DP2 L 770 REV 000A VERTICAL WINDLASSES *EN - INSTALLATION AND USER'S MANUAL *Other languages available by scanning the QR code on the back of this manual or on the label on the product.
DP2 L 770 INDEX Index 1 - Information about the product 1.0 - Model code 1.1 - Technical Data 5 5 5 2 - Supply and equipment 2.0 - Standard supply and material included in the package 2.1 - Tools required for installation 2.2 - Recommended Quick® accessories not included 6 6 6 6 3 - Introduction 3.0 - Important notes 3.1 - Precautions 3.2- Precautions for the installer 6 6 7 7 4 - Installation 4.0 - Installation requirements 4.1 - Installation procedures 7 7 8 5 - Wiring diagram 5.
DP2 L 770 1 - Information about the product BEFORE USING THE WINDLASS READ THESE INSTRUCTIONS CAREFULLY. IF IN DOUBT, CONTACT YOUR NEAREST “QUICK®” DEALER. QUICK® RESERVES THE RIGHT TO MODIFY THE TECHNICAL CHARACTERISTICS OF THE EQUIPMENT AND THE CONTENTS OF THIS MANUAL WITHOUT PRIOR NOTICE. IN CASE OF DISCORDANCE OR ERRORS IN TRANSLATION BETWEEN THE TRANSLATED VERSION AND THE ORIGINAL TEXT IN THE ITALIAN LANGUAGE, REFERENCE WILL BE MADE TO THE ITALIAN TEXT. 1.
DP2 L 770 2 - Supply and equipment EN 2.0 - Standard supply and material included in the package • Windlass (top+gearmotor) • Reversing contactor box for DP2 L 770 • Base gasket • Lever • Installation and user’s manual, Warranty • Drilling template 2.1 - Tools required for installation • Drill with bit: Ø 9 mm (23/64”) • Hole saw Ø 58 mm (2” 9/32) and Ø 120 mm (4” 23/32) • Hex wrench: 10 mm and 13 mm 2.2 - Recommended Quick® accessories not included • Controls for control board (mod.
DP2 L 770 3 - Introduction 3.1 - Precautions Quick® windlasses are designed and manufactured to weigh the anchor. • Do not use these products for any other type of operation. • Quick® shall not be held liable for direct or indirect damage caused by improper use of the product. • The windlass is not designed to support loads generated in particular weather conditions (storm). • Operate the product from a position where it is possible to supervise the work area.
DP2 L 770 4 - Installation EN B DECK LEVEL Ensure that the upper and lower surfaces of the deck are as parallel as possible. If this is not the case, compensate the difference appropriately (fig. B). A lack of parallelism could result in a loss of motor power. The deck thickness must be included among the figures listed in the table. In case of different thickness, please contact your Quick® dealer.
DP2 L 770 5 - Wiring diagram 5.0 - Example of connection DP2 L 770 with recommended Quick® accessories for the operation of the windlass QUICK® accessories RADIO POCKET for windlass operation BASIC SYSTEM WINDLASSES CONTROL BOARD WATERTIGHT HAND HELD CHAIN COUNTER WATERTIGHT PANEL CHAIN COUNTER MULTI-PURPOSE WATERTIGHT HAND HELD REMOTE CONTROL REMOTE RADIO CONTROLS RECEIVER MOD. HRC 1002 TRANSMITTERS RADIO POCKET HANDHELD WINDLASSES L2 BLUE BLACK MOTOR BROWN FOOT SWITCHES MOD.
DP2 L 770 6 - Cautions & Use EN 6.0 - Important cautions • Stay clear of chains, ropes and gypsy. • Operate the windlass from a position where it is possible to supervise the work area • Make sure the electric motor is not powered when the windlass is used manually (even when using the handle to disengage the clutch), because people with windlass remote controls (remote push-button panel or radio control) might accidentally operate it. • Secure the chain with a retainer before sailing off.
6 - Cautions & Use DP2 L 770 6.2 - Troubleshooting If the windlass stops and the hydraulic magnetic (or thermal magnetic*) switch has not tripped, wait a few seconds and try again (avoid keeping the button pressed). If the hydraulic magnetic switch, has tripped, reset it and wait a few minutes before weighing anchor once again. If, after a number of attempts, the windlass is still blocked, we suggest to move the boat to release the anchor.
DP2 L 770 9 - List of components DP2 L 770 EN 1 2 3 21 22 21 5 4 23 6 7 8 24 9 25 10 11 12 13 19 14 20 15 16 17 18 N°.
DP2 L 770 228 (8 31/32) 146 (5 3 /4 ) 82 (3 7/32 ) 10 - Dimensions 196 (7 23/32) 108 (4 1/4 ) Quick® reserves the right to introduce changes to the equipment and the contents of this manual without prior notice. In case of discordance or errors in translation between the translated version and the original text in the Italian language, reference will be made to the Italian or English text.
DP2 L 770 REV 000A Product serial number QUICK® S.p.A. - Via Piangipane, 120/A - 48124 Piangipane (RAVENNA) - ITALY Tel. +39.0544.415061 - Fax +39.0544.415047 - www.quickitaly.com - quick@quickitaly.
