Instructions / Assembly
Table Of Contents
- QuickJack - Rev. B1 - 5900263 - Sep. 2021 - English
- QuickJack TL Series Manual - English
- Table of Contents
- Introduction
- Shipping
- Safety
- Components
- Accessories
- Specifications
- Frequently Asked Questions
- Setup Checklist
- Setup
- Setup Safety Rules
- Tools
- Selecting a Site
- Unpacking
- Clearances
- Air and Hydraulic Cylinders
- Installing the Hydraulic Elbow Fittings
- About Thread Sealants
- Preparing the Short Hydraulic Hoses
- About Quick-Connect Fittings
- Preparing and Connecting the Long Hydraulic Hoses
- Pressurizing the Air Cylinders
- Find a Location for the Power Unit
- Installing the Hydraulic Fittings on the Power Unit
- Connect the Power Unit to a Power Source
- Filling the Hydraulic Fluid Reservoir on the Power Unit
- Check the Breather Valve
- Bleeding the Hydraulic Cylinders
- Final Checklist Before Operation
- Test the QuickJack
- Leave the Manual with the Owner/Operator
- Operation
- Maintenance
- Troubleshooting
- Wiring Diagrams
- Labels
- Parts Sheets
- Maintenance Log
- Automotive Lift Institute (ALI) Store
- QuickJack - Rev. B1 - 5900263 - Sep. 2021 - French
- QuickJack TL Series Manual - French
- Table des matières
- Introduction
- Expédition
- Sécurité
- Composants
- Accessoires
- Caractéristiques techniques
- Foire aux questions
- Liste de vérification d’installation
- Installation
- Règles de sécurité pour l’installation
- Outils
- Sélectionner un site
- Déballage
- Dégagements
- Vérins pneumatiques et hydrauliques
- Installer les coudes hydrauliques
- À propos des liquides d’étanchéité pour joints filetés
- Préparer les flexibles hydrauliques courts
- À propos des raccords rapides
- Préparer et connecter les flexibles hydrauliques longs
- Mettre les vérins pneumatiques sous pression
- Trouver un emplacement pour le bloc moteur
- Installer les raccords hydrauliques sur le bloc moteur
- Connecter le bloc moteur à une source d’alimentation
- Remplir le réservoir de liquide hydraulique sur le bloc moteur
- Vérifier la soupape de respiration
- Vidanger les vérins hydrauliques
- Liste de vérification finale avant le fonctionnement
- Mettre le QuickJack à l’essai
- Laisser le manuel au propriétaire / à l’opérateur
- Fonctionnement
- Sécurité
- À propos des cales de levage
- Avertissements particuliers concernant le QuickJack
- Positionnement des cales de levage et des cadres
- Levage des cadres QuickJack
- Abaissement des cadres de la première position de verrouillage
- Abaissement des cadres de la position de verrouillage supérieure
- Utilisation du bloc moteur de 12 V c.c.
- Information supplémentaire sur le fonctionnement
- Avertissements concernant le système hydraulique
- Entretien
- Dépannage
- Schémas de câblage
- Schémas de pièces
QuickJack™ Portable Car Jack 14 P/N 5900263 — Rev. B1 — September 2021
Setup Checklist
Following are the steps needed to install a QuickJack. Perform them in the order shown.
☐ 1. Review the setup Safety Rules.
☐ 2. Make sure you have the necessary Tools.
☐ 3. Select the setup Site.
☐ 4. Unpack the Components that came with the QuickJack.
☐ 5. Make sure there is adequate Clearance on all sides and above.
☐ 6. Locate and examine the Air and Hydraulic Cylinders.
☐ 7. Install the Hydraulic Elbow Fittings.
☐ 8. Prepare the Short Hydraulic Hoses.
☐ 9. About Thread Sealants.
☐ 10. Understand Quick-Connect Fittings.
☐ 11. Prepare and connect the Long Hydraulic Hoses.
☐ 12. Pressurize the Air Cylinders.
☐ 13. Find a location for the Power Unit.
☐ 14. Install Hydraulic Fittings on the Power Unit.
☐ 15. Connect the Power Unit to a Power Source.
☐ 16. Fill the Hydraulic Fluid Reservoir.
☐ 17. Check the Breather Valve.
☐ 18. Connect the Hydraulic Hoses.
☐ 19. Bleed the Hydraulic Cylinders.
☐ 20. Review the Final Checklist.
☐ 21. Test the QuickJack.
☐ 22. Leave the Manual for the owner/operator.