T-229LA-L User manual (Rev.1.0) Sinocastel Co., Ltd.
1. Product description The T-229LA-L terminal can provide passenger car and commercial vehicle customers with a variety of Telematics services including location, security, diagnosis, driving behavior analysis, on-board access points, etc., and can provide data accumulation for vehicle manufacturers and related supporting enterprises. At the same time, it can also meet the requirements of government departments for monitoring and remote emission monitoring of new energy vehicles.
The vehicle-mounted OBD system can communicate with external devices that follow the same communication protocol through this interface. Micro USB interface Connect to the computer via USB cable. SIM card holder This interface is used to install the SIM card. 2.2 Status indication Indication colour Working status type Flashing (on for 0.5s, off for 0.
Indicator light Antenna Environment al parameters 3. FDD LTE B2/B4/B12 WCDMA B2/B4/B5 Network communication protocol: embedded TCP/IP protocol stack GPS/LTE/OBD indication 4G antenna Built-in GPS antenna Built-in or external Operating temperature storage temperature humidity -30℃ ~ +70℃ -40℃ ~ +85℃ 5%～95% (no frost) Setting parameters 3.1 PC Tool parameter setting Download the USB driver and PC Tool from http://www.sinocastel.com/Support/ and install it.
4.3 Install terminal 1. Before installing the terminal, make sure that the network parameters, working mode and other parameters are configured correctly; 2. When the vehicle is turned off, align the terminal with the OBD interface of the vehicle through the cable and insert it in place; 3. For vehicles that will affect the cover after the connector is inserted, please use an OBD extension cable and fix the terminal in a suitable position; 4.
*The terminal enters the dormant state after the flame is turned off, but the battery power is still consumed. The terminal dormant current is 5mA. In order to avoid battery loss, it is recommended to unplug the terminal before parking the vehicle for a long time (such as more than 5 days). Vehicle test platform 5. Product features 5.1 Communication protocol This product supports all OBD II standard protocols and is compatible with SAE J1939 protocol.
encryption. Every time the device logs in to the server, it will synchronize the AES key with the server. By default, encryption is disabled. 5.3 GPS report timing upload The terminal collects GPS data and uploads it according to the set collection time interval and the number of upload packages. The time interval is 2-600s, and the default setting is 30s. 5.4 Statistics of mileage In each report information, mileage statistics are included. 5.
(3) Low battery voltage: 10.5 V (4) The coolant temperature is too high: 98℃ (5) Rapid acceleration: 0.4 g (6) Sudden braking: 0.6 g (7) Rapid lane change: 0.4g (8) Sharp turn: 0.5 g (9) Vibration: 1.5 g (10) Vibration: 0.08 g (11) Excessive engine idle time: 15 minutes (12) Fatigue driving: 240 minutes 5.8 Working mode The terminal supports three working modes, namely: passenger car, commercial vehicle and tracker.
The content of this manual is based on the "current situation". Shenzhen Aerospace Wireless Communication Technology Co., Ltd. does not provide any guarantee for the correctness, reliability or content of this manual. Shenzhen Aerospace Wireless Communication Technology Co., Ltd. reserves the right to revise or retract this manual at any time without notice. 7.
Maintenance records Product number: Failure and maintenance records date Fault description Maintenance records Repair man user Note: The warranty unit must fill in this form carefully during warranty 8. statement Without the written permission of Shenzhen Aerospace Wireless Communication Technology Co., Ltd., it is prohibited to copy, transmit, distribute or save part or all of this file in any form. Shenzhen Aerospace Wireless Communication Technology Co., Ltd.
and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
