Measurement Guide

Measuring Guide Worksheet
4 Things You Need to Know
Getting Measurements
3500SLX
≤ 3,500 lbs
≤ 1,588 kg
≥ 62.5 in.
≥ 1,588 mm
27 - 50.5 in.
686 - 1,283 mm
≥ 3.5 in.
≥ 89 mm
5000TL
≤ 5,000 lbs
≤ 2,268 kg
≥ 70 in.
≥ 1,778 mm
37 - 60 in.
940 - 1,524 mm
≥ 3.5 in.
≥ 89 mm
7000TL
≤ 7,000 lbs
≤ 3,175 kg
≥ 70.75 in.
≥ 1,797 mm
37 - 60 in.
940 - 1,524 mm
≥ 3.5 in.
≥ 89 mm
6000ELX
≤ 6,000 lbs
≤ 2,722 kg
≥ 86.75 in.
≥ 2,203 mm
53 - 76 in.
1,346 - 1,930 mm
≥ 4 in.
≥ 102 mm
5000TLX
≤ 5,000 lbs
≤ 2,268 kg
≥ 76 in.
≥ 1,930 mm
43 - 66 in.
1,092 - 1,676 mm
≥ 3.5 in.
≥ 89 mm
7000TLX
≤ 7,000 lbs
≤ 3,175 kg
≥ 76 in.
≥ 1,930 mm
43 - 66 in.
1,092 - 1,676 mm
≥ 4 in.
≥ 102 mm
A
Curb Weight
B
Tire Spread
C
Lifting Spread
D
Ground
Clearance
Vehicle #1
_ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __
Vehicle #2
_ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __
Vehicle #3
_ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __
Vehicle #4
_ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ _ _ ____ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __
A - Curb Weight
Weight of a vehicle without passengers or extra load.
B - Tire Spread
Distance between your tire tread.
C - Lifting Point Spread
Maximum point from outside one lifting point to the other
outside lifting point. Same for the minimum.
D - Ground Clearance
It’s important the fully lowered QuickJack has a bit of room
between the rubber block and the lifting point.
A - Locate the Curb Weight
You can nd your vehicle’s curb weight either on the driver’s side
door, in the manual or on the internet.
B - Measure the Tire Spread
Step 1 — Measure the distance between your front and rear tire
treads, keeping the measuring tape 3” above the ground.
Step 2 — Subtract 2” from the measurement in Step 1. The result
is your Tire Spread Measurement (Measurement B).
C - Measure Min. and Max. Lifting Point Spread
Step 1 — Measure the inside of your jacking point to the inside of
the opposite jack point.
Step 2 — Measure the outside of your jacking point to the outside
of the opposite jack point.
These two measurements will become your Lifting Point Spread
(Measurement C).
D - Measure Ground Clearance
Measure the distance between the ground and jacking point. This
is your Ground Clearance (Measurement D).
B D
C
MIN. LIFTING POINT SPREAD
MAX. LIFTING POINT SPREAD
Match vehicle measurements with requirements below
≤ less than or equal to, ≥ greater than or equal to