Installation Guide

ManualsBrandsQuectel ManualsElectronicsLTE Module

Installation Guide for

VeeaHub™ Pro Outdoor

Version 0.3

Veea, Inc. Confidential & Proprietary

Introduction

The VeeaHub Pro Outdoor (VHH10) is a ruggedized version of the popular VeeaHub Pro intelligent

wireless hub. The VHH10 has an IP-65 rating and is designed to be installed in outdoor environments.

This document will be your guide to the proper installation of the VHH10.

VHH10 Installation Kit

The VHH10 installation kit is packed in a separate box from the VHH10 unit itself. The installation kit

contains:

• 1 x Wall Mounting Bracket (2 pieces)

• M8 screws to attach mounting bracket to VHH10

• M8 screw to attach grounding cable

• 2 x M12 male connectors with pigtail cables for ethernet

• 1 x M12 female connector with pigtail cable for power

• 1 x Self-locking tweezers (for SD card insertion)

Understanding the VHH10

As you read through this document, please refer to the following diagrams to help you locate the various

connections, buttons and Indicators:

1 2 3 4 5 6 7

Figure 1

1. Lower LED

2. Upper LED

3. Power Connector (M12 male)

4. Ethernet Connector (M12 female) – this connection supports PoE

5. Ethernet Connector (M12 female)

Summary of content (8 pages)

PAGE 1
Installation Guide for VeeaHub™ Pro Outdoor Version 0.3 Introduction The VeeaHub Pro Outdoor (VHH10) is a ruggedized version of the popular VeeaHub Pro intelligent wireless hub. The VHH10 has an IP-65 rating and is designed to be installed in outdoor environments. This document will be your guide to the proper installation of the VHH10. VHH10 Installation Kit The VHH10 installation kit is packed in a separate box from the VHH10 unit itself.
PAGE 2
6. RS232/422/485 (M12 female) – for serial IoT connection 7. Reset button A B C Figure 2 A. LTE Primary Antenna B. Bluetooth Antenna C. LTE Diversity Antenna Understanding the Lights The lights (refer to Figure 1) are named as follows: 1. Lower – This light is the lower of the pair of lights on the side of the unit. 2. Upper – This light is the upper of the pair of lights on the side of the unit. Each of these lights are either off, on or flashing read, green or blue.
PAGE 3
ethernet connection. Use the connectors provided in the installation kit to install the ethernet connection(s), as needed. Refer to Table 3 for the pinout information and cabling recommendations for each connection attaching to the lower edge of the VHH10 unit.
PAGE 4
For reference, Table 4 shows the pin assignments for the far end of the cables coming from the VHH10 unit.
PAGE 5
Figure 3 Grounding Connection The VHH10 unit must be properly grounded to ensure reliable operation. The grounding connection (see Fig 4) must be securely and effectively connected to an actual earth ground. A grounding stake, grounded pole or similar grounded metal structure may be used. Figure 4, shows the back of the VHH10 unit with the unit piece of the wall mounting bracket attached. The location of the grounding connection is shown in that Figure by the large green arrow.
PAGE 6
Figure 4 Wall Mounting Procedure 1. Attach the unit piece of the wall mounting bracket to the back of the VHH10 unit with three M8 bolts, as shown in Figure 4. Please notice that a single bolt attaches in the middle at the top of the bracket and two bolts attach the bottom of the bracket. The holes in the top corner of the bracket are unused. 2. Attach the wall piece of the wall mounting bracket to the wall surface so that it is oriented as shown in Figure 5.
PAGE 7
5. Insert 2 M8 screws into the locking flanges at the bottom to fasten the two pieces of the mounting bracket together (see Figure 3). Figure 5 Power Connections If Using PoE to Power the Unit A PoE switch or a cable injector may be used to power this unit. Refer to Tables 3 & 4 for connection information. If Using a Separate DC Power Cable Refer to Table 3 for power cable connections. When using a separate DC power cable, a minimum 14# conductor cable should be used. Maximum length is 50 feet.
PAGE 8
The SIM card normally comes pre-installed in the unit if it was manufactured with the LTE option. The SIM card port is sealed with a weatherproof seal. Do NOT unnecessarily open this port to avoid impairing the weather resistance. If it becomes necessary to open the port, take care to ensure that the port sealing ring and closure cap remains clean and undamaged and that the cap is closed securely. Reset Button Use The reset button is located on the bottom surface of the unit (see Fig x).