Instructions / Assembly
Table Of Contents
- QuickJack - Rev. B1 - 5900263 - Sep. 2021 - English
- QuickJack TL Series Manual - English
- Table of Contents
- Introduction
- Shipping
- Safety
- Components
- Accessories
- Specifications
- Frequently Asked Questions
- Setup Checklist
- Setup
- Setup Safety Rules
- Tools
- Selecting a Site
- Unpacking
- Clearances
- Air and Hydraulic Cylinders
- Installing the Hydraulic Elbow Fittings
- About Thread Sealants
- Preparing the Short Hydraulic Hoses
- About Quick-Connect Fittings
- Preparing and Connecting the Long Hydraulic Hoses
- Pressurizing the Air Cylinders
- Find a Location for the Power Unit
- Installing the Hydraulic Fittings on the Power Unit
- Connect the Power Unit to a Power Source
- Filling the Hydraulic Fluid Reservoir on the Power Unit
- Check the Breather Valve
- Bleeding the Hydraulic Cylinders
- Final Checklist Before Operation
- Test the QuickJack
- Leave the Manual with the Owner/Operator
- Operation
- Maintenance
- Troubleshooting
- Wiring Diagrams
- Labels
- Parts Sheets
- Maintenance Log
- Automotive Lift Institute (ALI) Store
- QuickJack - Rev. B1 - 5900263 - Sep. 2021 - French
- QuickJack TL Series Manual - French
- Table des matières
- Introduction
- Expédition
- Sécurité
- Composants
- Accessoires
- Caractéristiques techniques
- Foire aux questions
- Liste de vérification d’installation
- Installation
- Règles de sécurité pour l’installation
- Outils
- Sélectionner un site
- Déballage
- Dégagements
- Vérins pneumatiques et hydrauliques
- Installer les coudes hydrauliques
- À propos des liquides d’étanchéité pour joints filetés
- Préparer les flexibles hydrauliques courts
- À propos des raccords rapides
- Préparer et connecter les flexibles hydrauliques longs
- Mettre les vérins pneumatiques sous pression
- Trouver un emplacement pour le bloc moteur
- Installer les raccords hydrauliques sur le bloc moteur
- Connecter le bloc moteur à une source d’alimentation
- Remplir le réservoir de liquide hydraulique sur le bloc moteur
- Vérifier la soupape de respiration
- Vidanger les vérins hydrauliques
- Liste de vérification finale avant le fonctionnement
- Mettre le QuickJack à l’essai
- Laisser le manuel au propriétaire / à l’opérateur
- Fonctionnement
- Sécurité
- À propos des cales de levage
- Avertissements particuliers concernant le QuickJack
- Positionnement des cales de levage et des cadres
- Levage des cadres QuickJack
- Abaissement des cadres de la première position de verrouillage
- Abaissement des cadres de la position de verrouillage supérieure
- Utilisation du bloc moteur de 12 V c.c.
- Information supplémentaire sur le fonctionnement
- Avertissements concernant le système hydraulique
- Entretien
- Dépannage
- Schémas de câblage
- Schémas de pièces
QuickJack™ Portable Car Jack 10 P/N 5900263 — Rev. B1 — September 2021
Accessories
Crossbeam Adapter
The Crossbeam Adapter lets you hit the Lifting Points with uneven Frames/Lifting Points.
The Crossbeam Adapter components include: one Crossbeam, two Crossbeam Lift Pads, two
Crossbeam Bases, and two Round Lift Pads and Base Adapters.
Visit the Accessories page of the QuickJack website for more information.
SUV and Light Truck Adapter Kit
The optional SUV and Light Truck Adapter Kit increases the service capability of your QuickJack by
providing stackable Lift Blocks that mount inside the Receiver Trays; for 5000TL/TLX and 7000TL/TLX
models.
The Adapter Kit includes: four low-profile, round Contact Pads, four Bases that accommodate the
Contact Pads and the Extenders, and four 3-inch Extenders that raise the Contact Pads.
Visit the Accessories page of the QuickJack website for more information.
Frame Extension Kit
The Frame Extension Kit is a pair of QuickJack frame extenders that increase the lift-point spread for
5000TL and 7000TL models by 6 inches, for a total lift point spread of 66 inches. They fit snugly
into your QuickJack with no setup required and can be easily taken off and put back on.
Visit the Accessories page of the QuickJack website for more information.
Motorcycle Lift Adapter Kit
The Motorcycle Lift Adapter Kit lets you add a platform on top of your QuickJack Frames, converting it
into a motorcycle lift. This product is not CE certified.
The Adapter Kit includes: a tread plate, heavy-duty tie-down rings, a support axle, a large clamp with
treaded-rubber padding, and an easy-to-use crank for wheel security.
Visit the Accessories page of the QuickJack website for more information.
Ranger RML-1100 Motorcycle Jack
The Ranger RML-1100 Motorcycle Jack is ideal for servicing motorcycles and ATVs up to
1,100 lbs. / 499 kg. It is the perfect accessory for the QuickJack Motorcycle Lift Adapter Kit. This
product is not CE certified.
Visit the Accessories page of the QuickJack website for more information.
JackPak
The portable JackPak lets you add air to the Air Cylinders on each QuickJack Frame. It also includes
additional features for roadside assistance and emergencies.
Refer to jackpak.com for more information.