User Guide
Table Of Contents
- 1. Scope
- 2. LMU-3040 Hardware Specifications
- 3. LMU-3040™ Connectors
- 4. Getting Started
- 4.2 SSH Credentials
- 4.3 Interactive “AT Console”
- 4.4 Command Line Interface (CLI)
- 4.5 Log File
- 4.6 Backup Logs
- 4.7 File Components
- 4.8 Software & Script Updates
- 5. PEG2
- 5.2 PEG2 File
- 5.3 PEG2 TAG Definitions
- 5.4 Multiple Modifiers
- 5.5 PEG1 -> PEG2 Conversion
- 5.6 PEG2 Native Editor
- 6. LMU32 vs EdgeCore Platform Differences
- 6.1 I/O Mapping & Wake-Up Sources
- 6.2 LMU Firmware Updates (Delta Files)
- 6.3 Vehicle Bus PID Polling Rate
- 6.4 PEG2 “Lines”
- 6.5 Event Index Field
- 6.6 Remote Debug PEG Action
- 6.7 Modem/GPS Reset
- 6.8 SIM Form Factor
- 6.9 Boot Reason
- 6.10 Peg Resources
- 6.11 GPS
- 6.12 Motion Logs (4hz vs 5hz GPS Sample Rate)
- 6.13 Time Sync Precedence
- 6.14 Version String in ID Reports
- 6.15 Firmware Revision Convention
- 6.16 Status LEDs
- 6.17 Dual APN Mode
- 6.18 Version Reports (App Message 111)
- 7. Installation Verification
- 8. Regulatory Information
COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Page
Reproduction use or disclosure to third parties without express permission is strictly prohibited. ©2021 CalAmp 38 of 40
LMU-3x40 Training Guide
Revision & Date
1.6 – 03/24/2021
8. Regulatory Information
Human Exposure Compliance Statement Pursuant to 47 CFR § 24.52 of the FCC Rules and Regulations, personal
communications services (PCS) equipment is subject to the radio frequency radiation exposure requirements specified in §
1.1307(b), § 2.1091 and § 2.1093, as appropriate.
CalAmp Wireless Networks Inc. certifies that it has determined that the LMU3x40 ™ complies with the RF hazard
requirements applicable to broadband PCS equipment operating under the authority of 47 CFR Part 24, Subpart E of the
FCC Rules and Regulations. This determination is dependent upon installation, operation and use of the equipment in
accordance with all instructions provided.
The LMU3x40 ™ is designed for and intended to be used in fixed and mobile applications. “Fixed” means that the device is
physically secured at one location and is not able to be easily moved to another location. “Mobile” means that the device
is designed to be used in other than fixed locations and generally in such a way that a separation distance of at least 20 cm
is normally maintained between the transmitter’s antenna and the body of the user or nearby persons. The LMU3x40 ™ is
not designed for or intended to be used in mobile applications (within 20 cm of the body of the user) and such uses are
strictly prohibited.
To ensure that the LMU3x40 ™ complies with current FCC regulations limiting both maximum RF output power and human
exposure to radio frequency radiation, a separation distance of at least 20 cm must be maintained between the unit’s
antenna and the body of the user and any nearby persons at all times and in all applications and uses. Additionally, in
mobile applications, maximum antenna gain must not exceed 3.2 dBi.
FCC Rules and Industry Canada (IC) regulatory information Compliance Statement (Part 15.19)
The equipment device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received including
interference that may cause undesired operation. Warning (Part 15.21)
Changes or modifications not expressly approved by TransCore Amtech Systems could void the user’s authority to operate
the equipment. Manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment.
Compliance Statement (Part 15.105(b))