QUASAR SCIENCE R2 LED Linear Light Download Full Manual at QUASARSCIENCE.
What’s in the Box 1 - R2 LED LINEAR Light with Ossium Rail (Q25R2 shown) 2 - Silicon Bumpers 1 - 8ft AC Power Cable 1 - 8ft DC Power Cable: P-TAP to 2.
R2 Overview *Q25R2 shown as reference Lens Hatch Power Side End Cap Ossium Mounting Points (White Hexagons) 1/4-20 Threaded Mounting Holes Ossium Rail Slim Diffuser Heat Sink Control Side End Cap 2
R2 Interface Layout Control Side End Cap 3 “Link” Button “Output” Button “Left / -” Button LED Screen “Enter / Set” Button “Right / +” Button Power On / Off “Data” Status Light “Wireless” Status Light USB-C Update Port DMX OUT LAN1 / DMX IN DC IN Port - 2.1mm x 5.
Mounting R2 Mount Dual Screw Baby Pin directly to lamp Mount Dual Screw Baby Pin to Ossium Rail Slider for added convenience and versatility Mount Rotator Block directly to lamp *Rotator Blocks sold separately Mount Rotator Block to Ossium Rail Slider for added convenience and versatility *Rotator Blocks sold separately 4
Getting Started •To set the Intensity, Color Temp, +/- Green, Saturation and Hue: 1. Press or until desired function is shown on screen, and press 1. to select. > Intensity < 100% 2. Intensity 87% < 4. > Intensity 100% < 2. The selection carets “> <” will move from the “>Function<” to the “>Value<”. 3. Press or to set the value. Press to save. 4. The selection carets “> <” will move from the “>Value<” back to the “>Function<”. 3.
Key Interface Power Button: Lamp on: Press and hold for 1 second. Lamp Off: Press and hold for 2 seconds. Output Button: Toggle the button to enable/disable lamp output for manual mode operation. Change the color/intensity without the change affecting the environment. Link Button: Press and hold to unlink lamp. Double Tap to bring up Wireless Menu (Pg 13.) Left / Minus Button: Decrease a value or navigate Left. Right / Plus Button: Increase a value or navigate Right.
Status Lights The Data and Wireless Status Lights can be various colors based on the connection type and status. Check that the lamp is in the correct wired and wireless modes and that Status lights are enabled in the config. See Page 8 for color combinations. Data LED Data Data Wireless LED Solid LED – Data Received. Solid LED – Connected to Wireless Device. No Light – No Data Received or Status Lights turned off. Slow Flashing – Lamp is paired with Wireless Device, but device is not found.
Status Lights Data Manual Mode Data: Off / Wireless: Off Data DMX Mode / Data Received Data: Red / Wireless: Off Data Ethernet Mode / Data Received Data: Yellow / Wireless: Off Data Wired Leader (Lead/Follow Mode) Data: Green / Wireless: Off Data Wired Follower (Lead/Follow Mode) Data: Cyan / Wireless: Off *Check Status Lights are enabled in Config Data Wireless DMX Data:Red / Wireless: Green (Or Universe Color) Data Wifi Mode (Art-net over Wifi) Data: Yellow / Wireless: Magenta Data Bluetooth Mode D
Button Shortcuts Min / Max Value Jump: On parameter menus such as Intensity, Color Temperature, Saturation, Hue, and Effects Parameters. While pressing and holding to increase the value, tapping While pressing and holding to decrease the value, tapping Enable/Disable Status Lights: Press and hold Enable/Disable RDM: Press and hold Link Button: Press and hold Wireless Menu: Double press 9 will jump to the next value or minimum value. for 5 seconds to disable the status lights.
Main Menu - Manual Mode > Intensity 0 to 100% in 1% increments > Color Temp 1750K to 10,000K > +/- Green 100M to 0G to 100G > Saturation 0 to 100% by 1% increments > Hue 0° to 360° > CT Preset 3200K - 4000K - 5000K - 5600K - 6000K - 2000K - 2800K > Color Preset Red - Orange - Yellow - Green - Cyan - Blue - Violet - Magenta > Effects Rainbow - Short Circuit - Paparazzi - Strobe - Fire - Emergency Lights - TV - Demo* (See Page 17-18) > Config Lamp Settings (See Page 11) *Check the website fo
Config Menu > DMX Channel > Number of Pixels > Profile > Wired Settings > Wireless Settings > Lead / Follow > Output Mode > Rig Mode > Status Lights > Languages > Lamp Hours > Update Firmware > Firmware > Reset to Default 11 Set the DMX Channel. Control the light as groups. (See Page 12) Set the DMX profile for the light. (See Page 18-23) Select the Wired data options to control the light. (DMX, Art-Net, sACN) (See Page 13) Select the Wireless data options.
Pixel Selection > Number of Pixels 1, 2, 5,10 - These are the available grouping options for the Q25R2’s 10 individually controllable pixels. 1, 2, 3, 4, 6, 8, 12, 24 - These are the available grouping options for the Q50R2’s 24 individually controllable pixels. 1, 2, 3, 4, 6, 8, 12, 16, 24, 48 - These are the available grouping options for the Q100R2’s 48 individually controllable pixels. •When choosing DMX profiles, each group of parameters are repeated per pixel except for the FX Parameters.
Wired Control Menu 13 > Wired Mode > DMX > Ethernet > DMX Settings > DMX Channel > Terminate > Ethernet Settings > View IP Address > IP Address Mode > DHCP (Auto) > Static > IP Address, Subnet Mask, Gateway > Universe > DMX Channel > Ethernet Mode Choose DMX512 or Ethernet Mode to Wire Control the light. Control the lamp with DMX512. Control the lamp with sACN or Art-Net. Set the DMX Channel 001 to 508 (Does not allow address to be outside of 512). Terminate the DMX Signal when last in line.
Wireless Control Menu > Wireless Mode > Wireless DMX > Bluetooth > Wifi > Off > Wireless DMX Settings* > Wifi Settings* > Bluetooth Settings >Reset > Status Lights On/Off > Reset Wireless Settings to Default Lumen Radio CRMX wireless DMX. Press and hold to Clear. Tap transmitter to pair. Connect to the lamp over Bluetooth. Connect to a wireless network to receive Art-Net over Wifi. Turns off all Wireless functionality. Shows the Hardware and Firmware of the CRMX TimoTwo.
Lead/Follow Mode •Lead/Follow mode allows one lamp to control many lamps at once. The Lead transmits DMX data wired or wirelessly to the Follows. When the Lead changes levels, the Follows will change as well. This applies to on board FX as well. •To use Lead/Follow mode, go to Config -> Lead/Follow. Set the leader to Lead and set all of the followers to Follow 1 to match the leader. Follow 2-8 are used with effects to do the same effect with different timings.
Output Mode •There are 3 different Output Modes, which are used to increase the light output or the resolution in different areas of the dimming range. > Output Mode Normal Output: Normal Operating Temperature, standard lamp output. High Output: High Operating Temperature, maximum output. Low Output: Gives maximum resolution in the low dimming section of the lamp. Maximum power is about 25% of High Output. Rig Mode •Rig mode is used to define how you want to turn on the lamp.
Effects (Manual) Main Menu 17 Effects Parameters Effect Result Item Result Rainbow Scroll through the hue from 0° at full saturation Effect Choose effect Short Circuit Lamp is on with random bursts of turning off Intensity Set Intensity of effect Paparazzi Lamp is off with random flashes of turning on Color Temp Set base color temp Strobe Rhythmic flashes on +/- Green Set +/- green of the color temp Fire A fire flicker effect Saturation Saturate the effect Emergency Lights Flashi
Effect Controls (Manual) Fire Submenu Emergency Light Submenu Weight Result Item Result Rate 0-200% for the speed of the effect Pattern Single, Double, Triple, Quad 100% is normal speed Color Presets R&B, B&B, R&32, R&56, B&32, B&56 Maximum Highest intensity level of effect Minimum Lowest intensity level of effect Weight Low, Centered, High Preset +/-400k Color at 2400k, 3200k,4000k, 5600k R&B&32, R&B&56 Color 1 & 2 Red, Orange, Yellow, Green, Blue, Magenta, 2000k, 3200k, 4000k, 5600k,
DMX Profiles (Overview) DMX Profiles (Basic) Profiles 1 - 8 Profiles 13, 14 Different DMX channel arrangements to control the Parameters for your lamps. Direct control of the 5 available colors channels; Red, Green, Blue, 2000K, 6000K DMX Profiles (FX) Profiles 9 - 12 Control the basic parameters of the lamp and allow control of the built-in effects of the lamp.
DMX Profiles (Basic) When using as more than one pixel, 1 additional channel group must be add be added per additional pixel.
DMX Profiles (Basic) Parameters Available Parameters based on Profile Parameter DMX Value Intensity 0-255 Color Temp 0-255 +/- Green Value +/- Green Control DMX Values DMX Value % Effect 0 - 100% 0-10 0-4 No Effect 2000K-6000K 11-20 5-8 Full Minus Green See Chart at right 21-119 8-46 -99% to -1% Hue 0-255 0° - 360° 120-145 47-57 Neutral Saturation 0-255 0 - 100% 146-244 57-96 1% to 99% Crossfade 0-255 0 - 100% 245-255 96-100 Full Plus Green Red 0-255 0 - 100% Gree
DMX Profiles (FX) When using as multiple pixels, patch in a fixture for each set of channel per pixel. The FX parameters are for the entire light.
DMX Profiles (FX) Parameters Parameters Effects Parameters Effect DMX Value % Item Result OFF 0-27 0 - 10 Effect Choose effect Rainbow 28-38 11-15 Intensity Set intensity of effect Short Circuit 41-53 16-20 Color Temp Set base color temp Paparazzi 54-68 21-25 +/- Green Set +/- green of the color temp Strobe 69-78 26-30 Saturation Saturate the effect Fire 79-91 31-35 Hue Set the hue Emergency Lights 92-104 36-40 Rate Demo 105-116 41-45 0-200% for the speed of the e
DMX Profiles (Extended FX) When using as multiple pixels, patch in a fixture for each set of channel per pixel. The FX parameters are for the entire light.
Basic Specifications 25 Model Q25R2 Q50R2 Q100R2 Wattage Max 25 watts Max 50 watts Max 100 watts Weight 1.76 lbs (0.8 kg) 3.3 lbs (1.5 kg) 5.84 lbs (2.64 kg) Dimensions 23 x 1.75 in (584.2 x 44.5 mm) 46.9 x 1.75 in (1161.7 x 44.5 mm) 90.86 x 1.75 in (2400 x 44.5 mm) Power Consumption 120v = 0.22 amp 240v = 0.11 amp 120v = 0.44 amp 240v = 0.22 amp 120v = 0.88 amp 240v = 0.44 amp 12v = 1.90 amp 24v = 0.95 amp 12v = 3.80 amp 24v = 1.90 amp 12v = 7.60 amp 24v = 3.
Warranty 3 Year warranty from date of purchase. Customer must provide proof of purchase. This warranty is transferable. Quasar Science will pay for: The replacement parts, repair and/or labor costs to correct defects in materials and workmanship. *Service must be provided by Quasar Science or an Authorized Quasar Science Service Center* Quasar Science will not pay for: Damage resulting from accident, misuse or abuse. Acts of God. Any failure that occurs for any other reason than materials and workmanship.
R2 LED Linear Light Quick Start Guide Please do not return your light to your retailer. Contact Quasar Science with any questions, problems or concerns. | 687 S. Anderson St. Los Angeles, CA 90023 info@quasarscience.com QUASAR SCIENCE (800) 876-0665 QUASAR Please check at QuasarScience.com/Support for firmware updates and up-to-date downloadable Quick Start Guide. V1.
