports will be cleared. If the port type and port number are specified, the 802.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Chapter 2 AAA & RADIUS Protocol Configuration Commands 2.1 AAA Configuration Commands 2.1.1 access-limit Syntax access-limit { disable | enable max-user-number } undo access-limit View ISP domain view Parameter disable: No limit to the supplicant number in the current ISP domain.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands 2.1.2 attribute Syntax attribute { ip ip-address | mac mac-address | idle-cut second | access-limit max-user-number | vlan vlanid | location { nas-ip ip-address port portnum | port portnum } undo attribute { ip | mac | idle-cut | access-limit | vlan | location }* View Local user view Parameter ip: Specifies the IP address of a user.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Example # Configure the IP address 10.110.50.1 to the user huawei1. [Quidway-luser-huawei1] attribute ip 10.110.50.1 2.1.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Description Using cut connection command, you can disconnect a user or a category of users by force. For the related command, see display connection. Example # Cut all the connections in the ISP domain, huawei163.net. [Quidway] cut connection domain huawei163.net 2.1.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands exceeding 80 characters, excluding “/”, “:”, “*”, “?”, “<”, “>”, and so on. The @ character can only be used once in one username. The pure username (the part before @, namely the user ID) cannot exceed 55 characters. Description Using display connection command, you can view the relevant information of all the supplicants or the specified one(s).
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Example # Display the summary information of all ISP domains of the system. display domain 0 Domain = system State = Active Access-limit = Disable Vlan-assignment-mode = Integer Domain User Template: Idle-cut = Disable Self-service = Disable Messenger Time = Disable Default Domain Name: system Total 1 domain(s).1 listed. 2.1.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands user-name user-name : Configures to display a user specified with user-name . user-name is the argument specifying the username. It is a character string not exceeding 80 characters, excluding “/”, “:”, “*”, “?”, “<”, “>”, and so on. The @ character can only be used once in one username. The pure username (the part before @, namely the user ID) cannot exceed 55 characters.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Field Description MAC address The MAC address of the user FTP Directory The directory authorized to FTP users 2.1.7 domain Syntax domain { isp-name | default { disable | enable isp-name } } undo domain isp-name View System view Parameter isp-name: Specifies an ISP domain name.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands For a switch, each supplicant belongs to an ISP domain. The system supports to configure up to 16 ISP domains. If a user has not reported its ISP domain name, the system will put it into the default domain. When this command is used, if the specified ISP domain does not exist, the system will create a new ISP domain. All the ISP domains are in the active state when they are created.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Because a user template only works in one ISP domain, it is necessary to configure user template attributes for users from different ISP domain respectively. For the related command, see domain Example # Enable the user in the current ISP domain, huawei163.net, to use the idle-cut attribute specified in the user template (that is, enabling the user to use the idle-cut function).
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands [Quidway-luser-huawei1] 2.1.10 local-user password-display-mode Syntax local-user password-display-mode { cipher-force | auto } undo local-user password-display-mode View System view Parameter cipher-force: Forced cipher mode specifies that the passwords of all the accessed users must be displayed in cipher text.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Parameter limit: Remaining-online-time threshold in minutes, in the range of 1 to 60. When the remaining online time of a user is equal to this threshold, the switch begins to send alert messages to the client. interval: Sending interval of alert messages in minutes, in the range of 5 to 60. It must be a multiple of 5.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Parameter string: Name of the delivered VLAN. Description Using name command, you can configure name of the delivered VLAN. For the related commands, see vlan-assignment-mode. Example # Configure name of the delivered VLAN [Quidway-vlan100] name test 2.1.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Example # Set the user huawei1 to display the password in simple text, given the password is 20030422. [Quidway-luser-huawei1] password simple 20030422 2.1.14 radius-scheme Syntax radius-scheme radius-scheme-name undo radius-scheme View ISP domain view Parameter radius-scheme-name: Specifies a RADIUS server group, with a character string not exceeding 32 characters.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands View ISP domain view Parameter url-string: The URL address of the page used to change the user password on the self-service server, a string with 1 to 64 characters. This string cannot contain "?" character. If "?" is contained in the URL address, you must replace it with "|" when inputting the URL address in the command line.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands View Local user view Parameter telnet: Specifies user type as Telnet. ssh: Specifies user type as SSH. level level: Specifies the level of Telnet or SSH users. The argument level is an integer in the range of 0 to 3 and defaults to 1. ftp: Specifies user type as ftp. ftp-directory directory: Specifies the directory of ftp users, directory is a character string of up to 64 characters.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Description Using state command, you can configure the state of the current ISP domain/ current user. By default, after an ISP domain is created, it is in the active state (in ISP domain view). A local user will be active (in local user view) upon its creation. In ISP domain view, every ISP can either be in active or block state.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches z Chapter 2 AAA & RADIUS Protocol Configuration Commands String ID: The switch compares the string ID delivered from the server with the VLAN names existing on the switch. If a matching entry is found, the switch adds the port into the corresponding VLAN. Otherwise, the delivery fails and the user cannot pass the authentication.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Description Using the accounting-on enable command, you can enable user re-authentication at reboot. Using the undo accounting-on enable command, you can disable this function. Using the undo accounting-on send command, you can restore the default number for sending Accounting-On packets.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands [Quidway-radius-CAMS] accounting-on enable 2.2.2 accounting optional Syntax accounting optional undo accounting optional View RADIUS scheme view Parameter None Description Using the accounting optional command, you can enable the selection of RADIUS accounting option. Using the undo accounting optional command, you can disable the selection of RADIUS accounting option.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Parameter data: Set data unit. byte: Set 'byte' as the unit of data flow. giga-byte: Set 'giga-byte' as the unit of data flow. kilo-byte: Set 'kilo-byte' as the unit of data flow. mega-byte: Set 'mega-byte' as the unit of data flow. packet: Set data packet unit. giga-packet: Set 'giga-packet' as the unit of packet flow. kilo-packet: Set 'kilo-packet' as the unit of packet flow.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands For the related command, see local-server. Example # Display the statistics of local RADIUS authentication server. display local-server statistics The localserver packet statistics: Receive: 0 Send: 0 Discard: 0 Receive Packet Error: 0 Auth Reveive: 0 Auth Send: 0 Acct Receive: 0 Acct Send: 0 2.2.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Acct Server Encryption Key= huawei Accounting method = required TimeOutValue(in second)=3 RetryTimes=3 RealtimeACCT(in minute)=12 Permitted send realtime PKT failed counts =5 Retry sending times of noresponse acct-stop-PKT =500 Username format =without-domain Data flow unit =Byte Packet unit =1 -----------------------------------------------------------------Total 1 RADIUS sch
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Code= 3,Num=0 ,Err=0 Code= 5,Num=0 ,Err=0 Code=11,Num=0 ,Err=0 Code=22,Num=0 ,Err=0 Chapter 2 AAA & RADIUS Protocol Configuration Commands Running statistic: RADIUS received messages statistic: Normal auth request ,Num=0 ,Err=0 ,Succ=0 EAP auth request ,Num=0 ,Err=0 ,Succ=0 Account request ,Num=0 ,Err=0 ,Succ=0 Account off request ,Num=0 ,Err=0 ,Succ=0 Leaving request ,Num=0 ,Err=0 ,Succ=0 … (Omitted) 2.2.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Description Using display stop-accounting-buffer command, you can view the stopping accounting requests, which have not been responded and saved in the buffer.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Description Using key command, you can configure encryption key for RADIUS authentication/authorization or accounting packet. Using undo key command, you can restore the default key. RADIUS client (switch system) and RADIUS server use MD5 algorithm to encrypt the exchanged packets. The two ends verify the packet through setting the encryption key.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Description Using local-server command, you can configure the parameters of local RADIUS server. Using undo local-server command, you can cancel a local RADIUS server. RADIUS service, which adopts authentication/authorization/accounting servers to manage users, is widely used in Quidway series switches.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Description Using the nas-ip command, you can set the source IP address of the network access server (NAS, the switch in this manual), so that all packets destined for the RADIUS server carry the same source IP address. Using the undo nas-ip command, you can cancel the configuration.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands After creating a RADIUS scheme, you are supposed to set IP addresses and UDP port numbers for the RADIUS servers, including primary/second authentication/authorization servers and accounting servers. In real networking environments, the above parameters shall be set according to the specific requirements.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands requirements. However, at least you have to set one authentication/authorization server and an accounting server. Besides, ensure that the RADIUS service port settings on the Ethernet switch is consistent with the port settings on the RADIUS server. For the related commands, see key, radius scheme , state.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands 2.2.14 radius scheme Syntax radius scheme radius-scheme-name undo radius scheme radius-scheme-name View System view Parameter radius-scheme-name: Specifies the Radius server name with a character string not exceeding 32 characters. Description Using radius scheme command, you can configure a RADIUS scheme and enter its view.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands 2.2.15 reset radius statistics Syntax reset radius statistics View User view Parameter None Description Using the reset radius statistics command, you can clear the statistic information related to the RADIUS protocol. For the related command, see display radius. Example # Clear the RADIUS protocol statistics. reset radius statistics 2.2.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands time is expressed in the format hh:mm:ss-yyyy/mm/dd. When this parameter is set, all the stopping accounting requests saved since start-time to stop-time will be deleted. user-name user-name : Configures to delete the stopping accounting requests from the buffer according to the username. User-name specifies the username, a character string not exceeding 80 characters.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Description Using retry command, you can configure retransmission times of RADIUS request packet. Using undo retry command, you can restore the retransmission times to default value. Because RADIUS protocol uses UDP packets to carry the data, its communication process is not reliable.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands disconnect the user at NAS end and on RADIUS server synchronously when some unexpected failure occurs. Quidway Series Ethernet Switches support to set maximum times of real-time accounting request failing to be responded. NAS will disconnect the user if it has not received real-time accounting response from RADIUS server for some specified times.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Example # Indicate that, when stopping accounting request for the RADIUS scheme “Huawei”, the switch will retransmit the packets for up to 1000 times. [Quidway-radius-huawei] retry stop-accounting 1000 2.2.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands View RADIUS scheme view Parameter ip-address: IP address, in dotted decimal format. By default, the IP addresses of second authentication/authorization is at 0.0.0.0. port-number: Specifies the UDP port number, ranging from 1 to 65535.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands according to the regulation and packet format of IP Hotel (an extension of RADIUS protocol). portal: Configures the switch system to support the RADIUS server of portal type, which requires the RADIUS client end (switch system) and RADIUS server to interact according to the regulation and packet format of Portal (an extension of RADIUS protocol).
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands active: Configures the RADIUS server to be active, namely the normal operation state. Description Using state command, you can configure the state of RADIUS server. By default, all the RADIUS servers in every RADIUS scheme are in the state of block.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Because the stopping accounting request concerns account balance and will affect the amount of charge, which is very important for both the user and ISP, NAS shall make its best effort to send the message to RADIUS accounting server.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Example # Set the response timeout timer of RADIUS scheme, huawei, to 5 seconds. [Quidway-radius-huawei] timer 5 2.2.26 timer quiet Syntax timer quiet minutes undo timer quiet View RADIUS scheme view Parameter minutes: Quiet time interval, ranging from 1 to 255, in minutes. The default value is 5.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands Parameter minutes: Real-time accounting interval, ranging from 3 to 60 and measured in minutes. By default, the value is 12. It must be a multiple of 3. Description Using timer realtime-accounting command, you can configure the real-time accounting interval. Using undo timer realtime-accounting command, you can restore the default interval.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 2 AAA & RADIUS Protocol Configuration Commands without-domain: Specifies to send the username without domain name to RADIUS server. Description Using user-name-format command, you can configure the username format sent to RADIUS server.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 3 HABP Configuration Commands Chapter 3 HABP Configuration Commands 3.1 HABP Commands 3.1.1 display debugging habp Syntax display debugging habp View Any view Parameter None Description Using the display debugging habp command, you can view HAMP debugging state. Example # Display HABP debugging state. [Quidway] display debugging habp HABP Debugging switch is on 3.1.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 3 HABP Configuration Commands Example # Display configuration information and state of HABP attribute.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 3 HABP Configuration Commands View Any view Parameter None Description Using the display habp traffic command, you can view HABP packet statistics. Example # Display HABP packet statistics. [Quidway] display habp traffic HABP counters : Packets output: 0, Input: 0 ID error: 0, Type error: 0, Version error: 0 Sent failed: 0 3.1.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 3 HABP Configuration Commands [Quidway] habp enable 3.1.6 habp server vlan Syntax habp server vlan vlan-id undo habp server View System view Parameter vlan-id: VLAN ID, in range of 1~4094 Description Using the habp server vlan command, you can set HABP mode as server and specify transmitting HABP packets in a specific VLAN. Using the undo hapb server vlan command, you can restore the HABP mode to the default value.
Command Manual - Security Quidway S3000-EI Series Ethernet Switches Chapter 3 HABP Configuration Commands Description Using the habp timer command, you can define time interval for a switch to send HABP request packet. Using the undo habp timer command, you can restore the time interval to the default value. The command is only available on the switch whose HABP mode is set as server. Example # Define the time interval to send HABP request packets as 50 seconds.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual Network Protocol Huawei Technologies Proprietary
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 ARP Configuration Commands .................................................................................. 1-1 1.1 ARP Configuration Commands.......................................................................................... 1-1 1.1.1 arp check enable ..................................................................................................... 1-1 1.1.2 arp static....
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Table of Contents 6.1.1 display fib ................................................................................................................ 6-1 6.1.2 display icmp statistics.............................................................................................. 6-2 6.1.3 display ip socket ...................................................................................................... 6-3 6.1.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 1 ARP Configuration Commands Chapter 1 ARP Configuration Commands 1.1 ARP Configuration Commands 1.1.1 arp check enable Syntax arp check enable undo arp check enable View System view Parameter None Description Using arp check enable command, you can enable the checking of ARP entry, that is, the device does not learn the ARP entry where the MAC address is multicast MAC address.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 1 ARP Configuration Commands Parameter ip-address: IP address of the ARP mapping entry. mac-address: MAC address of ARP mapping entry, whose format is H-H-H ( H indicates a hexadecimal number). vlan-id: VLAN to which the static ARP entry belongs, which is in the range of 1 to 4094. interface-name: Port to which the static ARP entry belong, represented with interface-name= interface-type interface-number.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 1 ARP Configuration Commands aging-time: Aging time of dynamic ARP aging timer, which is in the range of 1 to 1440 minutes. By default, the aging time is 20 minutes. Description Using arp timer aging command, you can configure the dynamic ARP aging timer. Using undo arp timer aging command, you can restore the default dynamic ARP aging time. For the related command, see display arp timer aging.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches : 0050-ba22-6fd7, Chapter 1 ARP Configuration Commands sender_ip_addr : 10.110.91.193, target_eth_addr 00e0-fc00-3 500, target_ip_addr : 10.110.91.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 1 ARP Configuration Commands Table 1-2 Output description of the display arp display Field Description IP Address IP address of the ARP mapping entry MAC Address MAC address of the ARP mapping entry VLAN ID VLAN to which the static ARP entry belongs Port Name Port to which the static ARP entry belongs Aging Aging time of dynamic ARP entry in minutes Type Type of ARP entry 1.1.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 1 ARP Configuration Commands Parameter dynamic: Clear the dynamic ARP mapping entries. static: Clear the static ARP mapping entries interface interface-name: Clear the ARP mapping entries that are related to the specified. port, represented with interface-name= interface-type interface-number. interface-type is port type and interface-number is port number.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches z Chapter 1 ARP Configuration Commands By sending gratuitous ARP packets, network devices can figure out whether the IP addresses of other devices conflict with its own. z If the device which sends the gratuitous ARP packet changed its hardware address (probably, it turns off, has its interface card changed, and then reboots), this packet can make old hardware address in the cache of other devices update accordingly.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 2 DHCP-Snooping Configuration Commands Chapter 2 DHCP-Snooping Configuration Commands 2.1 DHCP-Snooping Configuration Commands 2.1.1 dhcp-snooping Syntax dhcp-snooping undo dhcp-snooping View System view Parameter None Description Using dhcp-snooping command, you can enable DHCP-Snooping function on the switch to record users’ IP addresses. Using undo dhcp-snooping command, you can disable this function.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 2 DHCP-Snooping Configuration Commands Parameter None Description Using dhcp-snooping trust command, you can configure a trusted port. Using undo dhcp-snooping trust command, you can restore the trusted port as distrusted. By default, the switch ports are set as distrusted. For the related command, see display dhcp-snooping trust. Example # Configure Ethernet0/1 as a trusted port.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches dynamic Chapter 2 DHCP-Snooping Configuration Commands 202.38.12.45 00e0-fc00-0006 286 1 Ethernet0/1 2.1.4 display dhcp-snooping count Syntax display dhcp-snooping count View Any view Parameter None Description Use the display dhcp-snooping count command to display the number of the DHCP-Snooping entries in the binding table. Example # Display the number of the DHCP-Snooping entries in the binding table.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 2 DHCP-Snooping Configuration Commands display dhcp-snooping trust dhcp-snooping is enabled dhcp-snooping trust become effective Interface Trusted ================================= Ethernet0/1 Trusted Huawei Technologies Proprietary 2-4
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 3 DHCP Client Configuration Commands Chapter 3 DHCP Client Configuration Commands 3.1 DHCP Client Configuration Commands 3.1.1 debugging dhcp client Syntax debugging dhcp client { all | error | event | packet } undo debugging dhcp client { all | error | event | packet } View User view Parameter all: All DHCP client debugging. error: DHCP client error (including packet unrecognizable ) debugging.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 3 DHCP Client Configuration Commands Parameter verbose: Displays detailed information about address allocation at DHCP client. Description Using the display dhcp client command, you can view detailed information about address allocation at DHCP client. Example # Display detailed information about address allocation at DHCP client.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 3 DHCP Client Configuration Commands Example # Configure VLAN interface to obtain IP address using DHCP.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 4 BOOTP Client Configuration Commands Chapter 4 BOOTP Client Configuration Commands 4.1.1 debugging bootp client Syntax debugging bootp client undo debugging bootp client View User view Parameter None Description Using the debugging bootp client command, you can enable BOOTP client debugging. Using the undo debugging bootp client command, you can disable BOOTP client debugging.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 4 BOOTP Client Configuration Commands Using the display bootp client command, you can view the information about BOOTP client, including its MAC address and the applied IP address etc. Example # Display the information about BOOTP client. [Quidway] display bootp client interface vlan-interface 1 Vlan-interface1: Allocated IP: 169.254.0.2 255.255.0.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 5 Access Management Configuration Commands Chapter 5 Access Management Configuration Commands 5.1 Access Management Configuration Commands 5.1.1 am enable Syntax am enable undo am enable View System view Parameter None Description Using am enable command, you can enable the access management function. Using undo am enable command, you can disable the function. By default, Access management function disabled.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 5 Access Management Configuration Commands View Ethernet port view Parameter interface-list: Specifies a list of ports isolated from the specified port in the { { interface-type interface-number | interface-name } [ to { interface-type interface-number | interface-name } ] } &<1-10> format. interface-name: Specified the port name, represented with interface-name= interface-type interface-number.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 5 Access Management Configuration Commands Parameter interface-name: Specifies the port name in the interface-name= interface-type interface-number format. interface-type: Specifies the port type. interface-number: Specifies the port number. For parameter description, refer to the interface command. mac: MAC address. ip: IP address. Description Using am user-bind command, you can bind port, IP address and MAC address.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 5 Access Management Configuration Commands Example # Display the access management configurations on Ethernet0/1 and Ethernet0/2.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 5 Access Management Configuration Commands Description Using display am user-bind command, you can view Port, IP address and MAC address binding information. Example # Display binding information of Ethernet0/1 port. display am user-bind interface ethernet0/1 Mac IP Port NULL 129.10.1.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands Chapter 6 IP Performance Configuration Commands 6.1 IP Performance Configuration Commands 6.1.1 display fib Syntax display fib View Any view Parameter None Description Using display fib command, you can view the summary of the Forwarding Information Base. The information includes: destination address/mask length, next hop, current flag and outbound interface.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands Table 6-1 Description of the output information of the display fib command Field Description The flag options include: B – Blackhole route D – Dynamic route G – Gateway route Flag H – Local host route S – Static route U – Route in UP status R – Unreachable route L – Route generated by ARP or ESIS 6.1.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches echo reply 5 timestamp 0 Chapter 6 IP Performance Configuration Commands parameter problem information reply mask requests 0 mask replies 0 0 0 time exceeded 0 Table 6-2 Description of the output information of the display icmp statistics command Field Description bad formats Number of input packets in bad format bad checksum Number of input packets with wrong checksum echo Number of input/output echo request packets
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands Description Using the display ip socket command, you can display the information about the sockets in the current system. Example # Display the information about the socket of TCP type. display ip socket socktype 1 SOCK_STREAM: Task = VTYD(18), socketid = 1, Proto = 6, LA = 0.0.0.0:23, FA = 0.0.0.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands Field Description socket state The state of the socket 6.1.4 display ip statistics Syntax display ip statistics View Any view Parameter None Description Using display ip statistics command, you can view the statistics information about IP packets. For the related command, see display ip interface vlan-interface, reset ip statistics. Example # View statistics about IP packets.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands Table 6-4 Description of the output information of the display ip statistics command Field Input: Output: Fragment: Reassembl ing: Description sum Sum of input packets local Number of received packets whose destination is the local device bad protocol Number of packets with wrong protocol number bad format Number of packets in bad format bad checksum Number of packets
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands Description Using display tcp statistics command, you can view the statistics information about TCP packets. The statistics information about TCP packets are divided into two major kinds which are Received packets and Sent packets.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands Closed connections: 0 (dropped: 0, initiated dropped: 0) 6.1.6 display tcp status Syntax display tcp status View Any view Parameter None Description Using display tcp status command, you can view the TCP connection state. Example # Display the state of all TCP connections. display tcp status TCPCB Local Add:port Foreign Add:port State 03e37dc4 0.0.0.0:4001 0.0.0.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands Description Using reset ip statistics command, you can reset the IP statistics information. For the related commands, see display ip interface vlan-interface, display ip statistics. Example # Reset the IP statistics information. reset ip statistics 6.1.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands Description Using tcp timer fin-timeout command, you can configure the TCP finwait timer. Using undo tcp timer fin-timeout command, you can restore the default value of the TCP finwait timer. When the TCP connection state changes from FIN_WAIT_1 to FIN_WAIT_2, the finwait timer is enabled.
Command Manual - Network Protocol Quidway S3000-EI Series Ethernet Switches Chapter 6 IP Performance Configuration Commands 6.1.11 tcp window Syntax tcp window window-size undo tcp window View System view Parameter window-size: The size of the transmission and receiving buffers measured in kilobytes (KB), whose value ranges from 1 to 32. By default, the window-size is 8KB.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual System Management Huawei Technologies Proprietary
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 File System Management Commands ....................................................................... 1-1 1.1 File System ........................................................................................................................ 1-1 1.1.1 cd.............................................................................................................................
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Table of Contents 1.4.11 ftp ........................................................................................................................ 1-23 1.4.12 get ....................................................................................................................... 1-23 1.4.13 lcd........................................................................................................................ 1-24 1.4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Table of Contents 4.1.2 clock summer-time .................................................................................................. 4-1 4.1.3 clock timezone......................................................................................................... 4-3 4.1.4 sysname .................................................................................................................. 4-3 4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Table of Contents 5.1.4 display snmp-agent mib-view.................................................................................. 5-3 5.1.5 display snmp-agent statistics .................................................................................. 5-4 5.1.6 display snmp-agent sys-info contact....................................................................... 5-5 5.1.7 display snmp-agent sys-info location ............
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Table of Contents 7.1.9 ntp-service broadcast-server................................................................................... 7-7 7.1.10 ntp-service max-dynamic-sessions ....................................................................... 7-8 7.1.11 ntp-service multicast-client.................................................................................... 7-8 7.1.12 ntp-service multicast-server .................
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Chapter 1 File System Management Commands 1.1 File System 1.1.1 cd Syntax cd directory View User view Parameter directory: Destination directory; By default, the directory is the working path configured by the user when the system starts. Description Using cd command, you can change the current user configuration path on the Ethernet Switch.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Description Using copy command, you can copy a file. When the destination filename is the same as that of an existing file, the system will ask whether to overwrite it. Example # Display current directory information. dir Directory of * 0 -rw- 595 Jul 12 2001 19:41:50 test.txt 16125952 bytes total (13975552 bytes free) # Copy the file test.txt and saves it as test.bak.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Note that, if two files with the same name in a directory are deleted, only the latest deleted file will be kept in the recycle bin. Example # Delete the file flash:/test/test.txt delete flash:/test/test.txt Delete flash:/test/test.txt?[Y/N]: 1.1.4 dir Syntax dir [ /all ] [ file-url ] View User view Parameter /all: Display all the files (including the deleted ones).
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands 7932928 bytes total (4966400 bytes free) # Display information about all the files (including the deleted files) in the directory flash:/test/ dir /all flash:/test/ Directory of flash:/test/ -rwxrwxrwx 1 noone nogroup 971 Sep 20 2003 14:28:52 test.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Example # Configure the prompt mode of file operation as quiet. [Quidway] file prompt quiet 1.1.6 format Syntax format filesystem View User view Parameter filesystem: Device name. Description Using format command, you can format the storage device. Format operation will cause non-recoverable loss of all the files on the device.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands The directory to be created cannot have the same name as that of other directory or file in the specified directory. Example # Create the directory dd. mkdir dd % Created dir dd 1.1.8 more Syntax more file-url View User view Parameter file-url: File name. Description Using more command, you can view content of specified file.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Parameter fileurl-source: Source file name. fileurl-dest: Destination file name. Description Using move command, you can move files. When the destination filename is the same as that of an existing file, the system will ask whether to overwrite it. Example # Display the current directory information.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Directory of flash:/test/ drwxrwxrwx 1 noone nogroup - Sep 20 2003 14:36:11 dd 7932928 bytes total (4963328 bytes free) 1.1.10 pwd Syntax pwd View User view Parameter none Description Using pwd command, you can view the current path. Error may occur without setting the current path. Example # Display the current path. pwd flash: 1.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Example # Display the current directory information. dir Directory of flash:/ drwxrwxrwx 1 noone -rwxrwxrwx 1 noone -rwxrwxrwx -rwxrwxrwx 1 noone 1 noone nogroup nogroup 971 nogroup nogroup 4 Jun 22 2002 02:19:16 Jun 30 2003 11:45:19 Aug 27 2003 16:56:56 2957562 Sep 20 2003 10:49:57 shit vrpcfg.txt snmpboots QX-S5516-VRP31 0-0030.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Description Using reset recycle-bin command, you can permanently delete files from the recycle bin. The delete command only puts the file into the recycle bin, but reset recycle-bin command will delete this file permanently. Example # Delete the file from the recycle bin. reset recycle-bin flash:/p1h_logic.out Clear flash:/plh_logic.out? [Y/N]: 1.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Parameter file-url: Name of the file to be recovered. Description Using undelete command, you can recover deleted file. The file name to be recovered cannot be the same as an existing directory name. If the destination file name is the same as an existing file name, prompt whether to overwrite.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands 1.2 Configuration File Management Commands 1.2.1 reset saved-configuration Syntax reset saved-configuration View User view Parameter none Description Using reset saved-configuration command, you can erase configuration files from the flash memory of the Ethernet Switch. Perform this command with cautious. It is suggested to consult technical support personnel first.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands View User view Parameter none Description Using save command, you can save the current configuration files to Flash memory. After finishing a group of configurations and achieving corresponding functions, user should remember to get the current configuration files stored in the flash memory.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Example # Display the configuration of FTP Server parameters. display ftp-server FTP server is running Max user number 5 User count 0 Timeout value(in minute) 30 1.3.2 display ftp-user Syntax display ftp-user View Any view Parameter none Description Using display ftp-user command, you can view the parameters of current FTP user.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Description Using ftp server command, you can start FTP Server and enable FTP user logon. Using undo ftp server command, you can close FTP Server and disable FTP user logon. By default, FTP Server is shut down. Perform this command to easily start or shut down FTP Server, preventing Ethernet Switch from being attacked by some unknown user. Example # Shut down FTP Server.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands 1.3.5 local-user Syntax local-user user-name undo local-user { user-name | all [ service-type { telnet | ftp | lan-access } ] } View System view Parameter user-name: Specifies a local username with a character string not exceeding 32 characters, excluding “/”, “:”, “*”, “?”, “<” and “>”. The @ character can only be used once in one username.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Parameter simple: Specifies to display passwords in simple text. cipher: Specifies to display passwords in cipher text. password: Defines a password, which is a character string of up to 16 characters if it is in simple text and of up to 24 characters if it is in cipher text. Description Using password command, you can configure a password display mode for local users.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Description Using service-type command, you can configure a service type for a particular user. Using undo service-type command, you can cancel the specified service type for the user. Example # Set to provide the lan-access service for the user huawei1. [Quidway-user-huawei1] service-type lan-access 1.4 FTP Client Commands 1.4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Parameter none Description Using binary command, you can configure file transmission type as binary mode. Example # Configure to transmit data in the binary mode. [ftp] binary 200 Type set to I. 1.4.3 bye Syntax bye View FTP Client view Parameter none Description Using bye command, you can disconnect with the remote FTP Server and return to user view.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Parameter pathname: Path name. Description Using cd command, you can change the working path on the remote FTP Server. This command is used to access another directory on FTP Server. Note that the user can only access the directories authorized by the FTP server. Example # Change the working path to flash:/temp [ftp] cd flash:/temp 1.4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Parameter none Description Using close command, user can disconnect FTP client side from FTP server side without exiting FTP client side view. That is to say, you can terminate the control connection and data connection with the remote FTP Server at the same time. Example # Terminate connection with the remote FTP Server and stays in FTP Client view. [ftp] close 1.4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Description Using delete command, you can cancel the specified file. This command is used to delete a file. Example # Delete the file temp.c [ftp] delete temp.c 1.4.9 dir Syntax dir [ filename ] [ localfile ] View FTP Client view Parameter filename: File name to be queried. localfile: Saved local file name. Description Using dir command, you can query a specified file.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Description Using disconnect command, subscribers can disconnect FTP client side from FTP server side without exiting FTP client side view. This command terminates the control connection and data connection with the remote FTP Server at the same time. Example # Terminate connection with the remote FTP Server and stays in FTP Client view. [ftp] disconnect 1.4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands remotefile: Name of a file on the remote FTP Server. Description Using get command, you can download a remote file and save it locally. If no local file name is specified, it will be considered the same as that on the remote FTP Server. Example # Download the file temp1.c and saves it as temp.c [ftp] get temp1.c temp.c 1.4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Description Using ls command, you can query a specified file. If no parameter is specified, all the files will be shown. Example # Query file temp.c [ftp] ls temp.c 1.4.15 mkdir Syntax mkdir pathname View FTP Client view Parameter pathname: Directory name. Description Using mkdir command, you can create a directory on the remote FTP Server.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Description Using open command, you can establish control connection with the remote FTP Server in the FTP Client view. Related command: close. Example # Establish control connection with the FTP Server, which IP address is 1.1.1.1. [ftp] open 1.1.1.1 Trying ... Press CTRL+K to abort Connected. 220220 WFTPD 2.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands 1.4.18 put Syntax put localfile [ remotefile ] View FTP Client view Parameter localfile: Local file name. remotefile: File name on the remote FTP Server. Description Using put command, you can upload a local file to the remote FTP Server. If the user does not specify the filename on the remote server, the system will consider it the same as the local file name by default.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands 1.4.20 quit Syntax quit View FTP Client view Parameter none Description Using quit command, you can terminate the connection with the remote FTP Server and return to user view. Example # Terminate connection with the remote FTP Server and returns to user view. [ftp] quit 1.4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands 1.4.22 rmdir Syntax rmdir pathname View FTP Client view Parameter pathname: Directory name of remote FTP Server. Description Using rmdir command, you can cancel the specified directory from FTP Server. Example # Delete the directory flash:/temp1 from FTP Server. [ftp] rmdir flash:/temp1 1.4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands undo verbose View FTP Client view Parameter none Description Using verbose command, you can enable verbose. Using undo verbose command, you can disable verbose. By default, verbose is enabled. Example # Enable verbose. [ftp]verbose 1.5 TFTP Configuration Commands 1.5.1 tftp Syntax tftp { ascii | binary } View System view Parameter ascii: Text format.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands [Quidway] tftp ascii 1.5.2 tftp get Syntax tftp get //A.A.A.A/xxx.yyy mmm.nnn View System view Parameter //A.A.A.A/xxx.yyy: Information about the file to be downloaded from the TFTP server. A.A.A.A: IP address of the TFTP server. mmm.nnn: Specify the filename saved as after downloaded to the switch, which can be different from xxx.yyy.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 1 File System Management Commands Description Using tftp put command, you can upload a file from the switch to the specified directory on the TFTP server (at A.A.A.A) and saving it as mmm.nnn. For the related commands, see tftp, tftp get. Example # Upload the vrpcfg.txt to the TFTP server at 1.1.3.214 and save it as Temp.txt. [Quidway] tftp ascii [Quidway] tftp put vrpcfg.txt //1.1.3.214/temp.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 2 MAC Address Table Management Commands Chapter 2 MAC Address Table Management Commands 2.1 MAC Address Table Management Commands 2.1.1 display mac-address aging-time Syntax display mac-address aging-time View Any view Parameter none Description Using display mac-address aging-time command, you can view the aging time of the dynamic entry in the MAC address table.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 2 MAC Address Table Management Commands Parameter mac-addr: Specify the MAC address. vlan-id: Specify the VLAN ID. static: Static table entry, lost after resetting switch. dynamic: Dynamic table entry, which will be aged. interface-type: Specify the interface type. interface-num: Specify the interface number. interface-name: Specify the interface name.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 2 MAC Address Table Management Commands Parameter static: Static table entry, lost after resetting switch. dynamic: Dynamic table entry, which will be aged. mac-addr: Specify the MAC address. interface-type: interface type; interface-num: interface number; interface-name: interface name; vlan-id: Specify the VLAN ID. Description Using mac-address command, you can add/modify the MAC address table entry.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 2 MAC Address Table Management Commands Parameter count: Specify the amount limit to the MAC addresses to be learned. 0 indicates that no address can be learned via the port. Description Using mac-address max-mac-count command, you can set a limit to the MAC addresses to be learned by the Ethernet port. Using undo mac-address max-mac-count command, you can cancel the limit.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 2 MAC Address Table Management Commands Too long or too short aging time set by subscribers will cause the problem that the Ethernet switch broadcasts a great mount of data packets without MAC addresses, which will affect the switch operation performance. If aging time is set too long, the Ethernet switch will store a great number of out-of-date MAC address tables.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 3 Device Management Commands Chapter 3 Device Management Commands 3.1 Device Management Commands 3.1.1 boot boot-loader Syntax boot boot-loader file-url View User view Parameter file-url: Path and name of APP file. Description Using boot boot-loader command, you can configure the app file used for boot of the next time. Example # Specify the APP application used for boot of next time.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 3 Device Management Commands Example # Upgrade bootrom. boot bootrom PLATV100R002B09D002.btm 3.1.3 display boot-loader Syntax display boot-loader View Any view Parameter none Description Using display boot-loader command, you can view APP file used next time. Example # View APP file used next time. display boot-loader The app to boot at the next time is: PLATV100R002B09D002.APP 3.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 3 Device Management Commands 18% in last 5 seconds 19% in last 1 minute 19% in last 5 minutes Table 3-1 Display information Field Description CPU busy status. The busy status of switch 18% in last 5 seconds The CPU occupancy rate is 18% at last 5 seconds 19% in last 1 minute The CPU occupancy rate is 19% at last 1 minute 19% in last 5 minutes The CPU occupancy rate is 19% at last 5 minutes 3.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 3 Device Management Commands Table 3-2 Output description of the display device command Field Description SlotNo Physical card number SubSNo Sub physical card number (namely stack card number) PortNum Number of ports PCBVer PCB version number FPGAVer FPGA version number CPLDVer r Hardware version number BootRomVer BootROM software version number AddrLM Address learning mode Type Interface card type 3.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 3 Device Management Commands 3.1.7 display fan Syntax display fan [ fan-id ] View Any view Parameter fan-id: the fan ID. Description Using display fan command, you can view the working state of the built-in fans. User can Perform this command to see if they work normally. Example # Display the working state of the fans.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 3 Device Management Commands System Total Memory(bytes): 32491008 Total Used Memory(bytes): 13181348 Used Rate: 40% Table 3-3 Display information Field Description System Total Memory(bytes) The Total Memory of switch, unit in byte Total Used Memory(bytes) The Total used Memory of switch, unit in byte Used Rate The memory used rate 3.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 3 Device Management Commands Description Using reboot command, you can reset the Ethernet Switch when failure occurs. Example # Reboots the Switch. reboot 3.1.11 temperature-limit Syntax temperature-limit slot down-value up-value undo temperature-limit slot View User view, system view Parameter slot: Physical card number. down-value: Lower temperature limit. up-value: Upper temperature limit.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands Chapter 4 System Maintenance Commands 4.1 Basic System Configuration and Management Commands 4.1.1 clock datetime Syntax clock datetime HH:MM:SS YYYY/MM/DD View User view Parameter HH:MM:SS: Current clock. HH ranges from 0 to 23. MM and SS range from 0 to 59. YYYY/MM/DD: Specify the current year, month and date. YYYY ranges from 1993 to 2035.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands View User view Parameter zone_name: Name of the summer time, which is a character with the length ranging 1 to 32. one-off: Only set the summer time of a certain year. repeating: Set the summer time of every year starting from a certain year. start-time: Set start time of the summer time, input like HH:MM:SS (hour/minute/second).
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands 4.1.3 clock timezone Syntax clock timezone zone_name { add | minus } HH:MM:SS undo clock timezone View User view Parameter zone_name: Name of the time zone, which is a character with the length ranging 1 to 32. add: The time is adding compared with the UTC. minus: The time is minus compared with the UTC. HH:MM:SS: Time (hour/minute/second).
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands Parameter sysname: Specify the hostname with a character string with the length ranging from1 to 30 characters. Description Using sysname command, you can configure the hostname of Ethernet Switch. By default, the hostname of Ethernet Switch is Quidway. Changing the hostname name of Ethernet Switch will affect the prompt of command line interface. E.g.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands 4.2.2 display current-configuration Syntax display current-configuration [ controller | interface interface-type [ interface-number ] | configuration [ post-system | system | user-interface ] ] [ | { begin | exclude | include } regular-expression ] View Any view Parameter controller: View the configuration information of controllers.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands For the related command, see save, reset saved-configuration and display saved-configuration. Example # View the running configuration parameters of the switch. display current-configuration # sysname S3026C # radius scheme system server-type nec primary authentication 127.0.0.1 1645 primary accounting 127.0.0.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands # interface Ethernet0/7 # interface Ethernet0/8 # interface Ethernet0/9 # interface Ethernet0/10 # interface Ethernet0/11 # interface Ethernet0/12 # interface Ethernet0/13 # interface Ethernet0/14 # interface Ethernet0/15 # interface Ethernet0/16 # interface Ethernet0/17 # interface Ethernet0/18 # interface Ethernet0/19 # interface Ethernet0/20 # interface Ethernet0/21 # interface Ethernet0/2
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands # View the lines containing the character string “10*” in the configuration information. The “*” indicates that the “0” before it can appear 0 times or multiple consecutive times. display current-configuration | include 10* primary authentication 127.0.0.1 1645 primary accounting 127.0.0.1 1646 local-server nas-ip 127.0.0.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands domain default enable system # local-server nas-ip 127.0.0.1 key nec # vlan 1 # user-interface aux 0 user-interface vty 0 4 # return 4.2.3 display debugging Syntax display debugging [ interface { interface-name | interface-type interface-num } ] [ module-name ] View Any view Parameter interface-name: Specify the Ethernet port name. interface-type: Specify the Ethernet port type.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands View Any view Parameter none Description Using display saved-configuration command, you can view the configuration files in the flash memory of Ethernet Switch. If the Ethernet Switch works abnormally after electrified, execute the display saved-configuration command to view the startup configuration of the Ethernet Switch.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands vlan 1 # interface Ethernet0/1 # interface Ethernet0/2 # interface Ethernet0/3 # interface Ethernet0/4 # interface Ethernet0/5 # interface Ethernet0/6 # interface Ethernet0/7 # interface Ethernet0/8 # interface Ethernet0/9 # interface Ethernet0/10 # interface Ethernet0/11 # interface Ethernet0/12 # interface Ethernet0/13 # interface Ethernet0/14 # interface Ethernet0/15 # interface Ethernet0/
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands # interface Ethernet0/22 # interface Ethernet0/23 # interface Ethernet0/24 # interface NULL0 # user-interface aux 0 user-interface vty 0 4 # return 4.2.5 display users Syntax display users [ all ] View Any view Parameter all: display all users connected to the switch. Description Using display users command, you can view information about users connected to the switch.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands Parameter none Description Using display version command, you can view such information as software version, issue date and the basic hardware configurations. Example # Display the information about the system version. display version Versatile Routing Platform Software VRP (R) Software, Version 3.10, RELEASE 0014 Copyright (c) Reserved.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands Description Using debugging command, you can enable the system debugging. Using undo debugging command, you can disable the system debugging. By default, all the debugging processes are disabled. Ethernet Switch provides various kinds of debugging functions for technical support personnel and experienced maintenance staff to troubleshoot the network.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands Example # Display all system configuration information display diagnostic-information This operation may take a few minutes, continue?[Y/N]y ---------------display clock--------------20:12:39 UTC Mon 2000/5/8 ---------------display version--------------Huawei Versatile Routing Platform Software VRP (tm) software, Version 3.10 Copyright (c) 2000-2002 HUAWEI TECH CO., LTD. 4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands -q: Configure not to display any other detailed information except statistics. -r: Record route. -s packetsize: Specify the length of ECHO-REQUEST (excluding IP and ICMP packet header) in bytes. -t timeout: Maximum waiting time after sending the ECHO-REQUEST (measured in ms). -tos tos: Specify TOS value for echo requests to be sent, range from 0 to 255.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches z Chapter 4 System Maintenance Commands The final statistics, including number of sent packets, number of response packets received, percentage of non-response packets and minimal/maximum/average value of response time. If the network transmission rate is too low, you can increase the response message timeout. For the related commands, see tracert. Example # Check whether the host 202.38.160.244 is reachable.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands -w: Configure to verify the -wf switch, timeout is an integer specifying IP packet timeout in seconds, larger than 0. string: IP address of the destination host or the hostname of the remote system. Description Using tracert command, you can check the reachability of network connection and troubleshoot the network.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands 12 * * * 13 128.121.54.72 (128.121.54.72) 259 ms 499 ms 279 ms 14 * * * 15 * * * 16 * * * 17 * * * 18 ALLSPICE.LCS.MIT.EDU (18.26.0.115) 339 ms 279 ms 279 ms 4.5 Log Commands 4.5.1 display channel Syntax display channel [ channel-number | channel-name ] View Any view Parameter channel-number: Channel number, ranging from 0 to 9, that is, the system has ten channels.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands View Any view Parameter None Description Using display info-center command, you can view the configuration of system log and the information recorded in the memory buffer. If the information in the current log/trap buffer is less than the specified sizeval, display the actual log/trap information.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands 4.5.3 info-center channel name Syntax info-center channel channel-number name channel-name View System view Parameter channel-number: Channel number, ranging from 0 to 9, that is, system has ten channels. channel-name: Specify the channel name with a character string not exceeding 30 characters, excluding "-", "/" or "\". .
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands Description Using info-center console channel command, you can configure the channel through which the log information is output to the console. By default, Ethernet switches do not output log information to the console. This command takes effect only after system logging is started. For the related commands, see info-center enable,display info-center.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands 4.5.6 info-center logbuffer Syntax info-center logbuffer [ channel { channel-number | channel-name } ] [ size buffersize ] undo info-center logbuffer [ channel | size ] View System view Parameter channel: Configure the channel to output information to buffer. channel-number: Channel number, ranging from 0 to 9, that is, system has ten channels. channel-name: Specify the channel name.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands View System view Parameter host-ip-addr: IP address of info-center loghost. channel: Configure information channel of the info-center loghost. channel-number: Channel number, ranging from 0 to 9, that is, system has ten channels. channel-name: Specify the channel name. The name can be channel6, channel7, channel8, channel9, console, logbuffer, loghost, monitor, snmpagent, trapbuffer.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands Parameter source interface-name: set source address of the packets sent to loghost as the address of the interface specified by the interface-name. Normally, the interface should be VLAN interface. Description Using info-center loghost source command, you can set source address of the packets sent to loghost as the address of the interface specified by the interface-name.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands This command takes effect only after system logging is started. For the related commands, see info-center enable,display info-center. Example # Configure channel 0 to output log information to user terminal. [Quidway] info-center monitor channel 0 4.5.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands View System view Parameter modu-name: Module name. default: All the modules. log: Log information. trap: Trap information. debugging: Debugging information. level: Level. severity: Information level, do not output information below this level. Information at different levels is as follows: emergencies: Level 0 information, which cannot be used by the system.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands specified channels. You can configure the channels in the output direction, channel filter information, filtering and redirecting of all kinds of information.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands debugging: Debugging information. logging: Log information. trapping: Trap information. Description Using info-center switch-on command, you can turn on the information synchronization switch of the specified switch. Using undo info-center switch-on command, you can turn off the information synchronization switch of the specified switch.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands none: No timestamp format. Description Using info-center timestamp command, you can configure the timestamp output format in debugging/trap information. Using undo info-center timestamp command, you can disable the output of timestamp field. By default, datetime stamp is used. Example # Configure the debugging information timestamp format as boot.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands [Quidway] info-center trapbuffer size 30 4.5.15 reset logbuffer Syntax reset logbuffer View User view Parameter none Description Using reset logbuffer command, you can reset information in log buffer. Example # Clear information in log buffer. reset logbuffer 4.5.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands undo terminal debugging View User view Parameter none Description Using terminal debugging command, you can configure to display the debugging information on the terminal. Using undo terminal debugging command, you can configure not to display the debugging information on the terminal. By default, the displaying function is disabled. For the related commands, see debugging.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands 4.5.19 terminal monitor Syntax terminal monitor undo terminal monitor View User view Parameter none Description Using terminal monitor command, you can enable the log debugging/log/trap on the terminal monitor. Using undo terminal monitor command, you can disable these functions. By default, enable these functions for the console user and disable them for the terminal user.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 4 System Maintenance Commands Parameter none Description Using terminal trapping command, you can enable terminal trap information display. Using undo terminal trapping command, you can disable this function. By default, this function is enabled. Example # Enable trap information display.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands Chapter 5 SNMP Configuration Commands 5.1 SNMP Configuration Commands 5.1.1 display snmp-agent community Syntax display snmp-agent community [ read | write ] View Any view Parameter read: display read-only community information. write: display read-write community information. Description Using display snmp-agent community command, you can view the currently configured community names.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands Parameter local-engineid: local engine ID. remote-engineid: remote engine ID. Description Using display snmp-agent engineid command, you can view engine ID of current device. SNMP engine is the core of SNMP entity. It performs the function of sending, receiving and authenticating SNMP message, extracting PDU, packet encapsulation and the communication with SNMP application, etc.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands The following table describes the output fields.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches View name:ViewDefault Storage-type: nonVolatile View name:ViewDefault Storage-type: nonVolatile View name:ViewDefault Storage-type: nonVolatile View name:ViewDefault Storage-type: nonVolatile Chapter 5 SNMP Configuration Commands MIB Subtree:internet -included active MIB Subtree:snmpUsmMIB -excluded active MIB Subtree:snmpVacmMIB -excluded active MIB Subtree:snmpModules.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands Description Using display snmp-agent statistics command, you can view current state of SNMP communication. This command provides a counter for SNMP operations. Example # Display the current state of SNMP communication.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands Example # Display the character string sysContact (system contact). display snmp-agent sys-info contact The contact person for this managed node: Mr.Wang-Tel:3306 5.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands Example # Display the version information of running SNMP display snmp-agent sys-info version SNMP version running in the system: SNMPv3 5.1.9 display snmp-agent usm-user Syntax display snmp-agent usm-user [ engineid engineid ] [ group groupname ] [ username username ] View Any view Parameter engineid: display user information with specified engine ID.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands 5.1.10 snmp-agent local-engineid Syntax snmp-agent local-engineid engineid undo snmp-agent local-engineid View System view Parameter local-engineid: Specify an engineID for the local SNMPv3 entity engineid: Specify the engine ID with a character string, only composed of hexadecimal numbers between 5 and 32 including; By default, the value is "Enterprise Number + device information".
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands community-name: Community name character string. view-name: MIB view name. acl acl-list:set access control list for specified community. Description Using snmp-agent community command, you can configure community access name and enable the access to SNMP. Using undo snmp-agent community command, you can cancel the settings of community access name.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands notifyview: Specify the notify view name, ranging from 1 to 32 bytes. acl acl-list:Set access control list for this group name. Description Using snmp-agent group command, you can configure a new SNMP group, that is, to map SNMP user to SNMP view. Using undo snmp-agent group command, you can cancel a specified SNMP group.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands Both the character string of OID and the node name can be input as parameter. Example # Create a view that consists of all the objects of MIB-II. [Quidway] snmp-agent mib-view included mib2 5.6.1.3 5.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands Parameter sysContact: Specify a character string describing the system maintaining contact (in bytes), with a length ranging from 1 to 255; By default, the contact information is "HuaWei Beijing China". sysLocation: Specify a character string to describe the system location; By default, the character string is "Beijing China". version: version of running SNMP.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands udp-domain:Specify transport domain over UDP for the target address host-addr: IP address of destination host. udp-port udp-port-number: Specify the UDP port number of the host to receive the SNMP notification. params:Specify SNMP target information to be used in the generation of SNMP messages v1: Represent the version of SNMPV1. v2c: Represent the version of SNMPV2C.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands undo snmp-agent trap enable [ standard [ authentication ] [ coldstart ] [ linkdown ] [ linkup ] [ warmstart ] ] View System view Parameter standard [ authentication ] [ coldstart ] [ linkdown ] [ linkup ] [ warmstart ]: Configure to send standard Trap messages. authentication: Configure to send SNMP authentication Trap messages. coldstart: Configure to send SNMP cold start Trap messages.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands Parameter seconds: Specify the timeouts, ranging from 1 to 2592000 seconds; By default, the timeout interval is 120 seconds. Description Using snmp-agent trap life command, you can configure the timeout of Trap packets. Using undo snmp-agent trap life command, you can restore the default value. The set timeout of Trap packet is represented by seconds.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands 5.1.20 snmp-agent trap source Syntax snmp-agent trap source vlan-interface vlan-id undo snmp-agent trap source View System view Parameter vlan-id: Specify the VLAN interface ID, ranging from 1 to 4000. Description Using snmp-agent trap source command, you can configure the source address for sending Trap.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands v3: Configure to use V3 safe mode. authentication-mode: Specify the safety level as authentication required. md5: MD5 algorithm is adopted in authentication. MD5 authentication uses the 128-digit password. Computation speed of MD5 is faster than that of SHA sha: SHA algorithm is adopted in authentication. SHA authentication uses the 160-digit password.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 5 SNMP Configuration Commands Description Using undo snmp-agent command, you can disable all versions of SNMP running on the server. Perform any command of snmp-agent will enable SNMP Agent. Example # Disable the running SNMP agents of all SNMP versions.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands Chapter 6 RMON Configuration Commands 6.1 RMON Configuration Commands 6.1.1 display rmon alarm Syntax display rmon alarm [ alarm-table-entry ] View Any view Parameter alarm-table-entry: Alarm table entry index. Description Using display rmon alarm command, you can view RMON alarm information. For the related commands, see rmon alarm. Example # Display the RMON alarm information.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands Field Description Rising threshold Rising threshold. When sampling value rises from normal value to this threshold, rising threshold alarm will be triggered. Falling threshold Falling threshold. When sampling value decreases from normal value to this threshold, falling threshold alarm will be triggered.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands Table 6-2 Output description of the display rmon event command Field Description Event table 1 Index 1 in event table HUAWEI Owner VALID The entry corresponding to the index is valid Description Event description Will cause log-trap when triggered, last triggered at 0days 00h:02m:27s When the event is triggered, it will cause the log-trap.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands Table 6-3 Output description of the display rmon eventlog command Field Description Event table 1 Index 1 in event table HUAWEI Owner VALID The entry corresponding to the index is valid Description Event description less than(or =) 100 with alarm value 0 The alarm sample value is less than or equal to 100 Alarm sample type is absolute The type of alarm sampling is absolute Gener
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands fragments :0 , jabbers :0 collisions :0 , utilization :0 Table 6-4 Output description of the display rmon history command Field Description History control entry Index number in history control table HUAWEI Owner VALID The entry corresponding to the index is valid Samples interface The sampled interface Sampling interval Sampling interval buckets Records in history contro
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands Description Using display rmon prialarm command, you can view information about extended alarm table. For the related commands, see rmon prialarm. Example # display alarm information about extended RMON. display rmon prialarm Prialarm table 1 owned by HUAWEI is VALID. Samples absolute value : 1.3.6.1.2.1.16.1.1.1.4.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands 6.1.6 display rmon statistics Syntax display rmon statistics [ port-num ] View Any view Parameter port-num: Ethernet port number. Description Using display rmon statistics command, you can view RMON statistics.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands Field Description packets Packets received/sent in sampling time broadcast packets Number of broadcast packets multicast packets Number of multicast packets undersized packets Number of undersized packets oversized packets Number of oversized packets fragments packets Number of undersized and CRC error packets jabbers Number of oversized and CRC error packets CRC alignment err
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands event-entry2: Event number corresponding to the falling threshold, ranging from 0 to 65535. owner text: Specifies the creator of the alarm. Length of the character string ranges from 1 to 127. Description Using rmon alarm command, you can add an entry to the alarm table. Using undo rmon alarm command, you can cancel an entry from this table.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands Description Using rmon event command, you can add an entry to the event table. Using undo rmon event command, you can cancel an entry from this table. Event management of RMON defines the way to deal with event number and event-log, send trap message or log while sending trap message.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands 6.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 6 RMON Configuration Commands Example # Delete line 10 from the extended RMON alarm table. [Quidway] undo rmon prialarm 10 6.1.11 rmon statistics Syntax rmon statistics entry-number [ owner text-string ] undo rmon statistics entry-number View Ethernet port view Parameter entry-number: Number of the entry to be added/deleted, ranging from 1 to 65535. owner text-string: Creator of the entry.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands Chapter 7 NTP Configuration Commands 7.1 NTP Configuration Commands 7.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands Example # Enable NTP access control debugging. debugging ntp-service access 7.1.2 display ntp-service sessions Syntax display ntp-service sessions [ verbose ] View Any view Parameter verbose: Indicate to display the detail information about the sessions.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands Parameter None Description Using command display ntp-service status, you can display the NTP service status. Example # Display the NTP service status. display ntp-service status clock status: unsynchronized clock stratum: 16 reference clock ID: none nominal frequency: 100.0000 Hz actual frequency: 100.0000 Hz clock precision: 2^17 clock offset: 0.0000 ms root delay: 0.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands 7.1.4 display ntp-service trace Syntax display ntp-service trace [ ip-address ] View Any view Parameter ip-address: Specify the IP address of the NTP server serving as the reference clock source. Description Using display ntp-service trace command, you can display the brief information about every NTP server on the way from the local equipment to the reference clock source.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands Description Using ntp-service access command, you can set the authority to access the local equipment. Using undo ntp-service access command, you can cancel the access authority settings. By default, there is no limit to the access. Set authority to access the NTP services on a local Ethernet Switch. This is a basic and brief security measure, compared to authentication.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands 7.1.7 ntp-service authentication-keyid Syntax ntp-service authentication-keyid number authentication-mode md5 value undo ntp-service authentication-keyid number View System view Parameter number: Specify the key number and range from 1 to 4294967295. value: Specify the value of the key with 1 to 32 ASCII characters.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands Description Using ntp-service broadcast-client command, you can configure NTP broadcast client mode. Using undo ntp-service broadcast-client command, you can disable the NTP broadcast client mode. By default, the NTP broadcast client mode is disabled. Designate an interface on the local Ethernet Switch to receive NTP broadcast messages and operate in broadcast client mode.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands Designate an interface on the local equipment to broadcast NTP packets. The local equipment runs in broadcast-server mode and regularly broadcasts packets to its clients. Example # Configure to broadcast NTP packets via Vlan-Interface1 and encrypt them with Key 4 and set the NTP version number as 3.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands Parameter ip-address: Specify an multicast IP address of Class D. Description Using ntp-service multicast-client command, you can configure the NTP multicast client mode. Using undo ntp-service multicast-client command, you can disable the NTP multicast client mode. By default, the multicast client service is disabled. ip-address defaults to 224.0.1.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands number: Specify NTP version number and range from 1 to 3. Description Using ntp-service multicast-server command, you can configure NTP multicast server mode, if no IP address is specified, switch automatically choice the 224.0.1.1 as the multicast IP address.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands You can use this command to designate an NTP external reference clock or the local clock as an NTP master clock to provide synchronized time for other equipment. ip-address specifies the IP address of an external clock as 127.127.t.u. If no IP address is specified, the local clock is set as the NTP master clock by default. You can also specify the stratum of the NTP master clock.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands 7.1.15 ntp-service source-interface Syntax ntp-service source-interface { interface-name | interface-type interface-number } undo ntp-service source-interface View System view Parameter interface-name: Specify an interface. The source IP address of the packets will be taken from the address of the interface.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands Parameter None Description Using ntp-service in-interface disable command, you can disable an interface to receive NTP message. Using undo ntp-service in-interface disable command, you can enable an interface to receive NTP message. By default, an interface is enabled to receive NTP message. Example # Disable Vlan-Interface1 to receive NTP message.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands priority: Designate a server as the first choice. Description Using ntp-service unicast-peer command, you can configure NTP peer mode. Using undo ntp-service unicast-peer command, you can cancel NTP peer mode. By default, version number number defaults to 3, the authentication is disabled, and the local server is not the first choice.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 7 NTP Configuration Commands interface-name: Specify the interface name. When a local device sends an NTP message to a peer, the source IP address of the message is taken from the address of the interface. interface-type: Specify the interface type and determine an interface together with the interface-number parameter.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands Chapter 8 SSH Configuration Commands 8.1 SSH Configuration Commands 8.1.1 debugging rsa Command debugging rsa undo debugging rsa View User view Parameter None Description Using the debugging rsa command, you can send the detailed information of RSA algorithm, including every process and packet structure, to the information center as debugging information.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands Parameter all: All SSH channels index: Debugged SSH channels. Optional values depend on the VTY number and they are 0~4. Description Using the debugging ssh server command, you can send the negotiation process defined in SSH1.5 protocol to the information center as debugging information and debug a single user interface.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands Description Using the display rsa local-key-pair public command, you can display local key pair and public key of the server. If no key is generated, corresponding information will be prompted, for example, “RSA keys not found”. For the related command, see rsa local-key-pair create. Example # Display local key pair and public key of the server.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands Example # Display a designated RSA public key.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands SSH server key generating interval : 1 hours SSH Authentication retries : 3 times # Display SSH sessions. [Quidway] display ssh server session Connection Version Encryption State Username VTY0 1.5 DES Session started Quidway VTY3 1.5 DES Session started router 8.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands Parameter None Description Using the peer-public-key end command, you can finish editing peer public key and quit from RSA public key view to system view. For the related commands, see rsa peer-public-key, public-key-code end. Example # Quit RSA public key view. [Quidway] rsa peer-public-key quidway003 [Quidway-rsa-public-key] peer-public-key end [Quidway] 8.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands Example # Disable Telnet on vty0 through vty4, only SSH available. [Quidway] user-interface vty 0 4 [Quidway-ui-vty0-4] protocol inbound ssh # Disable Telnet on vty0, only SSH available. [Quidway] user-interface vty 0 [Quidway-ui-vty0] protocol inbound ssh 8.1.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands 8.1.10 public-key-code end Command public-key-code end View RSA key code view Parameter None Description Using the public-key-code end command, you can save the configured public key and return to the RSA public key view from the RSA key code view. This command terminates the edit process of public key and checks its validity before saving.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands name plus server and switch name plus host, for example, Quidway_host and Quidway_server. The configuration result of this command will not be stored in the configuration file. The system prompts you to key in bit range, for which, the server key pair must be at least 128 bits longer than the host key pair. The maximum bit range of both key pairs is 2048 bits and the minimum is 512.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands Description Using the rsa local-key-pair destroy command, you can remove all RSA key pairs at the server, including Host key pair and Server key pair. Acknowledgement information will be promoted before the system clears all RSA key pairs. This command is just a one-time instruction, so the result will not be stored in the configuration file.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands 8.1.14 ssh server authentication-retries Command ssh server authentication-retries times undo ssh server authentication-retries View System view Parameter times: Specifies authentication retry times, in the range of 1~5. Description Using the ssh server authentication-retries command, you can define SSH authentication retry times value, which takes effect at next logon.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands For the related commands, see display ssh server. Example # Define update interval of server key pair as 3 hours. [Quidway] ssh server rekey-interval 3 [Quidway] 8.1.16 ssh server timeout Command ssh server timeout seconds undo ssh server timeout View System view Parameter seconds: Defines registration timeout value, in the range of 1~120 seconds.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands username: Valid local user name or user name defined by remote RADIUS system. Description Using the ssh user username assign rsa-key command, you can associate an existing public key with a designated user. Using the undo ssh user username assign rsa-key command, you can delete the association.
Command Manual - System Management Quidway S3000-EI Series Ethernet Switches Chapter 8 SSH Configuration Commands Example # Specify zhangsan’s authentication type as password.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual Remote Power-feeding Huawei Technologies Proprietary
Command Manual - Remote Power-feeding Quidway S3000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 Remote Power-feeding Configuration Commands .................................................. 1-1 1.1 Remote Power-feeding Configuration Commands ............................................................ 1-1 1.1.1 display poe interface ............................................................................................... 1-1 1.1.2 display poe interface power ..........
Command Manual - Remote Power-feeding Quidway S3000-EI Series Ethernet Switches Chapter 1 Remote Power-feeding Configuration Commands Chapter 1 Remote Power-feeding Configuration Commands 1.1 Remote Power-feeding Configuration Commands 1.1.1 display poe interface Syntax display poe interface { interface-name | interface-type interface-num | all } View Any view Parameter interface-name | interface-type interface-num: Port of the switch, for detailed description, please refer to Command Manual – Port.
Command Manual - Remote Power-feeding Quidway S3000-EI Series Ethernet Switches Chapter 1 Remote Power-feeding Configuration Commands 1.1.2 display poe interface power Syntax display poe interface power { interface-name | interface-type interface-num | all } View Any view Parameter interface-name | interface-type interface-num: Port of the switch, for detailed description, please refer to Command Manual – Port. all: view the power of all ports.
Command Manual - Remote Power-feeding Quidway S3000-EI Series Ethernet Switches Chapter 1 Remote Power-feeding Configuration Commands Ethernet0/23 current power : 0 mw Ethernet0/24 current power : 0 mw 1.1.3 display poe powersupply Syntax display poe powersupply View Any view Parameter None. Description Using the display poe powersupply command, you can view the PoE parameters of PSE power supply device. Example # Display the PoE parameters of PSE power supply device.
Command Manual - Remote Power-feeding Quidway S3000-EI Series Ethernet Switches Chapter 1 Remote Power-feeding Configuration Commands Parameter None Description Using the poe disable command, you can disable remote power-feeding on a port. Using the undo poe disable command, you can restore the default value. By default, a port is enabled to perform remote power-feeding. Example # Disable Ethernet0/1 to perform remote power-feeding. [Quidway-Ethernet0/1] poe disable 1.1.
Command Manual - Remote Power-feeding Quidway S3000-EI Series Ethernet Switches Chapter 1 Remote Power-feeding Configuration Commands 1.1.6 poe max-power Syntax poe max-power max-power undo poe max-power View Ethernet port view Parameter max-power: The maximum power supplied by a port, ranging from 100 to 15400 milliwatt. Description Using the poe max-power command, you can configure the maximum power supplied by a port. By default, a port supplies power under a maximum of 15400 milliwatt.
Command Manual - Remote Power-feeding Quidway S3000-EI Series Ethernet Switches Chapter 1 Remote Power-feeding Configuration Commands By default, a port supplies power through signal lines. Example # Configure the current port Ethernet0/1 to supply power through signal lines. [Quidway-Ethernet0/1] poe mode signal 1.1.8 poe power-management Syntax poe power-management { auto | manual } undo poe power-management View System view Parameter auto: auto power management mode.
Command Manual - Remote Power-feeding Quidway S3000-EI Series Ethernet Switches Chapter 1 Remote Power-feeding Configuration Commands [Quidway] poe power-management auto 1.1.9 poe priority Syntax poe priority { critical | high | low } undo poe priority View Ethernet port view Parameter critical: The power supply priority of the port is critical. high: The power supply priority of the port is high. low: The power supply priority of the port is low.
Command Manual - Remote Power-feeding Quidway S3000-EI Series Ethernet Switches Chapter 1 Remote Power-feeding Configuration Commands PoE function relies on the PoE daughter-card inside the switch. User can use this command to upgrade the application of PoE daughter-card, and the switch service is not interruptive during this process. The extent name of the application file should be “bin”. Example # use file “flash:/new.bin” to upgrade the PoE daughter-card. [Quidway] poe update flash:/new.bin 1.1.
HUAWEI Quidway S3000-EI Series Ethernet Switches Command Manual Appendix Huawei Technologies Proprietary
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index Appendix A Command Index The command index includes all the commands in the Command Manual, which are arranged alphabetically.
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index boot bootrom System Management 3-1 broadcast-suppression Port 1-1 build Integrated Management 2-16 bye System Management 1-19 cd System Management 1-1 cd System Management 1-19 cdup System Management 1-20 check region-configuration STP 1-1 clock datetime System Management 4-1 clock summer-time System Management 4-1 clock timezone System Management 4-3 close System Management 1-20
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index debugging gmrp Multicast 1-1 debugging ntp-service System Management 7-1 debugging rsa System Management 8-1 debugging ssh server System Management 8-1 delete System Management 1-2 delete System Management 1-21 delete-member Integrated Management 2-19 description Getting Started 2-1 description Port 1-1 description VLAN 1-1 dhcp-snooping Network Protocol 2-1 dhcp-snooping trust Ne
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index display debugging System Management 4-9 display debugging habp Security 3-1 display device System Management 3-3 display dhcp client Network Protocol 3-1 display dhcp-snooping Network Protocol 2-2 display dhcp-snooping count Network Protocol 2-3 display dhcp-snooping trust Network Protocol 2-3 display diagnostic-information System Management 4-14 display domain Security 2-5 display dot1x
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index display ip routing-table Getting Started 2-4 display ip routing-table acl Getting Started 2-5 display ip routing-table ip_address Getting Started 2-9 display ip routing-table ip_address1 ip_address2 Getting Started 2-11 display ip routing-table ip-prefix Getting Started 2-12 display ip routing-table protocol Getting Started 2-13 display ip routing-table radix Getting Started 2-14 display ip ro
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index display power System Management 3-6 display qos cos-local-precedence-map QoS/ACL 2-1 display qos-global all QoS/ACL 2-1 display qos-global mirrored-to QoS/ACL 2-3 display qos-global traffic-priority QoS/ACL 2-4 display qos-global traffic-redirect QoS/ACL 2-5 display qos-global traffic-statistic QoS/ACL 2-6 display qos-interface all QoS/ACL 2-7 display qos-interface line-rate QoS/ACL 2-9
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index display stacking Integrated Management 1-1 display stop-accounting-buffer Security 2-24 display stp STP 1-3 display stp region-configuration STP 1-5 display tcp statistics Network Protocol 6-6 display tcp status Network Protocol 6-8 display time-range QoS/ACL 1-4 display user-interface Getting Started 1-5 display users Getting Started 1-6 display users System Management 4-12 display v
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index F file prompt System Management 1-4 flow-constrain Port 1-7 flow-constrain method Port 1-8 flow-control Getting Started 1-7 flow-control Port 1-9 flow-interval Port 1-9 format System Management 1-5 free user-interface Getting Started 1-7 ftp System Management 1-23 ftp server System Management 1-14 ftp timeout System Management 1-15 ftp-server Integrated Management 2-25 garp time
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index idle-cut Security 2-9 idle-timeout Getting Started 1-10 igmp-snooping Multicast 2-4 igmp-snooping fast-leave Multicast 2-5 igmp-snooping group-limit Multicast 2-5 igmp-snooping group-policy Multicast 2-6 igmp-snooping host-aging-time Multicast 2-8 igmp-snooping max-response-time Multicast 2-8 igmp-snooping router-aging-time Multicast 2-9 info-center channel name System Management 4-21
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index isolate-user-vlan enable VLAN 2-3 isolate-user-vlan igsp enable VLAN 2-4 Security 2-25 language-mode Getting Started 1-11 lcd System Management 1-24 line-rate QoS/ACL 2-11 link-aggregation Port 2-2 local-server Security 2-26 local-user Security 2-10 local-user System Management 1-16 local-user password-display-mode Security 2-11 lock Getting Started 1-11 logging-host Integrated
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index mkdir System Management 1-5 mkdir System Management 1-25 more System Management 1-6 move System Management 1-6 multicast-source-deny Multicast 2-10 name Security 2-12 nas-ip Security 2-27 ndp enable Integrated Management 2-4 ndp timer aging Integrated Management 2-5 ndp timer hello Integrated Management 2-5 ntdp enable Integrated Management 2-9 ntdp explore Integrated Management
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index ntp-service source-interface System Management 7-12 ntp-service unicast-peer System Management 7-13 ntp-service unicast-server System Management 7-14 System Management 1-25 packet-filter QoS/ACL 1-5 parity Getting Started 1-12 passive System Management 1-26 password Security 2-13 password System Management 1-16 peer-public-key end System Management 8-5 ping System Management 4-15 po
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index port-tagged Integrated Management 2-28 primary accounting Security 2-28 primary authentication Security 2-29 priority QoS/ACL 2-13 priority trust QoS/ACL 2-14 protocol inbound Getting Started 1-13 protocol inbound System Management 8-6 public-key-code begin System Management 8-7 public-key-code end System Management 8-8 put System Management 1-27 pwd System Management 1-8 pwd Syst
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index reset igmp-snooping statistics Multicast 2-11 reset ip statistics Network Protocol 6-8 reset logbuffer System Management 4-31 reset ndp statistics Integrated Management 2-6 reset poe-configuration Remote Power-feeding 1-8 reset radius statistics Security 2-32 reset recycle-bin System Management 1-9 reset saved-configuration System Management 1-12 reset stop-accounting-buffer Security 2-32
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index secondary accounting Security 2-36 secondary authentication Security 2-36 self-service-url Security 2-14 send Getting Started 1-15 server-type Security 2-37 service-type Getting Started 1-15 service-type Security 2-15 service-type System Management 1-17 service-type multicast Multicast 5-1 set authentication password Getting Started 1-17 shell Getting Started 1-18 shutdown Getting
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index ssh server timeout System Management 8-12 ssh user assign rsa-key System Management 8-12 ssh user username authentication-type System Management 8-13 stacking Integrated Management 1-2 stacking enable Integrated Management 1-3 stacking ip-pool Integrated Management 1-3 state Security 2-16 state Security 2-38 stop-accounting-buffer enable Security 2-39 stopbits Getting Started 1-19 stp
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index stp root primary STP 1-15 stp root secondary STP 1-16 stp root-protection STP 1-31 stp tc-protection STP 1-30 stp timer forward-delay STP 1-32 stp timer hello STP 1-33 stp timer max-age STP 1-34 stp transit-limit STP 1-35 super Getting Started 1-20 super password Getting Started 1-20 sysname Getting Started 1-21 sysname System Management 4-3 system-view Getting Started 1-22 t
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index tracert System Management 4-17 traffic-limit QoS/ACL 2-18 traffic-priority QoS/ACL 2-20 traffic-redirect QoS/ACL 2-21 traffic-statistic QoS/ACL 2-22 undelete System Management 1-10 undo snmp-agent System Management 5-17 unknown-multicast drop enable Multicast 3-1 user System Management 1-29 user privilege level Getting Started 1-24 user-interface Getting Started 1-23 user-name-form
Command Manual - Appendix Quidway S3000-EI Series Ethernet Switches Appendix A Command Index Huawei Technologies Proprietary A-19
