Ness Ultimate Series 10x Mini Rugged Speed Dome Installation Manual Installation Manual revision 2.
Installation Guide Preface The information given in this manual was current when published. The company reserves the right to revise and improve its products. All specifications are subject to change without notice. Notice This manual provides the installation information for indoor and outdoor Vandal Proof Mini Speed Domes.
Installation Guide This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with Directive 2002/96/EC. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By proper waste handling of this product you ensure that it has no negative consequences for the environment and human health, which could otherwise be caused if this product is thrown into the garbage bin.
Installation Guide Warnings and Cautions • Handle the camera carefully Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handing or storage. • Installing electricity wiring carefully Ask qualified personnel of electrical wiring for the installation. Please note that input electricity to the unit is at tolerance of DC12V/AC24V ± 10%.
Installation Guide • Do not use strong or abrasive detergents when cleaning the camera body Use a dry cloth to clean the camera when dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently. • Never face the camera towards the sun Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, the camera may be smeared or damaged.
Installation Guide Table of Contents 1. 2. 3. Introduction.................................................................................................................7 Standard Package Content ........................................................................................9 Dome Setups and Cable Connection ...................................................................... 11 3.1 Preparations for Indoor Dome Camera Setups.................................................. 11 3.
Installation Guide 6. System Integration ...................................................................................................53 6.1 Using Pelco Keyboard .......................................................................................53 6.2 Using Philips Allegiant Keyboard .......................................................................54 Appendix A: Technical Specification .............................................................................
Installation Guide 1. Introduction The Vandal Proof Mini Speed Dome Camera is a new subcompact high speed dome camera designed to deliver superb performance and durability with an intelligent and stylish housing that is suitable in any security and surveillance installation. With weather resistant housing (IP66 standard) and optional sunshield, the outdoor dome camera can face harsh circumstances.
Installation Guide Connect dome cameras to other devices, as shown in the diagram, to complete a video surveillance system. NOTE: To extend the network distance up to 1.2 km (4000 feet) and to protect the connected devices, it is highly recommended to place a repeater at the mid-point. However, a repeater may be needed in the network distance less than 1.2 km if the used cables are not the CAT 5, 24-gauge cables (see 3.4.4 RS-485 Connector). Refer to the repeater’s manual for detailed information.
Installation Guide 2. Standard Package Content Before proceeding, please check the box contains the items listed here. If any item is missing, or if damage is evident, DO NOT install or operate the product and contact your dealer for assistance. Indoor Vandal Proof Mini Speed Dome Hard Ceiling Mount and Decoration Ring 12V DC Power Adaptor Power Cord (12V DC Only) Dome Body with 4.
Installation Guide Outdoor Vandal Proof Mini Speed Dome Data Cable for Power Dome Body 5.
Installation Guide 3. Dome Setups and Cable Connection Before installing or connecting the dome camera, please refer to this section and complete preparation, switch setting and communication switch settings. 3.1 Preparations for Indoor Dome Camera Setups Follow the steps below to remove the PE cushion inside the dome cover and take off the lens cap to prepare for subsequent switch setting. Step 1: Unpack the dome package and take out the dome body.
Installation Guide 3.2 Preparations for Outdoor Dome Setups This installation procedure is for the outdoor dome equipped with sunshield housing. Please follow the steps below to complete dome housing installation. STEP 1 Unpack the dome package and take out the dome body. STEP 2 Rotate the top holder and take it off from the dome body. STEP 3 Remove the protective cover and PE sheet. STEP 4 Attach the dome cover to the dome body.
Installation Guide Note that the tiny protrusion on the dome cover must align with one of the four holes on the dome body. STEP 5 Gently pressure the dome cover downward with two hands on the side of it. DO NOT press the cover, as shown in the figure; this might cause damage to the dome body. STEP 6 Screw the dome cover and body together. STEP 7 Set the switches located on the bottom of the dome body. Refer to section 3.3 Dome Setups for detailed information setting. 3.
Installation Guide 3.3.1 Switch Definition Please refer to the following figures and table for switch location and definitions. Indoor Dome A B C D E F G 3.3.2 Outdoor Dome Reserved Communication Switch Dome ID Switch Dome Control Protocol Switch RJ-45 Connector (for IP Dome only) 22-Pin Connector ISP Connector (for FW upgrade) Communication Switch Setting The table below shows the function of each pin within the Communication Switch.
Installation Guide RS-485 Setting Half-duplex 3.3.3 Full-duplex Dome ID Setting Please change the dome ID if there is more than one dome on the same installation site. Before installing the dome camera, use the switch to change your speed dome ID by turning the arrow to the desired number respectively. For instance, if the dome ID is 123, the ID switch should be set as shown below. NOTE: No two domes should be given the same ID, or communication conflict may occur.
Installation Guide Switch No. Protocol Baud Rate 00 VCL 9600 01 Pelco D 2400 02 Pelco P 4800 04 Chiper 9600 05 Philips 9600 07 DSCP 9600 08 AD422 4800 09 DM P 9600 11 Pelco D 4800 12 Pelco D 9600 13 Pelco P 2400 14 Pelco P 9600 15 JVC 9600 Select protocol: Pelco D, with switch no. 01 and baud rate 2400, for instance, the protocol switch should be set as below.
Installation Guide • RS-485 cable carries commands from a control device to the dome cameras. A CAT 5, 24 gauge cable is recommended. • The power cable provides either AC 24V or DC 12V power supply to the dome. NOTE: Ensure power supply corresponds with the dome’s power requirement, or product impairment will occur. If any mistake happens, please contact with a qualified maintenance engineer. 3.4.
Installation Guide 3.4.3 22-Pin Connector Definition With the 22-pin connector, installers can simply connect the power, video and RS-485 cables to the dome at once. Particularly, the alarm pins are serviceable for connecting alarm input and output devices, such as alarm sensors, sirens or flashing lights with the surveillance system. For the definition of each pin, please refer to the list below. The 22-pin connector definition is listed as below.
Installation Guide 3.4.4 RS-485 Connector RS-485 is the interface that communicates the dome camera and its control device. Please connect the control keyboard to the speed dome through the terminal block. The recommended cables for RS-485 communication are CAT 5 cables; maximum cable length for over 24-gauge wire is 4000 feet (1219 meters). If the total cable length exceeds 4000 feet, using a repeater to maintain the signals is recommended.
Installation Guide Insert the terminal into the pin holes on the connector housing, with the hook outward, as indicated in the figure. To unlock the terminal, press the hook, as indicated in the figure, with a proper tool and pull it out gently. Connect the 22-pin connector to the dome camera.
Installation Guide 4. Dome Installation Basing on user’s installation environments, the dome can be installed on ceiling, on wall or on pole. In the following sections, various indoor dome installation accessories, installation methods and installation procedures will be described in detail. In addition, the next section will provide both indoor and outdoor domes’ dimensions for your reference before installation. 4.1 Dome Dimensions The indoor dome dimension is Ø133 x 173 mm (5.2 x 6.8 Inches).
Installation Guide 4.2 Optional Accessories Indoor Dome Camera Accessories Vandal Proof Cover Diameter: 137 mm (5.4 inches) Security Screw Set (equipped with Vandal Proof Cover) Indoor Mount Kit For mounting the indoor dome camera onto a gooseneck/straight tube. White; Diameter: 140 mm (5.5 inches); Height: 74 mm (2.9 inches); 0.3 kg (0.
Installation Guide Outdoor Dome Camera Accessories Vandal Proof/Transparent/Smoke Cover Diameter: 137 mm (5.4 inches) Security Screw Set (equipped with Vandal Proof Cover) Power Adapter 77H07-A1030 (Input: 100~115VAC/Output: 24VAC 72VA) 77H07-A2030 (Input: 220~230VAC/Output: 24VAC 72VA) NOTE: When wiring, make sure the G/Y wire (Ground) inserted into the mid-pin of the terminal block Sunshield (Outdoor Dome) White Color, Height: 89.9 mm (3.54 inches); Diameter: 190 mm (7.48 inches); 0.15 kg (0.
Installation Guide T-Bar Ceiling Mount, T-Bar Body Holder and Red Sticker For in-ceiling Installation use. T-Bar Ceiling Mount: Height: 85 mm (3.35 inches); Diameter: 180 mm (7.1 inches); 0.5 kg (1.1 lbs).Red Sticker: 155 +/- 3 mm (6.1 +/- 1.2 inches) Ceiling Panel For ceiling mounting. Zn platted; 610×305 mm (24×12 inches); Diameter: 155 mm (6.1 inches) Gooseneck Tube White Color; Iron, 298×385 mm (11.73×15.56 inches) ; 2.1 kg (4.
Installation Guide Mini Pendant Mount White; 184×104×115.2 mm (7.24×4.09×4.54 inches); 0.6 kg (1.2 lbs). Supplied with rubber washer-8×1, pendant tube washer×1, spring washer-8×1 and M8*12 screw×1. Straight Tube White, Iron, Height: 250/500 mm (9.8/19.7 inches) ,Diameter: 50 mm (2 inches) 1 kg (2.2 lbs) / 1.8 kg (4 lbs), Supplied with rubber washer-8×1, pendant tube washer×1, spring washer-8×1 and waterproof rubber×1, M8*12 screw×1. Corner Plate Mini For mounting with Mini Pendent Mount.
Installation Guide Corner Standard Mounting Plate White, 222×204×117 mm (8.7×8×4.6 inches); 2 kg (4.4 lbs); Supplied with washer-8×4, spring washer×4, M8*16 screw×4, M8 nut×4. Corner Thin Box White/Ivory, 300×164×222 mm (11.8×6.5×8.7 inches); 3 kg (6.7 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4. Corner Wide Box White/Ivory; 232×234×210 mm (9.1×9.2×8.3 inches); 2.7 kg (6 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4.
Installation Guide Pole Thin Box White/Ivory; 291×136×242 mm (11.5×5.4×9.5 inches); 3.1 kg (6.9 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4. Pole Wide Box White/Ivory, 270×166×155 mm (10.6×6.5×6.1 inches); 3.2 kg (7.1 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4. Wall Box Mounting Ivory, 270(L)×166(W)×95(D) (10.6×6.5×3.7 inches); 2.2 kg (4.
Installation Guide Pole Thin Direct Mounting White/Ivory, 232×136×60 mm (9.1×5.4×2.4 inches); Diameter: 112~140 mm (4.4~5.5 inches); 0.7 kg (1.6 lbs); Supplied with stainless steel straps×4, M8*16 screw×4, washer×4. Pole Wide Direct Mounting White/Ivory, 270×170×60 mm (10.6×6.7×2.4 inches); Diameter: 112~130 mm (4.4~5 inches); 1 kg (2.2 lbs); Supplied with stainless steel straps×4, M8*16 screw×4, washer×4. Stainless Steel Straps For fixing Pole Direct Mounting/ Pole Box on the pole. Length: 700 mm (27.
Installation Guide Other Application Accessories Repeater/Converter D77R1: RS-485/RS-422 Repeater D77R2: RS-232 between RS-485/RS-422 D77R3: Bi-phase to RS-485/RS-422 D77R1 D77R2 D77R3 Connector Box (Indoor Application) Recommended for wiring indoor dome alarm cables. White Color. 92×42 mm (3.7×1.7 inches); 0.13 kg (0.3 lbs); Supplied with cable×1, bracket×1 and M3*6 screw×2. Power Box White, 186.5×147 mm (7.3×5.8 inches); 2.6 kg (5.
Installation Guide 4.3 Ceiling Mount Generally, there are three kinds of dome camera ceiling mounting methods: hard-ceiling, in-ceiling and mounting with straight tube. Refer to the following sections for more details. The following figures show how cables connect to the dome camera in different ways. 4.3.
Installation Guide STEP 1 Screw the Fixing Plate to your dome body. STEP 2 Remove the Hard Ceiling Mount from the Decoration Cover. STEP 3 Attach the Mount to the ceiling. Mark the locations where all three ceiling holes should go. STEP 4 Drill these holes on the hard ceiling. STEP 5 Fix the screws. Mount with three STEP 6 Connect the data cable through the center hole of the Mount to the dome body. NOTE: If use an IP dome, a network cable is needed other than the data cable.
Installation Guide STEP 7 Attach the dome body to the Mount and rotate the dome body clockwise. Tighten the fixing screw on the fixing plate. STEP 8 Assemble the Decoration Ring to the Mount. Completion 4.3.2 In-Ceiling Mounting (Indoor) Here lists the items and tools needed to mount the dome camera into the ceilings. The supplied items are all in the dome camera package.
Installation Guide Tools Needed: • Tool for cutting a circle on the ceiling • (+,–) Screw Driver Follow the steps to install the integrated high speed dome camera with T-Bar Ceiling mount accessory for in-ceiling mounting. STEP 1 Screw the T-Bar Body Holder, which is equipped with the T-Bar, onto the dome back, as shown in the figures. STEP 2 Place the Red Sticker on the ceiling plate, and cut the circle part out of the ceiling. STEP 3 Put up the T-Bar into the ceiling hole.
Installation Guide STEP 4 Rotate the T-Bar’s wings to fix the T-Bar at the edge of the ceiling opening. STEP 5 Tighten the screws on the wings. STEP 6 Connect the data cable to the dome body through the center hole of the bracket. NOTE: If use an IP dome, a network cable is needed other than the data cable. STEP 7 Mount the dome body onto the bracket and rotate it clockwise. Then ensure the dome body fastened firmly and screw the T-Bar Body Holder.
Installation Guide STEP 8 Assemble the Decoration Ring to the T-Bar. Completion 4.3.3 In-ceiling Mounting with Ceiling Panel To mount the dome camera to a suspended ceiling with the T-Bar, the ceiling panel could be employed, as shown in the figure below. Follow the steps below for installing the ceiling panel. Step 1: Cut the ceiling half. Step 2: Put the ceiling panel upward to the ceiling opening. Step 3: Attach and fasten the T-Bar mount onto the panel (Refer to the previous section 4.2.
Installation Guide 4.3.4 Ceiling Mounting with Straight Tube The straight tube is available in different length: 25 cm and 30 cm. Items Needed: • Dome Camera • Straight Tube and other equipped items (optional accessory) • Waterproof Rubber (standard accessory for the outdoor dome) • Screws and Screw Anchors for fixing the straight tube onto the ceiling (not supplied) Tools Needed: • Tool for drilling • Tool for screwing Follow the steps to mount the dome with the straight tube.
Installation Guide Ceiling Mount: Straight Tube + Waterproof Rubber 4.4 Wall Mount 4.4.1 Wall Mounting with Gooseneck Tube The following figures show how cables run through the tube in different ways.
Installation Guide Tools Needed: • Tool for drilling • Tool for screwing Follow the steps to mount the dome with the gooseneck tube. 1) Make a cable entry hole on the wall to recess the cables. Otherwise, cables can be threaded through the cable entry hole on the tube. 2) Fix the Gooseneck Tube on the wall with proper screws and screw anchors (not supplied). 3) Attach the waterproof rubber to the gooseneck tube. 4) Thread the cables through the gooseneck tube and the top holder.
Installation Guide 4.4.2 Mini Pendant Mount Items Needed: • Dome Camera • Mini Pendant Mount and other equipped items (optional accessory) • Waterproof Rubber (standard accessory for the outdoor dome) • Screws and Screw Anchors for fixing the Mini Pendant Mount (not supplied) Tools Needed: • Tool for drilling • Tool for screwing Follow the steps to mount the dome with the Mini Pendant Mount. 1) Make a cable entry hole on the wall to recess the cables.
Installation Guide Mount with the supplied screws and washers. 6) Connect the cables to the dome camera. Then attach the dome to the top holder and fix them with the supplied screw. 4.4.
Installation Guide washers. Then adjust the waterproof rubber to the junction of straight tube and top holder. 6) Connect the cables to the dome camera. Then attach the dome to the top holder and fix them with the supplied screw. Wall Box Mounting: Wall Box Mount + Gooseneck Tube + Waterproof Rubber 4.5 Corner Mount 4.5.1 Corner Standard/Mini Mounting Plate With the corner standard/mini mounting plate and gooseneck tube/mini pendant mount, the dome can be mounted on corner wall.
Installation Guide standard/mini mounting plate and gooseneck tube/mini pendant mount. 1) Make a cable entry hole on the wall to recess the cables. Otherwise, cables can be threaded through the cable entry hole on the tube. 2) Fix the Corner Standard/Mini Mounting Plate on corner wall with proper screws and screw anchors (not supplied). 3) Attach the gooseneck tube/mini pendant mount to the fixed mounting plate with the supplied screws and washers.
Installation Guide Items Needed: • Dome Camera • Gooseneck Tube and other equipped items (optional accessory) • Corner Thin/Wide Box (optional accessory) • Waterproof Rubber (standard accessory for the outdoor dome) • Screws and Screw Anchors for fixing the Corner Thin/Wide Box (not supplied) Tools Needed: • Tool for drilling • Tool for screwing Follow the steps to mount the dome with the corner box and gooseneck tube. 1) Make a cable entry hole on the wall to recess the cables.
Installation Guide Corner Box Mounting: Corner Thin/Wide Box + Gooseneck Tube + Waterproof Rubber 4.6 Pole Mount 4.6.1 Pole Thin/Wide Direct Mounting The dome can be installed on a pole with a thin/wide direct mounting accessory and a gooseneck.
Installation Guide screws and washers. 3) Attach the waterproof rubber to the gooseneck tube. 4) Thread the cables through the gooseneck tube and the top holder. NOTE : After threading the cables, please block the cable entry hole with the supplied sponge(s) to avoid insects entering the tube. 5) Fix the top holder to the gooseneck tube with the supplied screws and washers. Then adjust the waterproof rubber to the junction of straight tube and top holder. 6) Connect the cables to the dome camera.
Installation Guide 2) Fix the gooseneck tube on the pole box with the supplied screws and washers. 3) Attach the waterproof rubber to the gooseneck tube. 4) Thread the cables through the gooseneck tube and the top holder. NOTE : After threading the cables, please block the cable entry hole with the supplied sponge(s) to avoid insects entering the tube. 5) Fix the top holder to the gooseneck tube with the supplied screws and washers.
Installation Guide 5. System Expansion 5.1 Connecting with Connector Box (Indoor) Ideally being used in indoor installation circumstances, a Connector Box provides easy wiring and well organized connection between alarms, cameras and other devices, for easy installation. To connect the connector box with other devices: • Use a RS-485 cable (CAT 5 is recommended) to complete RS-485 communication wiring with control devices such as DVRs and Control Keyboards.
Installation Guide 5.2 Connecting with Power Box (Outdoor) A power box contains a 24V AC adapter, two terminal blocks (for communication and power) and one alarm board. With an IP66 case, the Power Box is ideal for outdoor installation environment. Two models are available: 100~115V AC power input (P1030) and 220~230V AC (P2030).
Installation Guide 5.3 Data Formats Transforming To integrate other surveillance devices with the high speed dome cameras, we provide three kinds of converter/repeater to transform the communication formats between devices. If a converter/repeater is used, the total network distance of the surveillance system can be extended, and the connected devices will also be protected. Up to 10 devices are allowed to connect to each repeater.
Installation Guide Outdoor Dome Application 50
Installation Guide 5.4 Signal Distribution Unit The RS-485 Signal Distribution Unit (SDU) is designed to relay control codes to speed dome cameras. It is capable of communicating with cameras up to 1.0 kilometers away. Additionally, the SDU can be installed in either “star” or “daisy chain” configuration with up to 160 cameras (see the diagrams below). Its versatile installation configuration makes an easy integration into expanding surveillance systems.
Installation Guide 5.5 Coaxial Telemetry The Coaxial Telemetry is a low-cost solution to long distance connection between dome cameras and controlling devices (e.g. DVR and keyboard). It simplifies the work of wiring by transmitting video and RS-485 control signals via one BNC line, so that to bring users economical benefits. The following is the coaxial telemetry application diagram. For more information, please refer to the coaxial telemetry’s quick installation guide.
Installation Guide 6. System Integration The dome camera is allowed to be integrated into other suppliers' surveillance systems with large set of built-in protocols. Refer to the following sections for more information. 6.1 Using Pelco Keyboard The speed dome camera can be controlled through a Pelco keyboard which built in with D protocol and P protocol. Please follow the instruction to manipulate our speed dome by a keyboard with D and P protocols.
Installation Guide Cable Definition (D Protocol Keyboard to PTZ Camera) Tx - 6 Tx+ 5 GND 4 1 Tx+ 2 3 GND GND 3 Rx- 2 Rx+ 1 4 Rx+ 5 Rx6 Tx- For D Protoc ol Keyb oa rd 6.2 For Sp e ed Dom e Using Philips Allegiant Keyboard The dome cameras can be integrated into Philips Allegiant systems through D77R3 repeaters. Please follow the instructions to control dome cameras through Philips Allegiant systems. Symbol Definition Command dome cameras to go to a specific preset position.
Installation Guide Appendix A: Technical Specification Items DH500 DH600 CAMERA CCD Sensor 1/4" EXview CCD Optical Zoom 12x 12x Digital Zoom 1×~ 10× variable NTSC 380k PAL 440k Effective Pixels Horizontal Resolution 470 TVL Scanning System NTSC / PAL Synchronization Internal / Line Lock 1.
Installation Guide Dimension ∅133 x 173 mm (5.2 x 6.8 Inches) ∅172 x 260 mm (6.8 x 10.2 Inches); ∅190 x 260 mm (7.5 x 10.2 Inches) w/ sunshield 1.2 kg (2.6 lbs) 2.1 kg (4.6 lbs) DC12V/AC24V ± 10% AC24V ± 10% 14 W 52 W (with Heater) Weight Power Source Power Consumption Regulatory All Specifications are subject to change without notice.
www.ness.com.au Head Office: Ness Security Products Pty Ltd ABN 28 069 984 372 Ph +61 2 8825 9222 Fax +61 2 9674 2520 ness@ness.com.au NSW Ph 02 8825 9222 Fax 02 9674 2520 sales@ness.com.au VIC Ph 03 9875 6400 Fax 03 9875 6422 nessmelb@ness.com.au QLD Ph 07 3399 4910 Fax 07 3217 9711 nessbris@ness.com.au WA Ph 08 9328 2511 Fax 08 9227 7073 nessper@ness.com.au SA Ph 08 8152 0000 Fax 08 8152 0100 adelaide@ness.com.au Copyright Notice All rights reserved.
