QBOX-1010 0.
Contact Info: Quanmax Inc. 5F, No. 415, Ti-Ding Blvd. Sec. 2, NeiHu District, Taipei, Taiwan 114 Tel: +886-2-2799-2789 Fax: +886-2-2799-7399 Visit our site at: www.quanmax.com © 2009 Quanmax Inc. All rights reserved. The information in this user’s guide is provided for reference only. Quanmax does not assume any liability arising out of the application or use of the information or products described herein.
Content Content Content ................................................................................................................................... 3 Figures .................................................................................................................................... 4 Tables...................................................................................................................................... 4 Safety Instructions ...............................................
Tables Figures Figure 1 Front Panel .................................................................................. 15 Figure 2 Rear Panel................................................................................... 17 Figure 3 Mechanical Dimensions ............................................................... 19 Figure 4 Connect the DVI cable ................................................................. 20 Figure 5 Connecting USB mouse & keyboard............................................
Safety Instructions Safety Instructions Before You Begin Before handling the product, read the instructions and safety guidelines on the following pages to prevent damage to the product and to ensure your own personal safety. Refer to the “Advisories” section in the Preface for advisory conventions used in this user’s guide, including the distinction between Warnings, Cautions, Important Notes, and Notes. Always use caution when handling/operating a computer.
Safety Instructions When Working Inside a Computer Before taking covers off a computer, perform the following steps: 1. Turn off the computer and any peripherals. 2. Disconnect the computer and peripherals from their power sources or subsystems to prevent electric shock or system board damage. This does not apply when hot swapping parts. 3. Follow the guidelines provided in “Preventing Electrostatic Discharge” on the following page. 4.
Safety Instructions the component in a computer. Just before unwrapping the antistatic packaging, be sure you are at an ESD workstation or grounded. This will discharge any static electricity that may have built up in your body. When transporting a sensitive component, first place it in an antistatic container or packaging. Handle all sensitive components at an ESD workstation. If possible, use antistatic floor pads and workbench pads. Handle components and boards with care.
Preface Preface How to Use This Guide This guide is designed to be used as step-by-step instructions for installation, and as a reference for operation, troubleshooting, and upgrades. NOTE Driver downloads and additional information are available under Downloads on our web site: www.quanmax.com. Unpacking When unpacking, follow these steps: 1. After opening the box, save it and the packing material for possible future shipment. 2. Remove all items from the box.
Preface interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Preface account, send an email to support@quanmax.com to apply for one. All product(s) returned to Quanmax for service or credit must be accompanied by a Return Material Authorization (RMA) Number. Freight on all returned items must be prepaid by the customer who is responsible for any loss or damage caused by common carrier in transit. Returns for Warranty must include a Failure Report for each unit, by serial number(s), as well as a copy of the original invoice showing the date of purchase.
Preface turning it on. Failure to do so may cause damage to internal components, particularly the hard disk drive. Humidity High-humidity can cause moisture to enter and accumulate in the system. This moisture can cause corrosion of internal components and degrade such properties as electrical resistance and thermal conductivity. Extreme moisture buildup inside the system can result in electrical shorts, which can cause serious damage to the system.
Preface Line conditioners keep a system’s AC power source voltage at a fairly constant level and, therefore, can handle brownouts. Because of this added protection, line conditioners cost more than surge protectors. However, line conditioners cannot protect against a complete loss of power. Uninterruptible Power Supply Uninterruptible power supply (UPS) systems offer the most complete protection against variations on power because they use battery power to keep the server running when AC power is lost.
Chapter 1 Chapter 1 Introduction Overview The QBOX-1010 is a fan-less Box PC with a volume of just 0.6-liter that is ideal for space critical applications. This embedded hardware platform is designed with Intel® Atom N270 Processor which provides with excellent performance enabled by nextgeneration 45nm Process Technology. The system is supported with Intel® 945GSE /ICH7-M chipset, and DDR2 SO-DIMM up to 2GB. Featured are an eSATA, 1x 2.5” SATA HDD or 1x Internal Compact Flash Type II slot, GbE, USB 2.
Chapter 1 Product Specifications QBOX-1010 Construction Aluminum extrusion System Board Proprietary motherboard, Intel® Atom N270 Processor , 945GSE / ICH7-M Memory DDR2 533 SO-DIMM up to 2GB Front I/O panel 1x Phone Jack for Line-Out 1x Phone Jack for MIC-In 1x Push button for power on/off 1x Push button for reset 1x POWER LED 1x HDD LED 2x USB2.0 1x eSATA connector I/O Panel Rear I/O panel 1x DC JACK for DC9V ~ DC24V input 1x DVI-I connector for CRT & DVI output 2x USB2.
Chapter 1 System tour Refer to the diagrams below to identify the components of the system. Front Panel Figure 1 Front Panel eSATA The eSATA connector provides an external connectivity for mass storage devices. CAUTION This connector do not support hot-swapping. Users should not connect or disconnect their eSATA devices from PC when the system is working. USB The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mouse devices, cameras, and hard disk drives.
Chapter 1 MIC-IN The microphone jack is designed to connect the microphone used for video conferencing, voice narrations, or simple audio recordings. Audio Out The stereo headphone jack (3.5mm) is used to connect the system’s audio out signal to amplified speakers or headphones. Power LED The power LED will light when the PC is power-on. HDD LED The hard disk LED blinks when data is being written into or read from the HDD.
Chapter 1 Rear Panel Figure 2 Rear Panel USB The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mouse devices, cameras, and hard disk drives. USB allows many devices to run simultaneously on a single computer, with some peripheral acting as additional plug-in sites or hubs. DVI Port The Digital Visual Interface (DVI-I) port supports a high quality VGA-compatible device such as a monitor or LCD TV to allow viewing on a larger external display.
Chapter 1 COM1/COM2 Those two DB-9 male connectors support RS-232/422/485, 5V & 12V selected by BIOS setting, and output current 1A.
Chapter 1 Mechanical Dimensions Dimensions in millimeters Figure 3 Mechanical Dimensions QBOX-1010 User’s Manual 19
Chapter 2 Chapter 2 Getting Started Setting up your PC Connect the monitor, mouse and keyboard Connecting the monitor Connect the DVI cable from your display to the DVI port. Figure 4 Connect the DVI cable NOTE To connect a VGA display, you need the DVI to VGA adapter to connect a display with a VGA connector. NOTE When the system reboots without connecting the DVI, there might be no image on screen when you insert the DVI cable.
Chapter 2 Connecting USB mouse & keyboard Your QBOX-1010 does not come with a keyboard and mouse, but you can use any USB keyboard or mouse with your computer. Figure 5 Connecting USB mouse & keyboard NOTE Using a third-party USB mouse or keyboard may require software drivers. Check the manufacturer’s website for the latest software drivers. Connecting to a network device Connect one end of a network cable to the LAN port on the system rear panel and the other end to a hub or switch.
Chapter 2 Figure 7 Turing on the system Mounting your PC to a monitor 1. Secure the VESA mounting kit (optional accessory) to your monitor with four screws. Figure 8 VESA mounting (1) NOTE To fasten the metal shelf, your monitor must comply with VESA75 or VESA100 standard. 2. Place the QBOX-1010 on the VESA mounting kit and make sure the computer is fitting well on the bracket.
Chapter 2 VESA Mounting Kit Dimension Install your DIN-Rail Mounting Kit 1. Secure the DIN-Rail mounting kit “A” (optional accessory) to your system with 3x M3x6 round head screws. 2. Secure the DIN-Rail mounting kit “B” (optional accessory) to DIN-Rail mounting kit “A” with 3x M3X4 flat head screws.
Chapter 2 3. Clip the system onto the DIN rail as shown below.
Chapter 3 Chapter 3 AMI BIOS Setup Overview This chapter provides a description of the AMI BIOS. The BIOS setup menus and available selections may vary from those of your product. For specific information on the BIOS for your product, please contact Quanmax. NOTE: The BIOS menus and selections for your product may vary from those in this chapter.
Chapter 3 Main Menu The BIOS Setup is accessed by pressing the DEL key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. Once you enter the BIOS Setup Utility, the Main Menu will appear on the screen. The Main Menu provides System Overview information and allows you to set the System Time and Date. Use the “<” and “>” cursor keys to navigate between menu screens.
Chapter 3 not previously formatted with LBA mode disabled. Options: Disabled, Auto DMA Mode [Auto] Options: Auto S.M.A.R.T [Auto] SMART stands for Smart Monitoring, Analysis, and Reporting Technology. It allows AMIBIOS to use the SMART protocol to report server system information over a network. Options: Auto, Disabled, Enabled Table 4 System Information BIOS SETUP UTILITY Main Advanced BIOS Version Build Date: Boot Chipset Power Security Exit : 0.03 :06/25/09 Processor Intel® ATOM™ CPU N270 @ 1.
Chapter 3 Table 6 OnBoard I/O Configuration Settings BIOS SETUP UTILITY Main Advanced Boot Chipset Power Exit Allows BIOS to Select Serial Port1 Base Address. OnBoard I/O Configuration COM1 Address COM1 Function Type COM1 RI PIN Voltage COM2 Address COM2 Function Type COM2 RI Pin Voltage Security [3F8/IRQ4] [RS232] [Normal] [2F8/IRQ3] [RS232] [Normal] <> Select Screen ↑↓ Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02.
Chapter 3 Audio Controller [Enabled] Options: Enabled, Disabled Onboard LAN Controller [Enabled] Options: Enabled, Disabled Onboard LAN OPTROM [Disabled] Options: Enabled, Disabled Table 8 Hardware Health Configuration BIOS SETUP UTILITY Main Advanced Boot Chipset Power Security Exit Disabled Hardware Health Configuration CPU Shutdown Temperature [Disabled] 80°C/176°F CPU Temperature :43°C/ 109°F 85°C/185°F Fan Speed :366 RPM 90°C/194°F 95°C/203°F +VCORE :1.
Chapter 3 Boot Device Priority The items allow you to specify the Boot Device Priority sequence. Hard Disk Drives The items allow you to specify the Boot Device Priority sequence from available Removable Drives. Full Screen LOGO Display [Disabled] Options: Disabled, Enabled Quick Boot [Enabled] Enabling this item allows BIOS to skip some Power On Self Tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items.
Chapter 3 DRAM Frequency [Auto] Options: Auto, 400 MHz, 533MHz Internal Graphics Mode Select [Enabled 8MB] Select the amount of system memory used by the Internal graphics device.
Chapter 3 Options: Disabled, Enabled Resume On RTC Alarm [Disabled] Options: Disabled, Enabled Security Menu Table 12 Security Menu BIOS SETUP UTILITY Main Advanced Boot Chipset Power Security Exit Install or Change the password. Security Setting Supervisor Password :Not Installed User Password :Not Installed <> Select Screen ↑↓ Select Item +- Change Field Change Supervisor Password Tab Select Field Change User Password F1 General Help F10 Save and Exit ESC Exit V02.
Chapter 3 Save Changes and Exit Exit system setup after saving the changes. Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select [Yes] to save changes and exit. Discard Changes and Exit Exit system setup without saving any changes.
Chapter 4 Chapter 4 Driver Installation If your QBOX-1010 does not come with an operating system pre-installed, you will need to install an operating system and the necessary drivers to operate it. After you have finished assembling your system and connected the appropriate power source, power it up using the power supply and install the desired operating system. You can download the drivers for the QBOX-1010 from the Quanmax website at www.quanmax.com and install as instructed there.
Appendix A Appendix A DIO (Digital I/O) Sample Code //============================================ //QBOX-1010 DOS DIO sample program //Please compile with Turbo C 3.
Appendix B Appendix B WatchDog Timer Sample Code //============================================ //QBOX-1010 DOS watchdog sample program //Please compile with Turbo C 3.