Thanks for buying the KG-699E series transceiver. This transceiver offers latest in design, multi-functionality, stable behaviour and easy operation. We believe you will be pleased with the high quality and dependable features for all your communication needs.
User Safety, Training, and General Information READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION BEFORE USING YOUR PORTABLE TWO-WAY RADIO. Compliance with RF Energy Exposure Standards Your two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy.
farther away from your head. Body-worn operation Always place the radio in a approved clip, holder, holster, case, or body harness for this product. Use of non- -approved accessories may exceed FCC RF exposure guidelines. Antennas & Batteries • Use only approved, supplied antenna or approved replacement antenna. • Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations. • Use only approved, supplied batteries or approved replacement batteries.
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfu l interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following Measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
Contents Unpacking and checking of your equipment Supplied accessories Description of functions Getting started LCD display Description of transceiver Speed search DTMF encoding Switch working mode Shortcut operation sheet How to operate Lock menu function Setting dual standby (TDR) ---- MENU O Setting channel step (STEP) ---- MENU 1 Setting squelch level (SQL-LE) ---- MENU 2 Setting batterypack savemode (SAVE) --- MENU 3 Selecting transmitpower (TXP) ---- MENU 4 Setting voice encrypt compress (SCR)--- ME
Contents Emergency calling type (EMC-TP)---MENU 28 Emergency calling channel (EMC-CH)---MENU 29 Select ringmode (RING-M)---MENU 30 Setting ringtime(RING-T)---MENU 31 Edit channelname (CHNAME) ---- MENU 32 Setting transmit segment when in dual standby (TDR-AB) ---- MENU 33 Setting A segment channel display mode (CA-MDF)---MENU 34 Setting B segment channel display mode (CB-MDF)---MENU 35 Setting keyboard lock (AUTOLK) ---- MENU36 Setting power on message (PONMSG) ---- MENU 37 Setting sidekey 1(PF1)---MNEU 38
Unpacking and checking of your equipment Carefully unpack the transceiver. We recommend that you identify the items in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, please notify your dealer.
Description of functions 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 03 Channel name edit available. Channel order, channel frequeny, channel name multi-display method Reverse frequency function Distant urgency alarm function Multi scan function Channel steps (5/6.25/10/12.5/25KHz) High/Low power changeable when on transmitting. Intelligentcharger ( Warning sound and dualcolor light) TX/RX splitselection (0-99.
Getting started Description of transceiver (Double knob) Topkey: Distant urgency alarm Channel switch Antenna Powerswitch / Volumecontrol B channel receive and transmit light A channel receive and transmit light A or B channel switchkey Screen / LCD display Numberkey Exitkey Reverse frequency / Scankey KG-699E Functionkey 2 4 5 6 0 7 8 9 # Lockkey Up /Downkey 05 Professional FM Transceiver PTT (Push-To-Talk) key Sidekey 1: radio/CALL/ NO-SUB/JP-PRI/JP-EMC Speaker/ Microphonejacks Batter
Getting started Speed search When setting each function or parameter, press the or key one time can speed search the function or parameter. DTMF encoding This transceiver has DTMF encoding. By pressing the right number key on transmit you can choose the right DTMF tone which you want to TX. A B C D Switch working mode + POWER ON Channel mode Frequency mode If you want to transmit the 1750Hz burst tone, you just press PTT and sidekey 1 at the same time.
Shortcut operation sheet 9 Setting auto back light 9 Press or key Select parameter ON: Turn on auto back light OFF: Turn off auto back light EXIT P19 -20 0 Press or key Select parameter 50 groups CTCSS (67 -254.
Shortcut operation sheet 27 Setting signal information 2 7 Press or key 15 groups signal Select parameter information 28 Emergency calling type 2 8 Press or key Select parameter 29 Emergency calling channel 2 9 0 ABR 30 Select ringmode EXIT P34 EXIT P34 Press or key 200 groups calling channel Select parameter EXIT P35 Press or key 4 kinds of ringmode Select parameter SOUND/BIV/BOTH/OFF EXIT P35 3 kinds of emergency alarm ALARM: Field alarm ENI: Distant alarm BOTH: Field + distant ala
Shortcut operation sheet 44 Setting memory channel 4 4 Press or key Select parameter 200 channels EXIT P46 -47 45 Delete channel 4 5 Press or key Select parameter 200 channels EXIT P48 46 Frequencyshift direction 4 6 Press or key Select parameter +: Positive offset - : Negative offset. OFF: Turn off frequencyshift direction EXIT P48 47 Offset frequency 4 7 Press or key Select parameter From 0 to 99.
How to operate In standby, press Press and number 0 and the screen will display enter, arrowhead aim at "ON" position, press OFF turn off dualstandby. Press NOTE / select ON turn on dualstandby or to confirm, then press to return to standby. ! Standby time is set by auto-backlight. (See MENU 9) Setting channel step (STEP) ---- MENU 1 In standby, press and number and the screen will display Press enter, arrowhead aim at "5.
How to operate Setting batterypack savemode (SAVE)--- MENU3 In standby, press + number and the screen will display Press enter, arrowhead aim at "OFF" position, press Press to confirm, then press / select one of 1:1/ 1:2/1:3/1:4/OFF. to return to standby. 1:1/1:2/1:3/1:4 means the radio receive circuit turn on and off pulse ratio.
How to operate Setting VOX (VOX) ---- MENU 7 In standby, press Press + number 7 and the screen will display enter, arrowhead aim at "OFF" position, press the 1 to 10 different sensitivity-levels. Press NOTE / to select VOX OFF or to switch on to confirm, then press to return to standby. ! When level is too high the VOX needs more volume to get activated. When scan or radio is in using, you can not use VOX function.
How to operate Setting receive DCS (R-DCS) ---- MENU 11 In frequencymode, press Press + number and the screen will display enter, arrowhead aim at "OFF" position, press one of the steps from D023N to D754I. Press NOTE / and select OFF to switch off DCS or to confirm, then press to return to standby. ! This transceiver has 105 groups different DCS codes, see appendix (2) DCS frequency sheet. And DxxxN means positive code, DxxxI means negative code.
How to operate Setting beepprompt function (BEEP) ---- MENU 15 Beepprompt is to tell you if the transceiver is operating well or has a malfunction. We kindly advice you to switch on this function. This function will inform you for any possible malfunction. In standby, press Press + number 5 and the screen will display enter, arrowhead aim at "ON" then press want to switch off the beep. Press NOTE / to switch on the beep or OFF when you to confirm, then press to return to standby.
How to operate Adding channelscan (SC-ADD) ---- MENU 19 This function ensure that whether frequency or channel be added to scan list or not. In frequencymode, press + number ABR 9 and the screen will display Press enter, arrowhead aim at "ON" position, press Press to confirm, then press / and select ON or OFF. to return to standby.
How to operate Setting scanmode (SC-REV) ---- MENU 22 This transceiver will stop scanning when detect the frequency(memory channel) of signal.According to the method of restoring that you choose,the transceiver will resume or stop scanning. The transceiver has three scanmodes. TO: After signal in channel disappears the transceiver will start scanning if without any operation within 5 seconds. CO: After the transceiver stopped on a signal it will resume scanning again in 3 seconds when signal disappears.
How to operate X XXXX Grouplist A unique ANI ID CODE 1 to 9 groups Edit method: see to the MENU 48. NOTE From 0000 to 9999 maximum This is how to build up ANI. ! Every transceiver in the group needs a unique ANI ID CODE. 2. Setting all calls, group calls and selective calls. NOTE ! Using any transceiver of group must be set turning on WDTS optional signal. Setting WDTS optional signal, the details see to the MENU 23. 3. Setting mutemode must be set as AND,the details see to the MENU (24) 4.
How to operate DTMF, 2-TONES, 5-TONES. 1. When DTMF/2-TONES/5-TONES signaling is programmed in a frequency. Press PTT key to transmit DTMF/2-TONES/5-TONES signal. 2. When DTMF/2-TONES/5-TONES is set in a channel , the preset functions will be activated only when the matching DTMF/2-TONES/5-TONES signals are received. 3. Likewise, your signals will be received only by parties using the same DTMF/2-TONES/5-TONES. 4.
How to operate *OFF: The radio can’t transmits the ID code when turn off all. In frequency mode, press Press + number 2 and the screen will display 5 key enter, arrowhead aim at “OFF” position, press /OFF. Press to confirm, press / select one of BOT/EOT/BOTH to return to standby. Setting ANI ID CODE transmit (PTT-LT) ---- MENU 26 Setting ANI ID CODE on transmit is needed to send ANI everytime when you press your PTT key. 1-30: Permit transmit ANI delayed time from 1 to 30.
How to operate Emergency calling channel (EMC-CH)---MENU 29 Select any channel which have set for emergency calling. In standby mode, press + number 2 ABR and the screen will display 9 Press key enter, arrowhead aim at “CH-000” position, press Press confirm, then press / select the desired channel, to return to standby. Select ringmode (RING-M)---MENU 30 Setting calling ring means after the transceiver receive the matching signal, it will be announced from the speaker.
How to operate 2. Via keyboard of transceiver. Edit Channelname 1. At least one channel should have been stored. 2. The transceiver should be work in channelmode. 3. Enter the channelname edit menu, then press / to select character, press to select edit position. Edit step 1. If the transceiver works in frequencymode, set the workmode as NAME in the display then press and power on again. If the transceiver works in CH mode, then go through MENU 34 to set display to NAME. 2.
How to operate 2. Channelfrequency + Channelorder display mode Press enter, press / select FREQ and the screen will display Press to confirm, then press to exit. 3. Channelname + Channelorder display mode Press enter, press / select NAME and the screen will display Press to confirm, then press to exit. Channelname display mode: To operate this function you need to edit the channelname first or it will still display the channelorder. See details of channelname edit in MENU 32.
How to operate NOTE ! Manual lock: In standby, press # for more than 2 seconds will lock keyboard, release keyboard press # for more than 2 seconds.
How to operate NOTE ! to exit FM radio, please press sidedey 1 again. You can use the software to edit the channel of FM radio, make the radio can display the frequency and radio's name on LCD screen, after you have succeed in programming, press the sidekey 1 to turn on FM radio, now you not only can use the channel knob to switch channel, but also can use / to switch. If the radio don't have channel knob, you can use / to switch FM radio channel.
How to operate Press enter, arrowhead aim at “CONTIN” position. Press Press confirm, then press / select CONTIN/PRESS to return to standby. Selecting standby display color (WT-LED) ---- MENU 41 The transceiver has four colors available: BLUE / ORANGE / PURPLE/OFF In standby, press Press + number and the screen will display 4 enter, arrowhead aim at "PURPLE" position, press BLUE / ORANGE / PURPLE/OFF. Press / and select the desired color of to confirm, then press to return to standby.
How to operate Example: You want 450.025MHz for receive and 460.025MHz for transmit and stored in CH-20, then act as follows: 1. When the transceiver works in frequency mode, input 4 4 + , then press 2 0 or / voice prompt will tell you it is stored, press 2. Then input 4 0 6 0 will tell you it is stored + press 2 0 5 4 0 2 5 key select CH-20, press , + key to confirm, to exit; 5 + + 4 + 4 + + and voiceprompt to exit. 3. The dis-channel is stored.
How to operate In standby press Press + number 4 7 and the screen will display enter, press number 0 to 9 to select offsetfrequency. Press to confirm, then press to return to standby. The frequencyshift direction and offsetfrequency can only be programmed when the transceiver works in frequencymode, in order to let transmitting and receiving under different frequency. Follow the next steps: 1. Set working frequency. 2. Set frequencyshift direction and offsetfrequency.
How to operate Be careful, don't set VOX-T to a long time. This transceiver total has 20 levels, unit: 100ms In standby, press Press +number and the screen will display 0 5 enter, arrowhead aim at "5", press not allow delay transmit, press / and select one of level between 1 and 20 or 0 to confirm, then press to return to standby. Companding (COMP) ---- MENU 51 COMP: Use voice compress technology to reduce the noise when on talking, make the voice clear.
How to operate Lowvoltage batterypack voiceprompt When the batterypack has lowvoltage, the transceiver will sound "low batterypack"voice prompt. Setting transmit overtime prompt When transmitter works longer than preset time, the transceiver will announce "transmit overtime" by voice and stops transmitting. If you want to transmit again, please press PTT. (Setting overtime prompt please see MENU 6) Adding channelscan Edit method: Strictly via KG-699E programming software.
How to operate In frequencymode, order input + ; 3. Press press + 2 0 + 4 + 5 + 0 + 0 + 2 + . Voiceprompt transmit store, press 5 , + 4 + 4 key. , turn on the power at the same time, the transceiver work in channel mode at this time, / select channel 20, the transceiver can join repeater. How to use your intelligentcharger 1. When the poweradapter is connected the intelligentcharger, the poweradapter should be plugged into the matchingvoltage.
Trouble shooting Problem Possible Cause Possible Solution Keyboard and PTT 1. The keyboard is locked. 1. Set keyboard to free. switch do not work. 2. RADIO "mode" is switched on, see displayFM. 2. Please exit RADIO mode. If you have set transceiver to busychannel Switch off busychannel lockout. lockout. You can not store In channel mode or frequency+channel Set transceiver to frequency certain settings. mode you cannot set parameters. mode. The receivelight is on and you can not transmit.
Technology parameter Appendix 2 DCS 1 D023N 16 D074N 31 D165N 46 D261N 61 D356N 2 D025N 17 D114N 32 D172N 47 D263N 62 D364N 3 D026N 18 D115N 33 D174N 48 D265N 63 D365N 4 D031N 19 D116N 34 D205N 49 D266N 64 D371N 5 D032N 20 D122N 35 D212N 50 D271N 65 D411N 6 D036N 21 D125N 36 D223N 51 D274N 66 D412N 7 D043N 22 D131N 37 D225N 52 D306N 67 D413N 8 D047N 23 D132N 38 D226N 53 D311N 68 D423N 9 D051N 24 D134N 39 D243N 54 D315N 6
Technology specification Frequencyrange Memorychannels Voltage Working temperature Channels Poweroutput Mode Maximum deviation Adjacent channel power Stability Sensitivity Audio output power Weight Size NOTE UHF: 406.125-469.975MHz 200 channels 7.4V DC -30*(-22F) to +60*(140F) Co-channel or Dis-channel simplex UHF:4W F3E(FM) * ±5KHz < -60dB ±5 ppm < 0.2 µV *700mW 250g 62 X 105 X 39 (mm) 2.44x4.13x1.54(inch) ! Specifications are subject to change without notice.
Announce endeavors to achieve the accuracy and completeness of this manual,but is not liable for any possible omission and printing errors.All the above specifications are subject to change by without prior notice.
