Quick Start Guide

ManualsBrandsQuantum ManualsHome building and DecorSuperLoader 3

www.quantum.com

SuperLoader

SuperLoader™ 3

Quick Start Guide

The Quantum

SuperLoader 3 is an automated storage and retrieval device

consisting of a tape drive and up to two tape magazines holding up to

eight cartridges each.

For more information, see the Quantum SuperLoader 3 User’s Guide

(PN 81-81317) on the documentation CD provided with your autoloader.

This quick start guide uses the following conventions:

Note: Notes emphasize important information related to the main topic.

Caution: Cautions indicate potential hazards to equipment and are

included to prevent damage to equipment.

WARNING: Warnings indicate potential hazards to personal safety and

are included to prevent injury.

This document explains how to unpack the SuperLoader 3 and install it in a

standard 19-inch rack.

Contents

Choosing a Location.............................. 1

Preparing for the Installation................ 2

Providing Necessary Tools ................. 2

Taking ESD Precautions .................... 3

Preparing for Rack Mounting............ 3

Unpacking the Autoloader .................... 4

Checking Accessories......................... 5

Rack Mounting the Autoloader............. 6

Autoloader Panel Overviews ............... 12

SCSI Bus Requirements........................ 13

General Information........................ 13

Connecting SCSI, SAS, or

Fibre Channel and Power Cables......... 13

Setting the SCSI ID .............................. 16

Preparing the Host and Verifying

the Connection ................................. 16

Operating System Support.................. 17

Autoloader Device Driver ................ 17

Tape Drive Device Driver.................. 17

After the Installation ........................... 18

Summary of content (18 pages)

PAGE 1
SuperLoader Contents Choosing a Location.............................. 1 Preparing for the Installation ................ 2 Providing Necessary Tools ................. 2 Taking ESD Precautions .................... 3 SuperLoader™ 3 Quick Start Guide Quantum® The SuperLoader 3 is an automated storage and retrieval device consisting of a tape drive and up to two tape magazines holding up to eight cartridges each.
PAGE 2
SuperLoader 3 Quick Start Guide Choosing a Location The autoloader is designed to fit in a standard 19-inch rack using either the long or short brackets (depending on the depth of the rack). The autoloader uses standard rack mounting hardware.
PAGE 3
SuperLoader • Preparing for Rack Mounting Providing Necessary Tools Provide the following tools for unpacking and installing the autoloader: • #2 Phillips screwdriver • Level • Antistatic wrist strap Taking ESD Precautions Some components within the autoloader contain static-sensitive parts. To avoid damaging these parts while performing installation procedures, always observe the following precautions: • Ensure that the work area is free from conditions that could cause electrostatic discharge (ESD).
PAGE 4
SuperLoader 3 Quick Start Guide 4 Verify that the total current of all rack mounted components (including the autoloader) will not exceed the current rating of the power distribution unit or outlet receptacles. 5 Secure the help of at least one other person. At least two people are required to safely install the autoloader into a rack cabinet. WARNING: Failure to take these safety steps may result in personal injury or equipment damage.
PAGE 5
SuperLoader 5 Remove the foam insert from the magazine bay of the autoloader. Save the packing materials in case you need to move or ship the autoloader in the future. Note: If the cover must be taken off, there are 26 screws that need to be removed.
PAGE 6
SuperLoader 3 Quick Start Guide Figure 1 Rack Mount Hardware Support brackets (74-60605-01) Short autoloader brackets (72-A225-A) Long autoloader brackets (72-A226-A) Support bracket screws 72-A348-A (4) or 90-60227-50 (4) Rack Mounting the Autoloader This section provides the steps for attaching the autoloader directly to the stationary rails of a rack. Refer to table 1 for information on common rack hole types.
PAGE 7
SuperLoader Figure Description Threaded holes require neither cage or clip nuts to accept mounting hardware. Note: The rails within the rack have a hole pattern that repeats throughout the rail. 1 Install two clip nuts, 1.75 in. (44.45 mm) apart, onto each of the four rails of the rack, making sure that you install each pair of clip nuts at exactly the same level (see figure 2). Figure 2 Installing Two Clip Nuts Rail Rail Clip nut Outer covers of the rack 1.75 in (44.
PAGE 8
SuperLoader 3 Quick Start Guide Figure 3 Attaching Autoloader Brackets Autoloader Screws (10-32 x 1/4 only) Autoloader bracket 3 Using rack screws, attach a support bracket to the clip nuts on each rear rail (see figure 4). Note: Be sure to attach the support brackets correctly; the side of the bracket with only two holes should be secured to the rail.
PAGE 9
SuperLoader Figure 4 Attaching Support Brackets Clip nuts Support bracket Rack screws Rear rail in rack Outer cover of rack 4 With the help of a second installer, insert the autoloader into the rack so that the autoloader brackets slide into corresponding support brackets on the rear rails and the tabs at the front of the autoloader align flush with the clip nuts on the front rails (see figure 5). Caution: Do not release the front end of the autoloader until it can be secured to the rack.
PAGE 10
SuperLoader 3 Quick Start Guide Figure 5 Sliding Autoloader into Rack Autoloader bracket Support bracket 5 While the other installer holds the front end of the autoloader, secure the front end of the autoloader to the rack using four rack screws (two per tab) as shown in figure 6. Tighten the screws just enough to secure the autoloader to the front rails.
PAGE 11
SuperLoader Figure 7 Connecting Support Brackets Support bracket Autoloader bracket Screws 7 Verify that the autoloader is level. Adjust as needed. 8 When the autoloader is level, tighten all screws securing the autoloader to the rack. This includes the following: • Four screws securing the autoloader tabs to the front rails. • Four screws securing the support brackets to the rear rails. • Four screws securing the autoloader brackets to the support brackets.
PAGE 12
SuperLoader 3 Quick Start Guide 4 Front panel LCD screen 5 Function keys 6 Left magazine (or blank) 7 Right magazine (or blank) The Ethernet connector on the back panel allows you to connect to the autoloader remote management interface.
PAGE 13
SuperLoader Note: The maximum number of autoloaders supported per SCSI bus is two. The autoloader may not work with multiple SCSI LUNs when attached to a RAID controller. The autoloader is not recommended for use with a RAID controller. If this situation occurs, it is recommended that the autoloader be attached to a separate SCSI bus controller on the host or server.
PAGE 14
SuperLoader 3 Quick Start Guide Figure 11 Cable Connectors (SAS Tape Drive) SAS cable Ethernet cable Figure 12 Cable Connectors (SCSI Tape Drive) SCSI terminator SCSI cable Ethernet cable If the supplied SCSI cable does not fit the connector on your SCSI host adapter, you either have an incompatible SCSI host adapter or you need to purchase a cable adapter. Contact your service representative or your SCSI host adapter manufacturer for information.
PAGE 15
SuperLoader Caution: Whenever you power cycle the autoloader, allow 10 seconds before turning the power back on. The power supply requires at least two to three seconds for the capacitors to discharge. This ensures a complete system reset on power down and may avoid system errors. 9 Turn on the autoloader by setting the power switch on the back panel to the ON position and pressing the power switch on the front panel.Turn on any other devices you turned off earlier.
PAGE 16
SuperLoader 3 Quick Start Guide Preparing the Host and Verifying the Connection If necessary, install a SCSI, Fibre Channel, or SAS host adapter, software, and compatible drivers. Refer to the manuals for the host computer and SCSI, Fibre Channel, or SAS host adapter for detailed instructions. In addition, follow these general guidelines: • When the host server is powered on, install software, and/or drivers that are compatible with the autoloader (see Windows Operating System Support).
PAGE 17
SuperLoader Note: Device drivers are required if you intend to use the Microsoft Windows native backup application. Commercial backup applications provide all necessary device driver support. Refer to www.quantum.com for a list of compatible backup applications. Please note that Microsoft Windows NT® does not include native support for autoloaders. A backup application must be used if using the SuperLoader 3 under Microsoft Windows NT.
PAGE 18
SuperLoader 3 Quick Start Guide • For the DLT-S4 drive, go to: http://www.quantum.com/ServiceandSupport/ SoftwareandDocumentationDownloads/DLTS4/Index.aspx#Drivers. After the Installation From the front panel of the autoloader, use the menus to set the IP address (DHCP or Static), Subnet Mask (if required), Gateway (if required), SNMP Server (optional), and Time Server (optional). The default IP address is 192.168.20.128. The default login and password for the On-board Remote Manager is guest and guest.