Instructions / Assembly

ClarkDietrich Building Systems has prepared this literature with the utmost
diligence and care for accuracy and conformance to standards.
ClarkDietrich intends this information to be accurate, informative, and helpful
as a selection guide for choosing ClarkDietrich Building System products.
However, this information is only to be used for guidance and is not intended
to replace the design, drawings, specifications, and decisions of a professional
architect or engineer.
ClarkDietrich Building Systems or its affiliates shall not be responsible for
incidental or consequential damages, directly or indirectly sustained, nor for
loss caused by application of our products for other than their intended uses.
Our liability is limited to replacement of defective products. Claims shall be
deemed waived unless they are made to us in writing within thirty (30) days
of the date a problem was or reasonably should have been discovered.
ClarkDietrich Building Systems reserves the right to modify or change any
information contained in this literature without notification.
AISI "North American Specification for the Design of Cold-Formed
Steel Structural Members, AISI S-100-2007 with 2010 supplement
ASTM American Society for Testing and Materials
Product specifications
ASTM C645 Non-structural steel framing members
ASTM C955 Load-bearing steel framing
ASTM C847 Plastering steel products
ASTM C841/C1063 Veneer and plaster accessories
ASTM C1047 Beads and trims–metal–paper–vinyl
Material specifications
ASTM A1003 (NS33, ST33L, ST33H, ST50L, ST50H)
ASTM A653 Zinc-coated hot-dip process
ASTM A653/B69 Veneer and plaster accessories
Protective coating standards
ASTM C645 Non-structural steel framing members
ASTM C955 Load-bearing steel framing
ASTM A653 Zinc-coated hot-dip process
ASTM C1063 Veneer and plaster accessories
ASTM C1047 Beads and trims–metal–paper–vinyl
UL
®
Underwriters Laboratories testing standard
UL 263 "Fire Tests of Building Construction and Materials"
Additional code approvals
International Building Code
ClarkDietrich Building Systems
Manufacturing and Sales Locations:
ClarkDietrich Engineering Services.
A full spectrum of solutions.
CALIFORNIA Riverside
P 951.360.3500
F 951.360.3333
CALIFORNIA Sacramento
P 951.360.3500
F 951.360.3333
CONNECTICUT Bristol
P 866.921.0023
F 860.584.6899
FLORIDA Dade City
P 352.518.4400
F 352.518.4450
TEXAS Dallas
P 214.350.1716
F 214.350.7252
CLIP EXPRESS
SM
P 866.638.1908
F 330.372.4055
VINYL CORP.™
P 800.648.4695
F 305.477.4108
cOde aPPrOvals and PerFOrMance standards
ClarkDietrich products meet or exceed these applicable performance standards.
lOcatiOns
USGBC and related logo is a
trademark owned by the U.S.
Green Building Council and is
used by permission.
GEORGIA McDonough
P 678.304.5500
F 678.304.5555
HAWAII Kapolei
P 951.360.3500
F 951.360.3333
ILLINOIS Rochelle
P 800.659.0745
F 513.645.0750
KANSAS Lenexa
P 800.659.0745
F 513.645.0750
MARYLAND Baltimore
P 410.477.4000
F 410.477.1550
OHIO Warren-East
P 330.372.5564
F 330.372.4055
OHIO Warren-West
P 330.372.4014
F 330.372.1945
TEXAS Baytown
P 281.383.1617
F 281.573.1679
LEED
®
Credit MR 2
Construction Waste Management (Up to 2 points)
ClarkDietrich products are manufactured from cold-formed
steel. Steel is 100% recyclable, which helps divert debris
from the waste stream. The contribution to LEED must
be calculated by the contractor based on weight or volume.
LEED Credit MR 4 Recycled Content (Up to 3 points)
ClarkDietrich’s steel products have a minimum of 25.5%
post-consumer recycled content, and 6.8% pre-consumer.
If you wish to report a higher number for your project or seek
Credit MR 5 regional materials, please contact Tech Services
at 888-437-3244 or clarkdietrich.com.
Scan for the most
up-to-date ClarkDietrich
literature.
Toll-Free Phone: [phone]
Toll-Free Fax: [phone]
Technical Services: 888.437.3244
Email: [e-mail]
CENTRAL Crown Point, IN
NORTHEAST Bristol, CT
SOUTHEAST McDonough, GA
SOUTHEAST Roswell, GA
WEST Carlsbad, CA
ClarkDietrich Building Systems is a proud member of
the Steel Framing Industry Association (SFIA). Check
the updated list of Certified Production Facilities at
Architectural Testing's website at www.archtest.com.
The technical content of this literature is eective 5/31/12 and supersedes all previous information.
clarkdietrich.com
Pub. No. CD-Full Line 5/12
109