User Manual

ManualsBrandsQuanzhou Skydroid Technology ManualsOtherQuanzhou Skydroid Technology R12 Receiver

A) Introduction

1. Product characteristic

1.1 Dual antenna plus Dual module with control of algorithm to ensure reliable

communication by full angle high gain antenna. Also thanks to latest

FHSS(Frequency Hopping Spread Spectrum)technology to achieve perfect control

of the FUAV and operation of camera.

1.2 Tx and Rx output sent flight data to ground station. Fully maximize advantages

of 2.4G to solve the unstable and interference problem of 433Mhz and 915Mhz

1.3 Integrated internal broadcast station

1.4 adjust parameter anytime through App (FUAV Helper)

1.5 Link by USB cable or Bluetooth. Also support S. Bus, PPM, PWM, I2C serial port

and expandable

1.6 Flight parameter can be adjusted through App in your phone. It can be linked

by either USB (with OTG) or Bluetooth. You can change any features over the App,

mode (mode 1, 2, 3,4) , Nor/Rev, failsafe,Sbus, ppm output and baudrate. Data is

saved so that you can use anytime.

1.7 Base on “Tower” App to make groundstation perfectly matched each other,

larger view on the map. So you may do point to point planning and self operation.

Also one key home return.

1.8 Internal 4000mah Li-ion battery can last for more than 25 hours with 100mw

Summary of content (8 pages)

PAGE 1
A) Introduction 1. Product characteristic 1.1 Dual antenna plus Dual module with control of algorithm to ensure reliable communication by full angle high gain antenna. Also thanks to latest FHSS(Frequency Hopping Spread Spectrum)technology to achieve perfect control of the FUAV and operation of camera. 1.2 Tx and Rx output sent flight data to ground station. Fully maximize advantages of 2.4G to solve the unstable and interference problem of 433Mhz and 915Mhz 1.3 Integrated internal broadcast station 1.
PAGE 2
low power consumption . Your phone can be charged through the micro USB port. 1.9 Highly integrated data, video and flight controller board. It makes the size smaller. Aluminium foldable mounting plate. With 360 degree adjustment. 1.
PAGE 3
. Reciever 3.1 Failure LED indication Red LED flash rapidly: receiver self detect fail, Sent it back to factory if retry fail. Red/Green LED flash alternately: receiver self detect succeed Green LED off but self detect is successful: turn on Tx and pair again No LED on: Check working voltage is 5v and polarity is correctly connected. Sent back to factory if retry failed. 4) R12 PRO、R12 connect to Android phone 4.1 correctly connect receiver and camera. Power on 4.2 install FUAV APK 4.
PAGE 4
.4 Click “Yes” , image will be shown on your phone
PAGE 5
) How to update firmware 5.1 Android upgrade 5.1.1 Open “Device Helper” and link up with Bluetooth. Press the button “A” while turn on the Tx. 5.1.2 Button “A” LED flashing slowly to enter download mode. Check if any new firmware update. 5.1.3 Refresh the firmware if any. 5.2 PC Upgrade 5.2.1 Please browse “www.fuav.xin to select download. 5.3 Tx Upgrade 5.3.1 Link up Tx and PC. Press button “A” while turn on the Tx. Button “A” LED flash slowly to enter download mode. 5.3.
PAGE 6
7) Frequent Question and Answer 7.1 Q: Does R12 PRO、R12 support PPM, Sbus? A: Yes, The first row pins default as Sbus, Change to PPM signal on the APK. 7.2 Q: How far can R12 PRO、R12 reach? A: Under the clean signal circumstances. Video signal can reach 20km while Data signal Can be 30km. 7.3 Q: How to define two antenna on R12 PRO、R12 A: Dual antenna are 2.4Ghz, also dual module inside for transmission. 7.
PAGE 7
PIX flight controller board. Also the other groundstation Map come with flight controller board. 7.9 Q: How to turn off/On the Tx A: Short press the power button then long press to turn on the Tx and vice versa 7.10 Q: Fail to unlock the flight controller? A: 7.11 Q: No LED on receiver when link with the flight controller? A: Turn on the Tx, if still no signal please check the battery level and pair again 7.12 Q: Change hand Mode A: Open “Device Helper” to change the hand mode 7.
PAGE 8
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.