User guide
Table Of Contents
- 1 Safety Information
- 2 Product Information
- 3 Mechanical Installation
- 4 Electrical Installation
- 4.1 Electrical connections/ Power connections
- 4.2 Ground connections
- 4.3 AC supply requirements
- 4.4 Line reactors
- 4.5 Auxiliary AC supply and connections
- 4.6 Separating the Auxiliary Supply
- 4.7 Control 120 Vac supply
- 4.8 Control 24 Vdc supply
- 4.9 Cable and fuse size ratings
- 4.10 External suppressor resistor
- 4.11 Ground leakage
- 4.12 EMC (Electromagnetic compatibility)
- 4.13 Serial communications connections
- 4.14 Shield connections
- 4.15 Control connections
- 4.16 General
- 4.17 Connecting an encoder
- 5 Getting Started
- 5.1 Understanding the display
- 5.2 Keypad operation
- 5.3 Menu 0 (sub block)
- 5.4 Pre-defined sub blocks
- 5.5 Menu 0 (linear)
- 5.6 Menu structure
- 5.7 Advanced menus
- 5.8 Saving parameters
- 5.9 Restoring parameter defaults
- 5.10 Displaying parameters with non- default values only
- 5.11 Displaying destination parameters only
- 5.12 Parameter access level and security
- 5.13 Serial communications
- 6 Basic parameters
- 7 Running the Motor
- 8 Optimization
- 9 SMARTCARD Operation
- 9.1 Introduction
- 9.2 Easy saving and reading
- 9.3 Transferring data
- 9.3.1 Writing to the SMARTCARD
- 9.3.2 Reading from the SMARTCARD
- 9.3.3 Auto saving parameter changes
- 9.3.4 Booting up from the SMARTCARD on every power up (Pr 11.42 (SE09, 0.30) = boot (4))
- 9.3.5 Booting up from the SMARTCARD on every power up (Pr xx.00 = 2001)
- 9.3.6 Comparing drive full parameter set with the SMARTCARD values
- 9.3.7 7yyy / 9999 - Erasing data from the SMARTCARD
- 9.3.8 9666 / 9555 - Set / clear SMARTCARD warning suppression flag
- 9.3.9 9888 / 9777 - Set / clear the SMARTCARD read only flag
- 9.4 Data block header information
- 9.5 SMARTCARD parameters
- 9.6 SMARTCARD trips
- 10 Onboard PLC
- 11 Advanced Parameters
- 11.1 Menu 1: Speed reference
- 11.2 Menu 2: Ramps
- 11.3 Menu 3: Speed feedback and speed control
- 11.4 Menu 4: Torque and current control
- 11.5 Menu 5: Motor and field control
- 11.6 Menu 6: Sequencer and clock
- 11.7 Menu 7: Analog I/O
- 11.8 Menu 8: Digital I/O
- 11.9 Menu 9: Programmable logic, motorized pot and binary sum
- 11.10 Menu 10: Status and trips
- 11.11 Menu 11: General drive set-up
- 11.12 Menu 12: Threshold detectors, variable selectors and brake control function
- 11.13 Menu 13: Position control
- 11.14 Menu 14: User PID controller
- 11.15 Menus 15, 16 and 17: Solutions Module slots
- 11.16 SM-I/O120V Solutions Module parameter settings
- 11.17 Menu 18: Application menu 1
- 11.18 Menu 19: Application menu 2
- 11.19 Menu 20: Application menu 3
- 11.20 Menu 21: Second motor parameters
- 11.21 Menu 22: Additional Menu 0 set-up
- 11.22 Menu 23: Header selections
- 11.23 Advanced features
- 12 Technical Data
- 12.1 Drive technical data
- 12.1.1 Power and current ratings
- 12.1.2 Power dissipation
- 12.1.3 AC Supply requirements
- 12.1.4 Supply types
- 12.1.5 SCR bridge AC Supply
- 12.1.6 Auxiliary AC supply
- 12.1.7 Line reactors
- 12.1.8 Temperature, humidity and cooling method
- 12.1.9 Storage
- 12.1.10 Altitude
- 12.1.11 IP Rating
- 12.1.12 Corrosive gasses
- 12.1.13 RoHS compliance
- 12.1.14 Vibration
- 12.1.15 Start up time
- 12.1.16 Output speed range
- 12.1.17 Accuracy
- 12.1.18 Acoustic noise
- 12.1.19 Overall dimensions
- 12.1.20 Weights
- 12.2 Cable and fuse size ratings
- 12.3 Optional external EMC filters
- 12.1 Drive technical data
- 13 Diagnostics
- 14 UL Information
- List of tables
- Index
Safety
Information
Product
Information
Mechanical
Installation
Electrical
Installation
Getting
Started
Basic
parameters
Running the
Motor
Optimization
SMARTCARD
Operation
Onboard
PLC
Advanced
Parameters
Technical
Data
Diagnostics
UL
Information
Quantum MP User Guide 139
Issue: A3 www.emersonct.com
Figure 11-21 Relay logic diagram
0.XX
0.XX
Key
Read-write (RW)
parameter
Read-only (RO)
parameter
Input
terminals
Output
terminals
12
12
11
11
Relay 2
0V
C16
C16
X1
X1
Q12
Q12
Q11
Q11
??.??
??.??
Relay 2
source
Any bit or
integer
parameter
Contactor
enable
17.28
Relay 2
invert
17.18
0
1
x(-1)
17.08
Relay 2
state
6.55
10
10
11
11
Relay 1
0V
??.??
??.??
Relay 1
source
Any bit or
integer
parameter
17.27
Relay 1
invert
17.17
0
1
x(-1)
17.07
Relay 1
state
The parameters are all shown at their default settings
MP 10
User Interface Board
SM-I/O120V in Slot 3
Parameter
Range(
) Default()
Type
17.01 Solutions Module ID 0 to 599 206 RO Uni PT US
17.02 Solutions Module software version 0.00 to 99.99
RO Uni NC PT
17.03 T4 digital input 3 state OFF (0) or ON (1)
RO Bit NC PT
17.04 T5 digital input 4 state OFF (0) or On (1)
RO Bit NC PT
17.05 T7 digital input 5 state OFF (0) or On (1)
RO Bit NC PT
17.06 T8 digital input 6 state OFF (0) or On (1)
RO Bit NC PT
17.07 Relay 1 state OFF (0) or On (1)
RO Bit NC PT
17.08 Relay 2 state OFF (0) or ON (1)
RO Bit NC PT
17.09 T1 digital input 1 state OFF (0) or ON (1)
RO Bit NC PT
17.10 T2 digital input 2 state OFF (0) or ON (1)
RO Bit NC PT
17.11 T1 digital input 1 invert OFF (0) or ON (1) OFF (0) RW Bit US
17.12 T2 digital input 2 invert OFF (0) or ON (1) OFF (0) RW Bit US
17.13 T4 digital input 3 invert OFF (0) or ON (1) OFF (0) RW Bit US
17.14 T5 digital input 4 invert OFF (0) or ON (1) OFF (0) RW Bit US
17.15 T7 digital input 5 invert OFF (0) or ON (1) OFF (0) RW Bit US
17.16 T8 digital input 6 invert OFF (0) or ON (1) OFF (0) RW Bit US
17.17 Relay 1 invert OFF (0) or ON (1) OFF (0) RW Bit US
17.18 Relay 2 invert OFF (0) or ON (1) OFF (0) RW Bit US
17.20 Digital I/O read word 0 to 255
RO Uni NC PT
17.21 T1 digital input 1 destination PR 0.00 to PR 21.51 PR 6.39 RW Uni DE US
17.22 T2 digital input 2 destination PR 0.00 to PR 21.51 PR 6.34 RW Uni DE US
17.23 T4 digital input 3 destination PR 0.00 to PR 21.51 PR 6.31 RW Uni DE US
17.24 T5 digital input 4 destination PR 0.00 to PR 21.51 PR 6.33 RW Uni DE US
17.25 T7 digital input 5 destination PR 0.00 to PR 21.51 PR 10.33 RW Uni DE US
17.26 T8 digital input 6 destination PR 0.00 to PR 21.51 PR 0.00 RW Uni DE US
17.27 Relay 1 source PR 0.00 to PR 21.51 PR 0.00 RW Uni US