User Manual MODEL: HPI 110
Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting The Best From Your HPI110 . . . . . . . . . . . . . . . 4 Flying the HPI110 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 HPI110 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . .
HPI110 User Manual Safety Precautions • Be sure to read the instructions in this section carefully before use. • Make sure you observe the instructions in this manual as the conventions of safety symbols and messages are very important. • We also recommend you keep this instruction manual handy for future reference. Safety Symbol and Message Conventions Safety symbols described below are used in this manual to prevent bodily injury and property damage which could result from mishandling.
HPI110 User Manual WARNING When Installing the Unit When the Unit is in Use • Do not expose the unit to rain or an environment where it may be exposed to water or other liquids, as doing so may result in damage to the bass driver or corrosion of the steel protective grill. • Do not cut, kink, otherwise damage nor modify the speaker cable. Also use speaker cable of at least 1.5mm core diameter.
HPI110 User Manual General Description The HPI 110 is a full frequency range multi-purpose 2-way passive speaker system designed for the live sound touring and permanent installation market. It is suited to full range front-of house sound for mid-throw applications in both stand alone applications or as part of a small array.
HPI110 User Manual Getting The Best From Your HPI110 Connections Suitable Amplification The HPI-110 is an 8 ohm enclosure and can be connected in multiple parallel connections to an amplifier channel that can operate at speaker impedances of 4 ohms. A third speaker box can be connected in parallel if the amplifier can operate into loads of less than 4 ohms. The HPI110 is a mid power level high efficiency system, so ultra high power is not necessary to obtain high sound pressure levels.
HPI110 User Manual Speaker cables Speaker cable needs to be as heavy gauge as conveniently possible for low-loss results. Light gauge cable (below 1.5mm) will create extra resistance and waste amplifier power. This particularly applies to long speaker runs. The amplifier’s damping factor statistic (“punch” for the non technical) is greatly diminished, so keep your speaker cables short and as heavy gauge as practical.
HPI110 User Manual Flying the HPI110 6 The HPI 110 can be flown in a permanent installation by attaching the designed flying hardware. The HPI-110 can be wall mounted or hung in a flown installation using the flying fitting accessory. For more information, see the Quest HPI flying hardware manual. The HPI110 horizontal horn covers both “short-throw” and “long-throw” requirements in a single system.
HPI110 User Manual HPI 110 Wave Guide Examples 30˚ +15˚ -45˚ 7 HPI110 Vertical Front HPI110 Vertical Side HPI Series HPI110 User Manual
HPI110 User Manual HPI110 Specifications Typical Frequency Reponse 110 100 90 80 70 60 8 50 20 50 100 200 500 1k 2k 5k 20k 10k Frequency (Hz) HPI 110 - Frequency Response - 2.83V/1m Technical Specifications User Manual Power Handling 600W RMS Frequency Response 60-18kHz (+/-3dB) Sensitivity 95.
HPI110 User Manual HPI110 Reference Diagram 9 No. Description Spare Part 1 Complete grille (includes glued acoustic foam) HGHPI110 2 Rotating Q-badge (25mm) with Spring Loaded Pin HQB25 3 Asymmetric Horn Flare (GT12) HWG110 4 1.
Register Your Product Thank you for choosing Quest. Please take the time to complete your product registration card which is included with the packaging. Registering your Quest Engineering product will: • CONFIRM YOUR WARRANTY • REGISTER YOUR PRODUCT • PROTECT YOUR NEW PRODUCT REGISTER ONLINE: www.questaudio.net/registration www.questaudio.
