KPC-1530/1730 Fanless Industrial Panel PC with Intel® Atom N270 + Intel® 945GSE/ ICH7-M User’s Guide KPC-1530/ 1730 User’s Manual I
Contact Info: Quanmax Inc. 5F, No. 415, Ti-Ding Blvd. Sec. 2, NeiHu District, Taipei, Taiwan 114 Tel: +886-2-2799-2789 Fax: +886-2-2799-7399 Visit our site at: www.quanmax.com © 2009 Quanmax Inc. All rights reserved. The information in this user’s guide is provided for reference only. Quanmax does not assume any liability arising out of the application or use of the information or products described herein.
Content Content Content....................................................................................................................... 3 Figures ....................................................................................................................... 4 Tables ......................................................................................................................... 5 Safety Instructions .....................................................................................
Figures Figures Figure 1 Mechanical Layout - Front and Side ............................................ 15 Figure 2 Mechanical Layout - I/O Panel ..................................................... 15 Figure 3 Mechanical Dimensions (KPC-1530) ........................................... 16 Figure 4 Mechanical Dimensions (KPC-1730) ........................................... 17 Figure 5 Removing the rear cover..............................................................
Tables Tables Table 1 Specifications ................................................................................ 14 Table 2 AUDIO, 3-Port Audio phone jack ................................................... 30 Table 3 USB, USB2.0 Type A Connector.................................................... 30 Table 4 LAN, Ethernet RJ-45 Connector .................................................... 30 Table 5 COM1 RS-232/422/485 Connector (DB9) .....................................
Safety Instructions Safety Instructions Before You Begin Before handling the product, read the instructions and safety guidelines on the following pages to prevent damage to the product and to ensure your own personal safety. Refer to the “Advisories” section in the Preface for advisory conventions used in this user’s guide, including the distinction between Warnings, Cautions, Important Notes, and Notes. Always use caution when handling/operating a computer.
Safety Instructions To help avoid possible damage to system boards, wait five seconds after turning off the computer before removing a component, removing a system board, or disconnecting a peripheral device from the computer. When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with locking tabs. If you are disconnecting this type of cable, press in on the locking tabs before disconnecting the cable.
Preface Preface How to Use This Guide This guide is designed to be used as step-by-step instructions for installation, and as a reference for operation, troubleshooting, and upgrades. NOTE Driver downloads and additional information are available under Downloads on our web site: www.quanmax.com. Unpacking When unpacking, follow these steps: 1. 2. 3. After opening the box, save it and the packing material for possible future shipment. Remove all items from the box.
Preface interference to radio communications. Operation of this equipment in a residential area (domestic environment) is likely to cause harmful interference, in which case the user will be required to correct the interference (take adequate measures) at their own expense. Changes or modifications not expressly approved by Quanmax could void the user's authority to operate the equipment.
Preface common carrier in transit. Returns for Warranty must include a Failure Report for each unit, by serial number(s), as well as a copy of the original invoice showing the date of purchase. To reduce risk of damage, returns of product must be in a Quanmax shipping container. If the original container has been lost or damaged, new shipping containers may be obtained from Quanmax Customer Service at a nominal cost. Quanmax owns all parts removed from repaired products.
Preface High-humidity can cause moisture to enter and accumulate in the system. This moisture can cause corrosion of internal components and degrade such properties as electrical resistance and thermal conductivity. Extreme moisture buildup inside the system can result in electrical shorts, which can cause serious damage to the system. Buildings in which climate is controlled usually maintain an acceptable level of humidity for system equipment.
Preface Uninterruptible Power Supply Uninterruptible power supply (UPS) systems offer the most complete protection against variations on power because they use battery power to keep the server running when AC power is lost. The battery is charged by the AC power while it is available, so when AC power is lost, the battery can provide power to the system for a limited amount of time, depending on the UPS system.
Chapter 1 Chapter 1 Introduction Overview The KPC-1530/1730 Panel PCs is combining the latest Intel 45nm Intel® Atom™ processor with the high integration of the Intel® 945GSE/ ICH7-M chipset for a wide range of industrial applications. Storage includes a 2.5" SATA hard drive or a solid-state drive (SSD), and slim optical drive. Supported interfaces include a GbE LAN, HD audio, 4x serial ports, USB 2.0 ports, PCI slot, and Mini PCI slot, thus easily meeting a broad range of customer requirements.
Chapter 1 Product Specifications KPC-1530 KPC-1730 CPU Intel® Atom™ N270 Intel® Atom™ N270 Chipset Intel® 945GSE + ICH7-M Intel® 945GSE + ICH7-M Memory 1x DDR2 400/533 SO-DIMM Socket, up to 2G 1x DDR2 400/533 SO-DIMM Socket, up to 2G Internal Storage 1x 2.5” SATA HDD or 1x SSD 1x 2.
Chapter 1 Mechanical Layout Front and Side Panel Figure 1 Mechanical Layout - Front and Side WARNING Be sure not to block any air vents on the computer. Blocked air vents can cause thermal problems.
Chapter 1 Mechanical Dimensions Figure 3 Mechanical Dimensions (KPC-1530) KPC-1530/ 1730 User’s Manual 16
Chapter 1 Figure 4 Mechanical Dimensions (KPC-1730) KPC-1530/ 1730 User’s Manual 17
Chapter 2 Chapter 2 Assembly/Disassembly Accessing Internal Components WARNING Before opening your system, make sure to turn it off and disconnect the power sources to prevent electric shock or system damage. And wait 3 to 5 minutes to let the computer cool before removing the computer cover. Follow the procedure described below to access the system's internal components. 1) Place the system front-side-down on a soft material to prevent marking or scratching of the front panel.
Chapter 2 Figure 6 Mechanical Internal Layout Memory Module Installation Carefully follow the steps below in order to install the DIMMs: 1. 2. 3. 4. To avoid generating static electricity and damaging the SO-DIMM, ground yourself by touching a grounded metal surface or use a ground strap before you touch the SO-DIMM. Do not touch the connectors of the SO-DIMM. Dirt or other residue may cause a malfunction. To make sure the correct DDR2 SO-DIMM notches should match with the DDR2 SO-DIMM.
Chapter 2 Figure 8 Press down on the SO-DIMM Memory Module to lock it in place Removing a DIMM: To remove the SO-DIMM, use your fingers or a small screwdriver to carefully push away the tabs that secure either side of the SO-DIMM. Lift it out of the socket. Make sure you store the SO-DIMM in an anti-static bag. The socket must be populated with memory modules of the same size and manufacturer.
Chapter 2 Follow the procedure described below to install a PCI card. 1. Remove the PCI raiser card holder (1) and PCI slot cover (2) by loosening the retaining screw as shown. 2. Fully insert the PCI card into the PCI raiser card 3. Replace PCI raiser card holder and secure with the retaining screw.
Chapter 2 HDD & ODD Installation Step 1 Remove the pre-cut bracket opening of ODD and the PCI raiser card holder. Loosen the 4 screws and take off the ODD bracket form the system. Step 2 & 3 Secure the hard drive to the HDD bracket using the short screws then secure HDD bracket to the ODD bracket using the anti-vibration screws. Step 4 Secure the ODD to the ODD bracket using the 4 short screws provided. Step 5 Secure the whole bracket to the chassis and connecting the data & power cables.
Chapter 2 VESA Mounting The product comes with VESA FDMI 75/100 standard mounting holes as shown below. Use 4 screws with the appropriate length for your mounting bracket.
Chapter 2 Wall Mounting . Below are the demonstrations of how to use Quanmax wall-mount kits Step1 Secure the VESA kit to the panel PC using the 4 screws. Step2 Install the wall-mount kit to the proper place of the wall by using the 6 screws. Step3 Attach the panel PC to the wall-mount kit which has been well fixed on the wall.
Chapter 2 Panel Mounting The Panel PC can be panel mounted and comes with brackets and screws for this purpose. The required cutout for panel mounting and maximum panel thickness is shown below.
Chapter 2 Below are the demonstrations of how to do panel mounting. Step1 Remove the pre-cut Bracket Opening Covers by firmly inserting a flathead screwdriver and bending them back and forth until they break free from the chassis. “KPC-1530: 9 Bracket Opening Covers” “KPC-1730: 10 Bracket Opening Covers” Step2 Install the Panel Mount Seal on the inside edge of the Panel PC Step3 Insert a Panel Mount Bracket into a bracket opening as shown.
Chapter 3 Chapter 3 Getting Started Power Connection CAUTION Use the power cord suitable for the power supply in your country. Do not remove or alter the grounding prong on the power cord. In situations where a two-slot receptacle is present, have it replaced with a properly grounded three-prong grounding type receptacle. AC Power 1. 2. Connect the supplied AC power cord to the system AC power inlet on the I/O panel of the system. Connect the other end of the AC power cord to a corresponding outlet.
Chapter 3 3. 4. Remove just enough insulator material from the ends of the wires to allow a proper electrical connection to the terminal block. Insert the power feed wires into the terminal block and tighten the compression clamps as shown. 5. Insert the terminal block into the DC inlet in the chassis and secure by tightening the screws loosened in Step 2. 6. 7. Connect the power distribution to the DC power feed wires. Press the power button to turn it on.
Chapter 4 Chapter 4 Maintenance and Prevention Your KPC-1530/1730 system requires minimal maintenance and care to keep it operating correctly. Occasionally wipe the system with a soft dry cloth. You should only remove persistent dirt by use of a soft, slightly damp cloth (use only a mild detergent). Make sure the ventilation holes are clear of debris.
Chapter 5 Chapter 5 Interface & Jumper Setting External Connectors Table 2 AUDIO, 3-Port Audio phone jack Signal Name BLUE LINE IN GREEN LINE OUT PINK MIC IN Table 3 USB, USB2.
Chapter 5 Table 5 COM1 RS-232/422/485 Connector (DB9) RS485 Pin RS232 RS422 1 DCD, Data carrier detect TX- DATA- 2 RXD, Receive data RX+ N/A 3 TXD, Transmit data TX+ DATA+ 4 DTR, Data terminal ready RX- N/A 5 GND, ground GND GND 6 DSR, Data set ready N/A N/A 7 RTS, Request to send N/A N/A 8 CTS, Clear to send N/A N/A 9 RI, Ring indicator (+5V / +12V *) N/A N/A Half Duplex * Voltage can be selected JP4.
Chapter 5 Table 8 CN 10, PS/2 KB/MS Connector Pin Signal Function 1 KBDAT Keyboard Data 2 NC No Connect 3 GND Ground 4 KB5V +5VSB Power Source 5 KBCLK Keyboard Clock 6 NC No Connect 7 MSDAT Mouse Data 8 NC No Connect 9 GND Ground 10 KB5V +5VSB Power Source 11 MSCLK Mouse Clock 12 NC No Connect Jumper Setting Table 9 JP4, COM1 Signal / Power Selection Jumper Setting Function 1-3 Short Pin 1 of COM1 = +12V 3-5 Short Pin 1 of COM1 = +5V 1 5-7 Short Pin 1 of COM1 = +5V Pin 1 of COM1 = DCD@RS232, 7-9 Short TX
Chapter 5 Figure 15 Jumper and Connector Locations KPC-1530/ 1730 User’s Manual 33
