User's Manual

ManualsBrandsQuantum ManualsHome building and DecorSuperLoader 3

6-68059-01 Rev A, October 2013

*6-68059-01 A*

Scalar, DXi, StorageCare, StorNext, GoProtect, and Vision are registered trademarks of Quantum Corporation and its affiliates

in the United States and/or other countries. All other trademarks are the property of their respective owners. Quantum

specifications are subject to change.

Quantum SuperLoader 3

Magazine or Magazine Blank

Replacement

Follow the steps in the document to replace a magazine or magazine blank in

SuperLoader 3:

• Understand Magazine or Magazine Blank Orientation on page 1

• Removing a Magazine or Magazine Blank on page 5

• Replacing a Magazine on page 7

Understand Magazine or Magazine Blank Orientation

A magazine or magazine blank can be configured to fit in the right or left

magazine bay. The handle must be removed and the appropriate handle

attached to match the orientation of the magazine or blank.

To remove and attach a magazine handle, you will need a #1 Phillips

screwdriver.

Summary of content (8 pages)

PAGE 1
Quantum SuperLoader 3 Magazine or Magazine Blank Replacement Follow the steps in the document to replace a magazine or magazine blank in SuperLoader 3: • Understand Magazine or Magazine Blank Orientation on page 1 • Removing a Magazine or Magazine Blank on page 5 • Replacing a Magazine on page 7 Understand Magazine or Magazine Blank Orientation A magazine or magazine blank can be configured to fit in the right or left magazine bay.
PAGE 2
Quantum SuperLoader 3: Magazine or Magazine Blank Replacement 6-68059-01 Rev A October 2013 Figure 1 Left Magazine Orientation Outside edge view of left magazine Inside edge view of left magazine 2 Understand Magazine or Magazine Blank Orientation
PAGE 3
Quantum SuperLoader 3: Magazine or Magazine Blank Replacement 6-68059-01 Rev A October 2013 Figure 2 Right Magazine Orientation Outside edge view of right magazine Inside edge view of right magazine Understand Magazine or Magazine Blank Orientation 3
PAGE 4
Quantum SuperLoader 3: Magazine or Magazine Blank Replacement 6-68059-01 Rev A October 2013 Figure 3 Left and Right Magazine Blank Orientation Left magazine blank Right magazine blank Changing the orientation of a magazine 4 1 Remove the two screws that attach the handle to the front of the magazine.
PAGE 5
Quantum SuperLoader 3: Magazine or Magazine Blank Replacement 6-68059-01 Rev A October 2013 Figure 4 Removing the Screws from the Handle Screws 2 Unsnap the handle carefully, being careful not to break the hinge. 3 Rotate the magazine 180 degrees so that what was the front of the magazine is now the back. 4 Attach the appropriate left or right handle to the front of the rotated magazine. 5 Snap the handle back onto the front of the magazine.
PAGE 6
Quantum SuperLoader 3: Magazine or Magazine Blank Replacement 6-68059-01 Rev A October 2013 Note: Handles are either right or left. They are not interchangeable between the left and right sides of the autoloader. Removing a Magazine 1 On the menu, scroll to Commands. 2 Press Enter. 3 On the Commands sub-menu, scroll to Eject, and then press Enter. 4 On the Eject sub-menu, scroll to Right Magazine or Left Magazine, depending on which magazine you want to eject, and then press Enter.
PAGE 7
Quantum SuperLoader 3: Magazine or Magazine Blank Replacement 6-68059-01 Rev A October 2013 Figure 6 Tape access on a Magazine tape access Removing a Magazine Blank Your autoloader comes equipped with either two magazines, or one magazine and one magazine blank. The autoloader will not function without both magazine bays equipped with either a magazine or a magazine blank. 1 Pull the magazine blank straight out. 2 Replace with another magazine blank or a cartridge magazine (see Replacing a Magazine).
PAGE 8
Quantum SuperLoader 3: Magazine or Magazine Blank Replacement 6-68059-01 Rev A October 2013 8 Replacing a Magazine