QT‐AD10A15Transmitter Description This document describes the use of the QT‐AD10A15A/C transmitter.
QT‐AD10A15Transmitter Family QT‐AD10A15TRANSMITTERFAMILY Contents QT‐AD10A15 Transmitter Family ............................................................................................................. 1 FCC Notices: .................................................................................................................................. 3 AD10 Transmitter Family ..........................................................................................................................
QT‐AD10A15Transmitter Family FCC Notices: Information to users: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1.) This device may not cause harmful interference, and (2.) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
QT‐AD10A15Transmitter Family Innovation, Science and Economic Development Canada (ISED) This device contains licence‐exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence‐exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
QT‐AD10A15Transmitter Family AD10 Transmitter Family Introduction The AD10 transmitter family is made up of the following models; QT‐AD10 PlayerMic S QT‐AD10 PlayerMic QT‐AD10 AquaMic QT‐AD10 AquaMic L QT‐AD10 CoachMic QT‐AD10 RefMic QT‐AD10 RefMic HD QT‐AD10 BeltMic QT‐AD10 Incognito QT‐AD10 GolfCupMic QT‐AD10 tapshoeMic QT‐AD10 BouyMic 5
QT‐AD10A15Transmitter Family AD10 series bodypack transmitters deliver impeccable audio quality and RF performance with wide‐ tuning, High Density (HD) mode, and encryption. The transmitter Transmitterfeatures durable metal construction, and single pin Lemo connector. The Q5X remote control system is referred to as RCAS, Remote Control Audio System. Q5X pioneered wireless remote control for transmitters in 2009.
QT‐AD10A15Transmitter Family Features Performance 20 Hz to 20 kHz range with flat frequency response Automatic input staging optimizes gain setting AES 256‐bit encryption‐enabled for secure transmission >120 dB dynamic range 100 meter (300 feet) line‐of‐sight operating range Selectable modulation modes optimize performance for spectral efficiency o Standard – optimal coverage, low latency o High density – dramatic increase in max system channel count Built‐in tone generator and RF markers
QT‐AD10A15Transmitter Family Standby Mode In this mode the AD10 Transmitter is transmitting a 2.4 GHz heart beat every 1.5 second, and the Transmitter is not transmitting UHF audio. The Heart beat contains configuration data, such as current RF frequency, Output power, and Mic Off‐set, and the heart beat also contacts current status information such as battery level, Mute status and 2.4 GHz channel.
QT‐AD10A15Transmitter Family Power either ON or OFF, this is the transmitter’s power state and can be changed here. Frequency can be adjusted by moving the cursor to the value using the navigational arrows then pressing “ENTER” button. This will bring up the screen shown below on the left. To change the MHz values use the UP/DOWN arrows. To edit the frequency’s kHz, press the “RIGHT” button to highlight them then use the “UP/DOWN” arrows again.
QT‐AD10A15Transmitter Family Groupis the group number (1‐16) to which the transmitter belongs, allowing it to be controlled with group commands (see Group Commands below). To change the group that the transmitter belongs to, select the transmitter, then the add it to the desired Group number. From here the number can be adjusted using the “UP/DOWN” arrows. Once satisfied, press “ENTER” or “BACK” button and select “Save” when prompted. RF Poweris the power setting of the RF output of the transmitter.
QT‐AD10A15Transmitter Family Specifications Encryption AES 256 Encryption Audio Frequency Response 20 Hz – 20 KHz Mic Offset Gain Range ‐12 to 21 dB (in 1 dB steps) Pre‐amplifier Equivalent Input Noise (EIN) System Gain Setting ≥ +20 ‐115 dBV, A‐weighted, typical Maximum Input Level 1 kHz at 1% THD, 3dBv (5.0V) Input Impedance: 8.2K with 5V Mic Bias Audio Input Connector Single pin Lemo connector, Lemo part number PCS.01.250.
QT‐AD10A15Transmitter Family Frequency Bands (Depends on model) Band Frequency Range (MHz) G56 470 to 636 G57 470 to 616* K55 606 to 694 X55 941 to 960 *with a gap between 608 to 614 MHz. **with a gap between 608 to 614 MHz and a gap between 616 to 653 MHz. *** Refer to the corresponding FCC/ISED Grants for details of frequencies authorized for use. LICENSING INFORMATION Licensing: A ministerial license to operate this equipment may be required in certain areas.
