User guide
Table Of Contents
- 1 Safety Information
- 2 Product Information
- 3 Mechanical Installation
- 4 Electrical Installation
- 4.1 Electrical connections/ Power connections
- 4.2 Ground connections
- 4.3 AC supply requirements
- 4.4 Line reactors
- 4.5 Auxiliary AC supply and connections
- 4.6 Separating the Auxiliary Supply
- 4.7 Control 120 Vac supply
- 4.8 Control 24 Vdc supply
- 4.9 Cable and fuse size ratings
- 4.10 External suppressor resistor
- 4.11 Ground leakage
- 4.12 EMC (Electromagnetic compatibility)
- 4.13 Serial communications connections
- 4.14 Shield connections
- 4.15 Control connections
- 4.16 General
- 4.17 Connecting an encoder
- 5 Getting Started
- 5.1 Understanding the display
- 5.2 Keypad operation
- 5.3 Menu 0 (sub block)
- 5.4 Pre-defined sub blocks
- 5.5 Menu 0 (linear)
- 5.6 Menu structure
- 5.7 Advanced menus
- 5.8 Saving parameters
- 5.9 Restoring parameter defaults
- 5.10 Displaying parameters with non- default values only
- 5.11 Displaying destination parameters only
- 5.12 Parameter access level and security
- 5.13 Serial communications
- 6 Basic parameters
- 7 Running the Motor
- 8 Optimization
- 9 SMARTCARD Operation
- 9.1 Introduction
- 9.2 Easy saving and reading
- 9.3 Transferring data
- 9.3.1 Writing to the SMARTCARD
- 9.3.2 Reading from the SMARTCARD
- 9.3.3 Auto saving parameter changes
- 9.3.4 Booting up from the SMARTCARD on every power up (Pr 11.42 (SE09, 0.30) = boot (4))
- 9.3.5 Booting up from the SMARTCARD on every power up (Pr xx.00 = 2001)
- 9.3.6 Comparing drive full parameter set with the SMARTCARD values
- 9.3.7 7yyy / 9999 - Erasing data from the SMARTCARD
- 9.3.8 9666 / 9555 - Set / clear SMARTCARD warning suppression flag
- 9.3.9 9888 / 9777 - Set / clear the SMARTCARD read only flag
- 9.4 Data block header information
- 9.5 SMARTCARD parameters
- 9.6 SMARTCARD trips
- 10 Onboard PLC
- 11 Advanced Parameters
- 11.1 Menu 1: Speed reference
- 11.2 Menu 2: Ramps
- 11.3 Menu 3: Speed feedback and speed control
- 11.4 Menu 4: Torque and current control
- 11.5 Menu 5: Motor and field control
- 11.6 Menu 6: Sequencer and clock
- 11.7 Menu 7: Analog I/O
- 11.8 Menu 8: Digital I/O
- 11.9 Menu 9: Programmable logic, motorized pot and binary sum
- 11.10 Menu 10: Status and trips
- 11.11 Menu 11: General drive set-up
- 11.12 Menu 12: Threshold detectors, variable selectors and brake control function
- 11.13 Menu 13: Position control
- 11.14 Menu 14: User PID controller
- 11.15 Menus 15, 16 and 17: Solutions Module slots
- 11.16 SM-I/O120V Solutions Module parameter settings
- 11.17 Menu 18: Application menu 1
- 11.18 Menu 19: Application menu 2
- 11.19 Menu 20: Application menu 3
- 11.20 Menu 21: Second motor parameters
- 11.21 Menu 22: Additional Menu 0 set-up
- 11.22 Menu 23: Header selections
- 11.23 Advanced features
- 12 Technical Data
- 12.1 Drive technical data
- 12.1.1 Power and current ratings
- 12.1.2 Power dissipation
- 12.1.3 AC Supply requirements
- 12.1.4 Supply types
- 12.1.5 SCR bridge AC Supply
- 12.1.6 Auxiliary AC supply
- 12.1.7 Line reactors
- 12.1.8 Temperature, humidity and cooling method
- 12.1.9 Storage
- 12.1.10 Altitude
- 12.1.11 IP Rating
- 12.1.12 Corrosive gasses
- 12.1.13 RoHS compliance
- 12.1.14 Vibration
- 12.1.15 Start up time
- 12.1.16 Output speed range
- 12.1.17 Accuracy
- 12.1.18 Acoustic noise
- 12.1.19 Overall dimensions
- 12.1.20 Weights
- 12.2 Cable and fuse size ratings
- 12.3 Optional external EMC filters
- 12.1 Drive technical data
- 13 Diagnostics
- 14 UL Information
- List of tables
- Index
Safety
Information
Product
Information
Mechanical
Installation
Electrical
Installation
Getting
Started
Basic
parameters
Running the
Motor
Optimization
SMARTCARD
Operation
Onboard
PLC
Advanced
Parameters
Technical
Data
Diagnostics
UL
Information
Quantum MP User Guide 29
Issue: A3 www.emersonct.com
X1 X2 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9
Q10
Q11 Q12
1234567891011
12
MP10 User Interface Board
SM-IO-120V Solutions Module
in Mentor MP Slot 3
N/C
N/C
E1 E3
L1 L2
F- F+ A2 MA2
L3
L12 L11 MA1
A1
PE
C1 C2 C3 C4 C5 C6 C7 C8 C9
C10
C11 C12 C13 C14 C15 C16
TB4
TB3TB2TB1
E-Stop
Stop
Interlocks
Run
Jog
Fwd
Reset
Drive
Tac h
Rev
Motor
Thermal
Enable
Speed Pot
Motor
Thermistor
(Optional)
PR
7.15
41 42 22 31 8 11 3 6 5 4
[A1] [MA1] [MA2]
[A2]
TAB 1
TAB 2
+24
Drive Enable
Analog Input 3
0 V
0 V
Analog Input 1 Inverting Input
Analog Input 1 Non-Inverting Input
+10 V, 10 mA
-
+
A2A1
DB+DB-
SR2SR1
F2
MC
- BC +
F4
F3
F2
F1
F4
F3
F1
F2
F8F6F4
L1 L2 L3
External
Suppression
Resistor
M
1
A1 [A2]
7
A2 [A1]
Motor Armature
Dynamic Brake
Resistor
Input Voltage
208/240/380/416/480 VAC
50/60 Hz
Semiconductor
(Line) Fuses
1
Mentor MP Size 1
DC
Protection
(Armature)
Fuse
Motor Field
4
300 VDC
Connection
150 VDC
Connection
CAUTION: Verify Control
Transformer is configured per
Table 1 before applying input
voltage!
3
Contactor Control 2-way plug
located near drive PE terminal
PL11 on Mentor MP90 PCB
9
5
TABLE 2 - QUANTUM MP FUSES
MODEL
LINE FUSES F4, F6, F8 - 500V
ARMATURE FUSE F2 - 700V (SEE NOTE )
CT P/N MFG P/N RATING CT P/N MFG P/N RATING
QMP45A4
3701-500090
FWH-90B 90A
3701-700090
FWP-90B 90A
QMP45A4R A50QS70-4
70A
A70QS80-4
80A
QMP75A4
3701-500125
FWH-150B 150A
3701-700125
FWP-125A 125A
QMP75A4R AQ50QS125-4
125A
A70QS125-4
125A
QMP155A4
3701-500250
FWH-250A 250A
3701-700250
FWP-250A 250A
QMP155A4R A50QS250-4
250A
A70QS250-4
250A
QMP210A4
3701-500350
FWH-350A 350A
3701-700350
FWP-350A 350A
QMP210A4R A50QS350-4
350A
A70QS350-4
350A
NOTE: ARMATURE FUSE IS ONLY USED ON "R" MODEL FOUR QUADRANT DRIVES
1
on MP14
PCB
on MP14
PCB
ON