MSDS

829350 - Quicksilver Quickleen Engine & Fuel System Cleaner
Issue Date: 03-Oct-2017
Page 4
Status: FINAL
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
be completely drained, properly bunged, and promptly shipped to the supplier or a drum reconditioner. All containers should be
disposed of in an environmentally safe manner and in accordance with governmental regulations. Before working on or in tanks
which contain or have contained this material, refer to OSHA regulations, ANSI Z49.1, and other references pertaining to cleaning,
repairing, welding, or other contemplated operations.
SECTION 8: Exposure controls/personal protection
Occupational exposure limits
Chemical Name
ACGIH
OSHA
Mexico
Xylenes (o-, m-, p- isomers)
TWA-8hr: 100 ppm
STEL: 150 ppm
TWA-8hr: 100 ppm
TWA-8hr: 435 mg/m
3
TWA-8hr: 100 ppm (VLE-PPT)
TWA-8hr: 435 mg/m
3
(VLE-PPT)
STEL: 150 ppm (PPT-CT)
STEL: 655 mg/m
3
(PPT-CT)
Carcinogen
Ethylbenzene
TWA-8hr: 20 ppm
TWA-8hr: 100 ppm
TWA-8hr: 435 mg/m
3
Carcinogen
TWA-8hr: 100 ppm (VLE-PPT)
TWA-8hr: 435 mg/m
3
(VLE-PPT)
STEL: 125 ppm (PPT-CT)
STEL: 545 mg/m
3
(PPT-CT)
Note: State, local or other agencies or advisory groups may have established more stringent limits. Consult an industrial
hygienist or similar professional, or your local agencies, for further information. --- = None
Biological occupational exposure limits
Chemical Name
ACGIH
Mexican NOM-047-SSA1-2011
Xylenes (o-, m-, p-
isomers)
Methylhippuric acids in urine: 1.5 g/g creatinine (end of
shift)
Methylhippuric acids in urine: 1.5 g/g creatinine (end of
work shift)
Ethylbenzene
Sum of mandelic acid and phenylglyoxylic acid in urine:
0.15 g/g creatinine (end of shift)
Sum of mandelic acid and phenylglyoxylic acid in urine:
0.7 mg/g creatinine (end of shift at end of work week)
Ethylbenzene in exhaled air: (not critical)
Note: State, local or other agencies or advisory groups may have established more stringent limits. Consult an industrial
hygienist or similar professional, or your local agencies, for further information. --- = None
Engineering controls: If current ventilation practices are not adequate to maintain airborne concentrations below the established
exposure limits, additional engineering controls may be required.
Eye/Face Protection: The use of eye protection that meets or exceeds ANSI Z.87.1 is recommended to protect against potential
eye contact, irritation, or injury. Depending on conditions of use, a face shield may be necessary.
Skin/Hand Protection: The use of gloves impervious to the specific material handled is advised to prevent skin contact. Users
should check with manufacturers to confirm the breakthrough performance of their products. Depending on exposure and use
conditions, additional protection may be necessary to prevent skin contact including use of items such as chemical resistant boots,
aprons, arm covers, hoods, coveralls, or encapsulated suits. Suggested protective materials: Nitrile
Respiratory Protection: Where there is potential for airborne exposure above the exposure limit a NIOSH certified air purifying
respirator equipped with organic vapor cartridges/canisters with R or P95 filters may be used.
A respiratory protection program that meets or is equivalent to OSHA 29 CFR 1910.134 and ANSI Z88.2 should be followed
whenever workplace conditions warrant a respirator's use. Air purifying respirators provide limited protection and cannot be used in
atmospheres that exceed the maximum use concentration (as directed by regulation or the manufacturer's instructions), in oxygen
deficient (less than 19.5 percent oxygen) situations, or under conditions that are immediately dangerous to life and health (IDLH).
Other Protective Equipment: Eye wash and quick-drench shower facilities should be available in the work area. Thoroughly
clean shoes and wash contaminated clothing before reuse.
Suggestions provided in this section for exposure control and specific types of protective equipment are based on readily
available information. Users should consult with the specific manufacturer to confirm the performance of their protective
equipment. Specific situations may require consultation with industrial hygiene, safety, or engineering professionals.
SECTION 9: Physical and chemical properties
Note: Unless otherwise stated, values are determined at 20°C (68°F) and 760 mm Hg (1 atm). Data represent typical values and are not intended
to be specifications.
Appearance: clear Flash Point: 105 °F / 41 °C
Physical Form: Liquid Test Method: Pensky-Martens Closed Cup (PMCC), ASTM D93, EPA 1010