GV600 User Manual GV600MA User Manual GPS Tracker QSZTRACGV600UM0101 Version: 1.
GV600MA User Manual Document Title GV600MA User Manual Version 1.01 Date Dec , 2018 Status Released Document Control ID QSZTRACGV600UM0101 General Notes Queclink offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Queclink. The information provided is based upon requirements specifically provided to Queclink by the customers.
GV600MA User Manual Contents 0. Revision History ............................................................................................................................. 2 1. Introduction .................................................................................................................................. 3 1.1. Reference............................................................................................................................. 3 1.2. Terms and Abbreviations ..............
GV600MA User Manual Table Index Table 1. GV600MA Protocol Reference ............................................................................................. 3 Table 2. Terms and Abbreviations ..................................................................................................... 3 Table 3. Product Model ..................................................................................................................... 4 Table 4. Parts List ...............................................
GV600MA User Manual Figure Index Figure 1. The 18-pin Connector on the GV600MA ............................................................................ 4 Figure 2. Open the Case .................................................................................................................... 6 Figure 3. SIM Card Installation .......................................................................................................... 7 Figure 4. Backup Battery Installation ...............................
GV600MA User Manual 0. Revision History Version Date Author Description of Change 1.
GV600MA User Manual 1. Introduction The GV600MA compact waterproof GPS trackers designed for a wide variety of vehicle tracking applications. They have multiple I/O interfaces that can be used for monitoring or controlling external devices, including a 1-wire interface used for temperature monitoring. Bluetooth 4.0 is supported. Virtual ignition detection and i-Button function are both supported by GV600MA. Their built-in GPS receiver has superior sensitivity and fast initial positioning.
GV600MA User Manual 2. Product Overview 2.1. GV600MA Products Table 3. Product Model Model No. Region Technology Operating Band (MHz) GV600MA North America LTE LTE: B2/B4/B12/B13/B5 2.2. Parts List Table 4. Parts List Name Description GV600MA Locator 135*62*38 mm User Cable GV600MA standard cable USB Configure Cable USB to TTL serial port Power & GND Cable GV600MA Power &GND Cable Temperature Sensor GV600MA Temperature Sensor Fuel Level Sensor RS232 DUT-E 2.3.
GV600MA User Manual 8 GND External Accessory Ground 9 1_WIRE Temperature Sensor Input 10 NC NC 11 OUT/IN1 Negative trigger input1 for normal use or Open drain output1 150mA max drive current 12 OUT/IN2 Negative trigger input2 for normal use or Open drain output2 150mA max drive current 13 OUT/IN3 Negative trigger input3 for normal use or Open drain output3 150mA max drive current 14 OUT/IN4 Negative trigger input4 for normal use or Open drain output4 150mA max drive current 15 EX_RX U
GV600MA User Manual 3. Getting Started 3.1. Open and Close the Case Open the Case To open: Use a cross screwdriver to loosen the four screws and then lift the top case gently. To close: Align the top case with the bottom case and then tighten the four screws. Note: Pay attention to the following details to close the case. Otherwise, the waterproof capability of the device may be deteriorated. 1.
GV600MA User Manual 3.2. Install a SIM Card Open the case and ensure the unit is powered off (unplug the 18-pin cable and switch the internal battery to the OFF position). Insert the SIM card into the holder. Take care to align the cut mark and ensure the SIM card is pushed into the SIM holder completely. Close the case. Figure 2. SIM Card Installation 3.3. Install the Internal Backup Battery GV600MA has an internal backup Li-ion battery (5200mAH). Figure 3.
GV600MA User Manual 3.4. Power Supply Connection PWR (pin 1 or pin 2)/GND (pin 3 or pin 4) are the power input pins. The input voltage range is from 8V to 32V. The device is designed to be installed in vehicles that operate on 12V or 24V systems without the need of external transformers. Figure 4. External Power Supply Connection 3.5. Ignition Detection Table 7. Electrical Characteristics of Ignition Detection Logical Status Electrical Characteristics Active 5.
GV600MA User Manual position of the vehicle ignition switch as shown above. An alternative to connect to the ignition switch is to find a non-permanent power source that is only available when the vehicle is running, for example, the power source for the FM radio. IGN signal can be configured to transmit information to the backend server when ignition is on and enter the power saving mode when ignition is off. 3.6. Digital Inputs There are four general purpose digital inputs on GV600.
GV600MA User Manual 3.7. Analogue Inputs There is one analogue input on GV600MA, and the analogue input voltage range is from 0 to 32V. The following picture shows the recommended connection. Figure 7. Typical Analogue Input Connection Note: Pin 6 is a multifunction pin: it can be configured as an analogue input. 3.8. Digital Outputs There are four digital outputs on GV600MA. All are of open drain type and the maximum drain current is 150 mA. Each output has a built-in over current PTC resettable fuse.
GV600MA User Manual Figure 9. Typical Connection with a Relay Figure 10. Typical Connection with a LED Figure 11.
GV600MA User Manual Figure 12. Typical Connection with Other Devices Note: 1. OUT1 will latch the output state during reset. 2. Pay attention to the polarity of the relay if it is pre-installed with an internal flyback diode during connection. Install an additional diode externally if there is no pre-installed internal diode. A common diode such as a 1N4004 one will work in most circumstances. 3.9. Device Status and LED Table 10.
GV600MA User Manual Figure 13. GV600MA LEDs on the Case Note: 1. CELL LED cannot be configured. 2. GPS LED and PWR LED can be configured to turn off by using the configuration tool. 3. Fast flashing: for CELL LED is about 100ms ON/800ms OFF; for GPS LED and PWR LED is about 100ms ON/100ms OFF. 4. Slow flashing: for CELL LED is about 100ms ON/2000ms OFF; for GPS LED and PWR LED is about 600ms ON/600ms OFF. 3.10. Temperature Sensor Interface Figure 14.
GV600MA User Manual 3.11. Serial Port/UART Interface There are two lines dedicated to the Serial Port/UART interface (TXD and RXD). TXD and RXD are standard TTL signal. Figure 15.
GV600MA User Manual 4. Support Peripheral list Name Description Temperature Sensor GV600MA Temperature Sensor Fuel level sensor Digital RS232 (DUT-E COM Protocol) 4.1. Bluetooth The device role of Bluetooth could be Master and Slave. When the device role is Slave, the device will provide below services: device information service, battery information service, virtual serial port service. Other devices can read or use these services after connecting devices.
