3URGXFW 0DQXDO 3URGXFW 0DQXDO 3URGXFW 0DQXDO '/7 9 7DSH 'ULYH '/7 9 $
DLT-V4 Product Manual Guide, 81-81422-03 A01, October 2006, Made in USA. Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. COPYRIGHT STATEMENT Copyright 2006 by Quantum Corporation. All rights reserved.
Contents Preface Chapter 1 x Introduction 1 DLT-V4 Tape Drive Overview........................................................................................1 Features ..............................................................................................................................2 Firmware Upgrades and Drivers ...................................................................................2 Chapter 2 Installing the Internal SCSI Tape Drive 4 Equipment Required ...................
Contents Chapter 3 Installing the Internal SATA Tape Drive 16 Equipment Required...................................................................................................... 16 SATA Requirements ...................................................................................................... 16 Installation Steps ............................................................................................................ 17 Unpacking the Internal SATA Tape Drive ............................
Contents Chapter 6 Installing the Tabletop USB/eSATA Tape Drive 43 Equipment Required...................................................................................................... 43 USB Requirements.......................................................................................................... 43 eSATA requirements...................................................................................................... 44 Installation Steps ................................................
Contents Chapter 10 Specifications 64 Altitude ............................................................................................................................ 64 Dimensions and Weights .............................................................................................. 65 Temperature and Humidity Ranges............................................................................ 66 Functional Specifications............................................................................
Figures DLT-V4 Product Manual Figure 1 Rear Panel Connections for the Internal SCSI Tape Drive ................... 7 Figure 2 SCSI Interface — Terminator Installation ............................................... 9 Figure 3 SCSI Cable with Built-in Terminator ..................................................... 10 Figure 4 Removing the Workstation Cover (example) ....................................... 11 Figure 5 Installing the Internal SCSI Tape Drive in an Open Bay.....................
Figures DLT-V4 Product Manual Figure 19 SCSI ID Selector Switch ........................................................................... 38 Figure 20 Tabletop Tape Drive SCSI and Power Cable Connections ................. 39 Figure 21 Server SCSI Cable Connections .............................................................. 40 Figure 22 Tabletop SCSI Tape Drive Rear Panel Connections ............................ 41 Figure 23 Connecting the USB/eSATA Cables.....................................
Tables DLT-V4 Product Manual Table 1 Installing the DLT-V4 Internal SCSI Tape Drive — Overview .............. 5 Table 2 Selecting the SCSI ID .................................................................................... 7 Table 3 Installing the DLT-V4 Internal SATA Tape Drive.................................. 17 Table 4 Installing the DLT-V4 Internal SATA-to-USB Tape Drive.................... 24 Table 5 Installing the Tabletop SCSI Tape Drive................................................
Tables DLT-V4 Product Manual Table 18 Data Cartridge and Media Characteristics ............................................. 69 Table 19 Reliability Factors........................................................................................
Preface This document serves as an information source to familiarize Quantum customers and systems professionals with the DLT-V4 tape drive system. The DLT-V4 tape drive is an extension of the Quantum Digital Linear Tape (DLT®) product family. Purpose This document describes the DLT-V4 tape drive, listing its physical, functional, and performance specifications, and describing the standards that the tape drive meets.
Preface • Chapter 5, Installing the Tabletop SCSI Tape Drive, explains how to configure and install the tabletop SCSI tape drive. • Chapter 6, Installing the Tabletop USB/eSATA Tape Drive, explains how to configure and install the tabletop USB/eSATA tape drive. • Chapter 7, Installing the Device Drivers, explains how to download and install device drivers. • Chapter 8, Using Your Tape Drive, contains functional information useful during the operation of the tape drive in all of its configurations.
Preface • Left side of the drive — Refers to the left side as you face the component being described. • b — All binary numbers are succeeded by “b.” • h — All hexadecimal numbers are succeeded by “h.
Preface Related Documents Element Convention Example Dimensions in Figures No units specified (Inches understood unless otherwise specified) 0.57 EJECT DISTANCE The following documents are related to the DLT-V4 tape drive: Document No. Document Title Document Description 81-81209-xx 1U Rackmount Rail InstallationGuide Explains how to install the rails and how to install the 1U Rackmount unit into them.
Preface SCSI Standards Copies of the approved version of the SCSI standards may be obtained from: Global Engineering Documents 15 Inverness Way, East Englewood, CO 80112 (800) 854-7179 or (303) 397-2740 Contacts Quantum company contacts are listed below.
Preface 0 Global Services Quantum Global Services provides 24-hour support that can be reached at: North/South America: (949) 725-2100 or (800) 284-5101 Asia/Pacific Rim: APAC Headquarters: (International Code) + 65 6334 0660 Specific countries: www.quantum.com/ServiceandSupport/ ContactServiceandSupport/DLTSupportAPAC// Index.
Chapter 1 1 Introduction This chapter introduces the DLT-V4 tape drive (tabletop or internal), and provides a general overview of the product. DLT-V4 Tape Drive Overview 1 The Quantum DLT-V4 tape drive is a value-priced, high-reliability, highcapacity linear streaming data cartridge tape drive designed for use on entry- to mid-range computing platforms.
Chapter 1 Introduction Features Features 1 The DLT-V4 tape drive offers the following features: • Supported formats: DLT-V4 (read/write using DLTtape® VS1 Media data cartridges), DLT VS160 (read only using DLTtape VS1 Media data cartridges), DLT1/VS80 (read only using DLTtape IV data cartridges). • Uses DLTtape VS1 data cartridge. • 5¼-inch half-height form-factor. • Formatted data cartridge capacity of 160 GB native, 320 GB compressed.
Chapter 1 Introduction Firmware Upgrades and Drivers Firmware Upgrades and Drivers 1 Quantum frequently provides new and updated tools to use with its tape drives. These tools include such items as upgrades for product software and firmware, and diagnostic software that may be newly developed. All these tools are available on the Quantum Web site. To access these tools: 1 Go to the Quantum Web site: www.quantum.com. 2 Click SERVICE AND SUPPORT in the upper menu bar.
Chapter 2 2 Installing the Internal SCSI Tape Drive This chapter contains step-by-step instructions for installing the internal SCSI tape drive. Equipment Required 2 All you need to install the DLT-V4 internal SCSI tape drive is a PHILLIPS® screwdriver and adequate ESD protection.
Chapter 2 Installing the Internal SCSI Tape Drive Installation Steps If you attach the tape drive to a narrow (50-pin) SCSI bus, you must use a customer-supplied 68-pin to 50-pin adapter that terminates the unused 18 pins. These adapters are sometimes labeled high-byte termination.
Chapter 2 Installing the Internal SCSI Tape Drive Unpacking the Internal SCSI Tape Drive Unpacking the Internal SCSI Tape Drive 2 Before you do anything else, unpack and inspect the tape drive for shipping damage. If you notice any damage, report it both to the sales representative and to the shipping company immediately. Note: Save the packing materials in case you need to move or ship the tape drive in the future.
Chapter 2 Installing the Internal SCSI Tape Drive Setting the SCSI ID Figure 1 Rear Panel Connections for the Internal SCSI Tape Drive 68-pin high-density SCSI connector SCSI ID jumper block Drive power connector 2 Use the supplied jumpers to select the desired SCSI ID as shown in table 2: Table 2 Selecting the SCSI ID SCSI ID 0 1 2 3 4 5 (default) 6 7 8 9 10 11 12 13 14 15 Jumper Block SCSI ID Jumper Block SCSI ID Jumper Block SCSI ID Jumper Block DLT-V4 Product Manual 7
Chapter 2 Installing the Internal SCSI Tape Drive Terminating the Internal SCSI Tape Drive Terminating the Internal SCSI Tape Drive 2 If the tape drive is the only SCSI device attached to the selected server other than the SCSI host adapter, or if it is the last physical device on the SCSI bus (at the end of the SCSI chain), you must terminate it. If another SCSI device is the last device on the SCSI bus, confirm that it is properly terminated and do not terminate the tape drive.
Chapter 2 Installing the Internal SCSI Tape Drive Terminating the Internal SCSI Tape Drive Figure 2 SCSI Interface — Terminator Installation Terminator SCSI cable Note: DLT-V4 Product Manual If the SCSI cable that came with the SCSI host adapter already has a terminator built into it, do not use another terminator. Figure 3 shows an example of such a cable.
Chapter 2 Installing the Internal SCSI Tape Drive Installing the Internal SCSI Tape Drive Figure 3 SCSI Cable with Builtin Terminator Terminator SCSI cable (supplied with host adapter) Installing the Internal SCSI Tape Drive 2 To install the tape drive, follow these steps: 1 Shut down the operating system and power off the server or workstation. 2 Power off all peripheral devices, such as printers and other SCSI devices.
Chapter 2 Installing the Internal SCSI Tape Drive Installing the Internal SCSI Tape Drive 3 Remove the cover from the server or workstation as described in the server or workstation’s documentation (see figure 4). Figure 4 Removing the Workstation Cover (example) 4 Locate an available 5¼-inch drive bay and remove the front cover from the drive bay as described in the server or workstation’s documentation (see figure 5). 5 If necessary, install an LVD/SE host bus adapter in the server or workstation.
Chapter 2 Installing the Internal SCSI Tape Drive Installing the Internal SCSI Tape Drive 6 Slide the tape drive into the open drive bay (see figure 5).
Chapter 2 Installing the Internal SCSI Tape Drive Installing the Internal SCSI Tape Drive 7 Obtain a SCSI cable with an open 68-pin, high-density connector. Connect one end of the SCSI cable to the SCSI connector on the rear panel of the tape drive. The SCSI connectors are keyed, preventing improper connection (see figure 6). Note: If the SCSI cable does not fit the connector on the SCSI host adapter, you either have an incompatible SCSI host adapter or you need to purchase a cable adapter.
Chapter 2 Installing the Internal SCSI Tape Drive Installing the Internal SCSI Tape Drive 10 Secure the internal SCSI tape drive with the necessary mounting screws, either in the sides or bottom of the tape drive sled, as appropriate for the server or workstation chassis. See figure 7 for an example of where you might find these screws. Figure 7 Securing the Internal SCSI Tape Drive in the Installation Bay Note: Some servers and workstations require mounting rails for internal devices.
Chapter 2 Installing the Internal SCSI Tape Drive Confirming the Installation Confirming the Installation 2 When you turn on power to the tape drive, it performs its power-on selftest. The LEDs on the front panel of the tape drive illuminate in a specific sequence (see Power-On Self-Test (POST) Indicator Activity on page 51 for details).
Chapter 3 3 Installing the Internal SATA Tape Drive This chapter contains step-by-step instructions for installing the DLT-V4 internal SATA tape drive. The internal SATA tape drive attaches to the server through a SATA interface card. Equipment Required 3 All you need to install the DLT-V4 internal SATA tape drive is a PHILLIPS® screwdriver and adequate ESD protection. SATA Requirements 3 Use the internal SATA cable provided in your accessory kit.
Chapter 3 Installing the Internal SATA Tape Drive Installation Steps Installation Steps 3 To install the tape drive, perform the following tasks in this order. Follow the detailed instructions on the pages listed below. Table 3 Installing the DLT-V4 Internal SATA Tape Drive Step Instruction Page 1 Unpack and check the tape drive for shipping damage. Page 17 2 Select a server or workstation to host the tape drive.
Chapter 3 Installing the Internal SATA Tape Drive Installing the Internal SATA Tape Drive Installing the Internal SATA Tape Drive 3 To install the tape drive, follow these steps: 1 Shut down the operating system and power off the server or workstation. 2 Power off all peripheral devices, such as printers and other connected devices. Caution: Do not go to step 3 until you have completed steps 1 and 2. Failure to follow these instructions may result in damage to the tape drive or other devices.
Chapter 3 Installing the Internal SATA Tape Drive Installing the Internal SATA Tape Drive 4 Locate an available 5¼-inch drive bay and remove the front cover from the drive bay as described in the server or workstation’s documentation (see figure 9). 5 Slide the tape drive into the open drive bay (see figure 9).
Chapter 3 Installing the Internal SATA Tape Drive Installing the Internal SATA Tape Drive 6 Connect one end of the SATA data cable to the tape drive and the other end of the SATA data cable to the SATA host bus adapter (see figure 10). 7 Connect either the SATA power cable or drive power cable to the tape drive (see figure 10). Caution: Connect only one power cable to the drive; connecting both the SATA power cable and the drive power cable to the tape drive may damage the tape drive.
Chapter 3 Installing the Internal SATA Tape Drive Installing the Internal SATA Tape Drive 8 Secure the internal SATA tape drive with the supplied mounting screws in the installation bay, either on the sides or bottom of the tape drive sled, as appropriate for the server or workstation chassis. See figure 11 for an example of where you might find these screws.
Chapter 3 Installing the Internal SATA Tape Drive Confirming the Installation Confirming the Installation 3 When you turn on power to the tape drive, it performs its power-on selftest. The LEDs on the front panel of the tape drive illuminate in a specific sequence (see Power-On Self-Test (POST) Indicator Activity on page 51 for details).
Chapter 4 Installing the Internal SATA-to-USB Tape Drive 4 This chapter contains step-by-step instructions for installing the DLT-V4 internal SATA tape drive with USB adapter. The internal SATA-to-USB tape drive attaches to the server through a USB adapter. The SATA-to-USB tape drive is the same as the SATA tape drive but uses a special SATA-to-USB adapter to connect to the USB port on your PC’s motherboard or host bus adapter.
Chapter 4 Installing the Internal SATA-to-USB Tape Drive USB Requirements USB Requirements 4 The tape drive must be connected to a USB 2.0 port. Installation Steps 4 To install the tape drive, perform the following tasks in this order. Follow the detailed instructions on the pages listed below. Table 4 Installing the DLT-V4 Internal SATA-to-USB Tape Drive DLT-V4 Product Manual Step Instruction Page 1 Unpack and check the tape drive for shipping damage.
Chapter 4 Installing the Internal SATA-to-USB Tape Drive Unpacking the Internal SATA-to-USB Tape Drive Unpacking the Internal SATA-to-USB Tape Drive 4 Before you do anything else, unpack and inspect the tape drive for shipping damage. If you notice any damage, report it both to the sales representative and to the shipping company immediately. Note: Save the packing materials in case you need to move or ship the tape drive in the future.
Chapter 4 Installing the Internal SATA-to-USB Tape Drive Installing the Internal SATA-to-USB Tape Drive 3 Remove the cover from the server or workstation as described in the server or workstation’s documentation (see figure 12).
Chapter 4 Installing the Internal SATA-to-USB Tape Drive Installing the Internal SATA-to-USB Tape Drive 4 Locate an available 5¼-inch drive bay and remove the front cover from the drive bay as described in the server or workstation’s documentation (see figure 13). 5 Slide the tape drive into the open drive bay (see figure 13).
Chapter 4 Installing the Internal SATA-to-USB Tape Drive Connecting the SATA-to-USB Adapter 6 Connect either the SATA power cable or drive power cable to the tape drive (see figure 14). Caution: Connect only one power cable to the drive; connecting both the SATA power cable and the drive power cable to the tape drive may damage the tape drive. 7 Connect one end of the SATA data cable to the tape drive (see figure 14).
Chapter 4 Installing the Internal SATA-to-USB Tape Drive Connecting the SATA-to-USB Adapter 1 Connect the SATA cable to the SATA-to-USB adapter (see figure 15). 2 Connect the USB cable to the SATA-to-USB adapter (see figure 15). 3 Connect the USB cable to the host PC motherboard or the USB HBA (see figure 15 and figure 16). Note: Pin 1 location is marked on the cable connector with a triangle (T). Consult your motherboard/HBA manual for the Pin 1 location on the mating USB connector.
Chapter 4 Installing the Internal SATA-to-USB Tape Drive Completing the Internal SATA-to-USB Tape Drive Installation Figure 16 USB Connector Pin Locations and Signals Completing the Internal SATA-to-USB Tape Drive Installation 4 1 Secure the internal USB tape drive with the supplied mounting screws in the installation bay, either on the sides or bottom of the tape drive sled, as appropriate for the server or workstation chassis. See figure 17 for an example of where you might find these screws.
Chapter 4 Installing the Internal SATA-to-USB Tape Drive Completing the Internal SATA-to-USB Tape Drive Installation Figure 17 Securing the Internal SATA Tape Drive in the Installation Bay Note: Some servers and workstations require mounting rails for internal devices. Contact the server or workstation manufacturer for information. 2 Replace the cover on the server or workstation. 3 Connect the power cord to the server or workstation and any peripheral devices that you detached earlier.
Chapter 4 Installing the Internal SATA-to-USB Tape Drive Confirming the Installation Confirming the Installation 4 When you turn on power to the tape drive, it performs its power-on selftest. The LEDs on the front panel of the tape drive illuminate in a specific sequence (see Power-On Self-Test (POST) Indicator Activity on page 51 for details).
Chapter 5 5 Installing the Tabletop SCSI Tape Drive This section contains step-by-step instructions for installing the tabletop SCSI tape drive. Equipment Required 5 You need no special tools to install the DLT-V4 SCSI tabletop tape. You will need a ballpoint pen to change the SCSI ID switch on the rear panel of the tape drive.
Chapter 5 Installing the Tabletop SCSI Tape Drive Installation Steps of the SE bus (usually 40 MB/s). The DLT-V4 is not compatible with a highvoltage differential (HVD) SCSI bus. If you attach the tape drive to a narrow (50-pin) SCSI bus, you must use a customer-supplied 68-pin to 50-pin adapter that terminates the unused 18 pins. These adapters are sometimes labeled high-byte termination.
Chapter 5 Installing the Tabletop SCSI Tape Drive Unpacking the Tabletop SCSI Tape Drive Step Instruction Page 8 Complete installation by connecting the power cable to the tape drive, server or workstation, and all peripheral devices. Plug the power cable into the nearest power outlet and apply power to all devices. Page 42 9 Confirm the installation. Page 42 Unpacking the Tabletop SCSI Tape Drive 5 Before you begin, clear a desk or table so that you can unpack the tape drive.
Chapter 5 Installing the Tabletop SCSI Tape Drive Selecting a Location for the Tabletop SCSI Tape Drive Selecting a Location for the Tabletop SCSI Tape Drive 5 Select a location for the tape drive that is flat, sturdy, level, and close to the server or workstation. A desk or tabletop surface is most suitable. Regardless of the location you choose for the tape drive, make sure the environment is free from dust, cigarette smoke, and excessive temperature and humidity.
Chapter 5 Installing the Tabletop SCSI Tape Drive Setting the SCSI ID Setting the SCSI ID 5 All SCSI devices attached to the server or workstation must have a unique SCSI ID. Check the SCSI IDs on all other devices on the selected server or workstation, including the SCSI host adapter, and select an unused SCSI ID for the tape drive. The factory default SCSI ID for this tape drive is 5, as shown in figure 18.
Chapter 5 Installing the Tabletop SCSI Tape Drive Connecting the SCSI Interface Cables Figure 19 SCSI ID Selector Switch Press here to decrease SCSI ID Press here to increase SCSI ID Connecting the SCSI Interface Cables 5 In the final installation stage, you connect the SCSI and power cables to the tape drive. To connect the SCSI and power cables to the tape drive, follow these steps: 1 Shut down the operating system and power down the server or workstation.
Chapter 5 Installing the Tabletop SCSI Tape Drive Connecting the SCSI Interface Cables Figure 20 Tabletop Tape Drive SCSI and Power Cable Connections To next device To SCSI host adapter Power cords 5 Connect the other end of the SCSI cable to the connector on the SCSI host adapter or to the connector on the previous SCSI device on the SCSI bus, as shown in figure 21.
Chapter 5 Installing the Tabletop SCSI Tape Drive Terminating the SCSI Tabletop Tape Drive Figure 21 Server SCSI Cable Connections SCSI host adapter SCSI cable Terminating the SCSI Tabletop Tape Drive 5 You must terminate the tape drive if it is the last physical device on the SCSI bus (at the end of the SCSI chain). If another SCSI device is the last device on the SCSI bus, confirm that it is properly terminated and do not terminate the tape drive.
Chapter 5 Installing the Tabletop SCSI Tape Drive Terminating the SCSI Tabletop Tape Drive Powering the Terminator 5 At least one device on the SCSI bus must supply terminator power (TERMPWR). The factory default for the tape drive is for TERMPWR to be enabled. Only an authorized service provider can disable the tape drive TERMPWR setting. Attach the terminator as shown in figure 22. Note: It is acceptable for more than one device on the SCSI bus to provide TERMPWR.
Chapter 5 Installing the Tabletop SCSI Tape Drive Completing the Tabletop SCSI Tape Drive Installation Completing the Tabletop SCSI Tape Drive Installation 5 1 Secure the SCSI cable connectors by tightening the screws until snug. Note: If the SCSI cable does not fit the connector on the SCSI host adapter, you either have an incompatible SCSI host adapter or you need to purchase a cable adapter. Contact the sales representative or the SCSI host adapter manufacturer for information.
Chapter 6 Installing the Tabletop USB/eSATA Tape Drive 6 This chapter contains step-by-step instructions for installing the tabletop USB/eSATA tape drive. Equipment Required 6 You need no special tools to install the DLT-V4 USB/eSATA tabletop tape drive. USB Requirements 6 If you are using your tape drive in a USB configuration, for optimum performance, the tape drive should be connected to a USB 2.0 port and be the only device on the root hub.
Chapter 6 Installing the Tabletop USB/eSATA Tape Drive eSATA requirements eSATA requirements 6 If you are using the eSATA configuration, use the external eSATA cable provided in your accessories kit. Installation Steps 6 To install the tape drive, perform the following tasks in this order. Follow the detailed instructions on the pages listed below. Table 6 Installing the Tabletop SCSI Tape Drive DLT-V4 Product Manual Step Instruction Page 1 Unpack and check the tape drive for shipping damage.
Chapter 6 Installing the Tabletop USB/eSATA Tape Drive Unpacking the USB/eSATA Tabletop Tape Drive Unpacking the USB/eSATA Tabletop Tape Drive 6 Before you begin, clear a desk or table so that you can unpack the tape drive. You also need to select a location near the server or workstation that has room for the tape drive to sit without being crowded.
Chapter 6 Installing the Tabletop USB/eSATA Tape Drive Installing the Tabletop USB/eSATA Tape Drive Be sure to follow these additional guidelines when selecting a location for the tape drive: • Allow at least 6 inches (15.2 cm) behind the tape drive for proper cooling. • Avoid locations near printers or photocopy machines, both of which produce paper fiber and other types of dust and airborne contaminants. • Do not place the tape drive on the floor.
Chapter 6 Installing the Tabletop USB/eSATA Tape Drive Confirming the Installation Figure 23 Connecting the USB/eSATA Cables On Off eSATA cable USB cable Power cable Install EITHER (not both) 4 Connect the power cables to the host server or workstation and all peripheral devices. 5 Power on the tape drive and any attached peripheral devices. 6 Power on the server or workstation and allow its operating system to start.
Chapter 7 Installing the Device Drivers 7 This chapter describes how to install device drivers for Microsoft Microsoft Windows 2000, Windows XP, and Windows 2003 Server. Note: If you intend to use native operating system backup applications, you can find the required device drivers at www.quantum.com. Commercial backup applications generally provide all necessary device driver support.
Chapter 7 Installing the Device Drivers Microsoft Windows 2000 c In Device Manager, the DLT-V4 tape drive will be listed under either “Tape drives” or “Other devices”. Locate the entry for the DLT-V4 tape drive. Then double-click that entry to display the Drive Properties. d Click the Driver tab. Then click Update Driver .... e The “Hardware Update Wizard” will start. Proceed with step 3. 3 Select “Install from a list or specific location (Advanced)”. Then click Next.
Chapter 7 Installing the Device Drivers Microsoft Windows 2000 c In Device Manager, the DLT-V4 tape drive will be listed under either “Tape drives” or “Other devices”. Locate the entry for the DLT-V4 tape drive. Then double-click that entry to display the Drive Properties. d Click the Driver tab. Then click Update Driver .... e The “Upgrade Device Driver Wizard” will start. Proceed with step 4. 4 In the “Upgrade Device Driver Wizard”, click Next to continue.
Chapter 8 8 Using Your Tape Drive This chapter contains information regarding the functional operation of the DLT-V4 tape drive. LED Indicators 8 The tape drive has four light emitting diodes (LEDs). This section describes the functions of the LEDs. Note: Power-On Self-Test (POST) Indicator Activity 8 DLT-V4 Product Manual The front panel controls and indicators are in the same locations on both the internal and tabletop tape drives. The tabletop tape drive has a Power LED.
Chapter 8 Using Your Tape Drive LED Indicators approximately eight seconds. If a data cartridge is in the tape drive during POST, the Ready LED flashes until the tape drive executes a midtape load, which can take several minutes. As POST completes, the tape drive makes a faint buzzing noise for several seconds. The noise associated with this activity is normal for this technology and does not indicate a problem with the tape drive.
Chapter 8 Using Your Tape Drive LED Indicators Fault Clean Media – Description Calibration error or permanent write/ read error, cleaning suggested Cleaning required—250 tape motion hours exceeded since last cleaning – Cleaning in process User invoked write/read diagnostic failed Servo or mechanical error – – Internal firmware error Key – Off On Blinking–slow (approximately once per second) Blinking–medium (approximately twice per second) Blinking–fast (approximately three times per second) Indic
Chapter 8 Using Your Tape Drive Unload Button Functions Unload Button Functions 8 You can use the unload button to unload and eject data cartridges, and for the additional features shown in the following table. Press and hold the eject button for the time specified in the following table to activate one of these features. Release the button when the LEDs display the desired sequence. Caution: The two features noted in the following table will overwrite any data on the data cartridge.
Chapter 8 Using Your Tape Drive Unload Button Actions Ready (green) Description Fault (orange or clear) Clean (orange or clear) Media (orange or clear) Hold Time (seconds) Emergency reset 27 to 30 Revert back to normal mode – – – – 30+ Key – Off On (orange or green) Blinking Unchanged from previous condition Unload Button Actions 8 This section describes the unload button activity.
Chapter 8 Using Your Tape Drive Diagnostic Mode Event Codes Field/Mode Actions Read/write diagnostic start Caution: This feature overwrites any data currently on the data cartridge. Before performing this action, confirm that the data cartridge in the tape drive does not contain critical data. Release the unload button to start an internal read/ write diagnostic. You must then load a data cartridge to run the diagnostic. The tape drive writes and reads 3.6 GB of data, then unloads the data cartridge.
Chapter 8 Using Your Tape Drive Diagnostic Mode Event Codes character is either a hex E (error) or a B (bug check). You can look up the remaining seven characters in the error/bug check definition tables. When you display the last (eighth) detailed error code digit, the next button press returns the tape drive to normal operation. All indications are a four bit hex value. During any time in this procedure, the tape drive returns to normal operation if you perform no scroll action within 15 seconds.
Chapter 9 Using Data and Cleaning Cartridges 9 This chapter contains information about data and cleaning cartridges. Choosing Compatible Data Cartridges 9 Your Quantum DLT-V4 tape drive reads and writes DLTtape VS1 data cartridges unless they have been previously written with VS 160 format. Your DLT-V4 tape drive can read (but not write to) DLTtape IV data cartridges previously written with the DLT1/VS80 format and VS1 data cartridges previously written with the VS 160 format.
Chapter 9 Using Data and Cleaning Cartridges Loading a Data Cartridge Loading a Data Cartridge 9 After the tape drive completes POST, insert the DLTtape VS1 data cartridge into the cartridge slot, oriented as shown in figure 24 and push the data cartridge gently into the tape drive until it stops. Figure 24 Loading a DLTtape VS1 Data Cartridge The Ready LED blinks while the tape drive loads the data cartridge. When the data cartridge is ready to use, the tape drive illuminates the Ready LED.
Chapter 9 Using Data and Cleaning Cartridges Unloading a Data Cartridge Unloading a Data Cartridge 9 To unload a data cartridge from your tape drive, follow these steps: Caution: Remove the data cartridge from your tape drive before powering off the tape drive—or the server or workstation for an internal tape drive.
Chapter 9 Using Data and Cleaning Cartridges Write-Protecting the Data Cartridge Write-Protecting the Data Cartridge 9 All data cartridges have a write-protect switch to prevent accidental erasure of data. Before loading a data cartridge into your tape drive, make sure to position the write-protect switch on the front of the data cartridge as desired, as shown in figure 26. The indicator on the top of the data cartridge also points to the appropriate icon, indicating the write-protected status.
Chapter 9 Using Data and Cleaning Cartridges Caring for Your Data Cartridges Caring for Your Data Cartridges 9 To ensure the longest possible life for all of your DLTtape VS1 data cartridges, follow these guidelines: DLT-V4 Product Manual • Maintain clean and smoke-free operating and storage environments. • Do not drop or strike a data cartridge. Excessive shock can displace the tape leader, making the data cartridge unusable and possibly damaging your tape drive.
Chapter 9 Using Data and Cleaning Cartridges Using the Cleaning Cartridge Using the Cleaning Cartridge 9 When the Clean LED is illuminated, your tape drive’s read/write head needs to be cleaned. Caution: Follow the instructions as detailed in Loading a Data Cartridge on page 59 to load the cleaning cartridge. The DLT-V4 tape drive will accept only a DLT VS1 cleaning cartridge. Cleaning typically takes several minutes, during which the Clean LED blinks.
Chapter 10 10 Specifications This chapter contains the DLT-V4 tape drive specifications. Altitude 10 The tape drive operates normally in pressures from -500 feet to 30,000 feet.
Chapter 10 Specifications Dimensions and Weights Dimensions and Weights 10 Table 12 lists the physical dimensions of the tape drive. Table 12 Dimensions Specification Internal Tape Drive Tabletop Tape Drive Height 1.656 in. (42.05 mm) with the bezel 1.618 in. (41.10 mm) without the bezel 2.608 in. (66.24 mm) Width 5.748 in. (146.00 mm) behind the bezel 5.807 in. (147.50 mm) with the bezel 8.352 in. (212.13 mm) Length 8.614 in. (218.80 mm) measured from the rear of the front bezel 8.874 in.
Chapter 10 Specifications Temperature and Humidity Ranges Temperature and Humidity Ranges 10 Table 14 lists the operating temperature and humidity ranges of the tape drive. Table 14 Operating Temperature/Humidity Ranges Specification Value Temperature Range 10 ºC to 40 ºC (50 ºF to 104 ºF) Airflow 3.0 CFM (min.) Wet Bulb Temperature 25 ºC (77 ºF) Temperature Gradient 11 ºC (19.
Chapter 10 Specifications Functional Specifications Functional Specifications 10 Table 16 lists the DLT-V4 tape drive’s functional specifications.
Chapter 10 Specifications Timing Characteristics Timing Characteristics 10 Table 17 lists the timing characteristics of the DLT-V4 tape drive.
Chapter 10 Specifications Data Cartridge and Media Characteristics Data Cartridge and Media Characteristics 10 Table 18 lists the data cartridge and media characteristics. Table 18 Data Cartridge and Media Characteristics Characteristic Specification Media Width 0.5 in. Media Length 1,847 ft Media Type Metal Particle Data Cartridge Dimensions 4.1 in. x 4.1 in. x 1.0 in.
Chapter 11 Regulatory and Compliance Information 11 This chapter contains regulatory and compliance information for the DLT-V4 tape drive. Emissions 11 The tape drive meets the following standards: DLT-V4 Product Manual • FCC CFR Part 15 Class B (ANSI C63.
Chapter 11 Regulatory and Compliance Information Safety Requirements Safety Requirements 11 The tape drive meets the following standards: • Low Voltage Directive (73/23/EEC) • UL 60950 – US Standard: Safety of Information Technology Equipment including Electrical Business Equipment • CSA C22.
Chapter 11 Regulatory and Compliance Information Statements for Class A Equipment (Internal Tape Drive) • Part 2 - Electrostatic Discharge (ESD) Requirements • Part 3 - Radiated Electromagnetic Field Requirements • Part 4 - Electrical Fast Transient/Burst (EFT) Requirements • Part 5 - Surge Requirements • Part 6 - Conducted disturbances, induced by radio-frequency fields Requirements • Part 8 - Power frequency magnetic field Requirements • Part 11 – Voltage dips, short interruptions and voltag
Chapter 11 Regulatory and Compliance Information Statements for Class A Equipment (Internal Tape Drive) accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Chapter 11 Regulatory and Compliance Information Statements for Class A Equipment (Internal Tape Drive) VCCI Notice (Japan) 11 DEN-AN Notice (Japan) 11 Class B ITE Translation 11 This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this product is used near a radio or television receiver in a domestic environment, it may cause radio interference.
Chapter 11 Regulatory and Compliance Information Environmental Compliance Environmental Compliance 11 Quantum is committed to providing quality products in an environmentally sound manner and to comply with all applicable environmental laws, rules and regulations.
Glossary A (v.) To read, write, or update information on a storage medium, such as magnetic media. (n.) The operation of reading, writing, or updating stored information. Access Access Time The interval between the time a request for data is made by the system and the time the data is available from the tape drive. Archiving The removal or copying of data from the computer system onto secondary storage media that is safely stored away.
Glossary C C The degree Celsius (°C) is a unit of temperature. Cartridge Receiver At media insertion, the cartridge receiver assembly is responsible for guiding the media into its operating position, opening the door, unlocking the cartridge brakes, and securing the media for operation. At media ejection, the cartridge receiver assembly reverses the process and automatically ejects the cartridge a fixed distance from the front of the tape drive. CE Council of Europe.
Glossary EMC Electromagnetic Compatibility. EMI Electromagnetic Interference. EN EN standards are voluntary technical standards of the European Union and European Economic Area. EOD End of Data. Location on media where the last session stopped. EOM or EOT End of Media or End of Tape. Logical EOM allows space to complete a write operation; physical EOM signifies that the media is completely used. Erase The removal of data from media.
Glossary H Head The tiny electromagnetic coil and metal pole used to create and read back the magnetic patterns on the media. Also known as the read/write head. I IEC The International Electrotechnical Commission is a standards organization that prepares and publishes international standards for all electrical, electronic, and related technologies.
Glossary MSE Multi-mode Single-Ended is a signaling alternative for multi-mode SCSI devices that allows multi-mode SCSI devices to operate while SE SCSI devices are present on the bus. MTBF Mean Time Between Failures. N Native Capacity The capacity of a given media product in its basic recording format (without the use of data compression). Native Mode Refers to the uncompressed storage capacity of a media subsystem. (See Native Capacity.
Glossary The length of time that media can be stored without losing its magnetic strength. For VS1 media, this period is 30 years or more. Shelf Life SI The International System of Units. T A physical requirement of the SCSI bus. A terminator is a device that attaches to both ends of an electrical bus and prevents reflection or echoes of signals that reach the end of the bus. Termination Track A linear or angled pattern of data written on a media surface.
