KPC-1210 12.
Contact Info: Quanmax Inc. 5F, No. 415, Ti-Ding Blvd. Sec. 2, NeiHu District, Taipei, Taiwan 114 Tel: +886-2-2799-2789 Fax: +886-2-2799-7399 Visit our site at: www.quanmax.com © 2012 Quanmax Inc. All rights reserved. The information in this user’s guide is provided for reference only. Quanmax does not assume any liability arising out of the application or use of the information or products described herein.
Content Content Content....................................................................................................................... 3 Figures & Tables......................................................................................................... 4 Safety Instructions ...................................................................................................... 5 Before You Begin ..................................................................................
Figures & Tables Figures & Tables Figure 1 I/Os .............................................................................................. 15 Figure 2 Mechanical Dimensions ............................................................... 17 Figure 3 DP/ VGA/ HDMI ........................................................................... 18 Figure 4 Connect USB mouse & keyboard ................................................ 19 Figure 5 RJ45 connector ...................................................
Safety Instructions Safety Instructions Before You Begin Before handling the product, read the instructions and safety guidelines on the following pages to prevent damage to the product and to ensure your own personal safety. Refer to the “Advisories” section in the Preface for advisory conventions used in this user’s guide, including the distinction between Warnings, Cautions, Important Notes, and Notes. Always use caution when handling/operating a computer.
Safety Instructions 2. 3. 4. Disconnect the computer and peripherals from their power sources or subsystems to prevent electric shock or system board damage. This does not apply when hot swapping parts. Follow the guidelines provided in “Preventing Electrostatic Discharge” on the following page. Disconnect any telephone or telecommunications lines from the computer.
Safety Instructions Handle all sensitive components at an ESD workstation. If possible, use antistatic floor pads and workbench pads. Handle components and boards with care. Don’t touch the components or contacts on a board. Hold a board by its edges or by its metal mounting bracket. Do not handle or store system boards near strong electrostatic, electromagnetic, magnetic, or radioactive fields.
Preface Preface How to Use This Guide This guide is designed to be used as step-by-step instructions for installation, and as a reference for operation, troubleshooting, and upgrades. NOTE Driver downloads and additional information are available under Downloads on our web site: www.quanmax.com. Unpacking When unpacking, follow these steps: 1. After opening the box, save it and the packing material for possible future shipment. 2. Remove all items from the box.
Preface interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Preface account, send an email to support@quanmax.com to apply for one. All product(s) returned to Quanmax for service or credit must be accompanied by a Return Material Authorization (RMA) Number. Freight on all returned items must be prepaid by the customer who is responsible for any loss or damage caused by common carrier in transit. Returns for Warranty must include a Failure Report for each unit, by serial number(s), as well as a copy of the original invoice showing the date of purchase.
Preface turning it on. Failure to do so may cause damage to internal components, particularly the hard disk drive. Humidity High-humidity can cause moisture to enter and accumulate in the system. This moisture can cause corrosion of internal components and degrade such properties as electrical resistance and thermal conductivity. Extreme moisture buildup inside the system can result in electrical shorts, which can cause serious damage to the system.
Preface against variations on power because they use battery power to keep the server running when AC power is lost. The battery is charged by the AC power while it is available, so when AC power is lost, the battery can provide power to the system for a limited amount of time, depending on the UPS system. UPS systems range in price from a few hundred dollars to several thousand dollars, with the more expensive unit s allowing you to run larger systems for a longer period of time when AC power is lost.
Chapter 1 Chapter 1 Introduction Overview The KPC-1210 is a Fanless Industrial Panel PC with 12.1” TFT LCD touch screen display. Specifically designed for fanless, cost effective applications, the KPC-1210 is equipped with an Intel® Atom™Processor D2550 (1M Cache, 1.86 GHz), 2.5” SATA HDD or SSD space, 2x GbE LAN, 3x USB 2.0, 2x COM, Audio and VGA out,1x HDMI, 1x DP.
Chapter 1 Product Specifications CPU Support Intel® Atom™ Processor D2550 (1M Cache, 1.86 GHz) Chipset ® Intel NM10 Express chipset Memory 1x Single Channel DDR3 800/1066MHz SODIMM support (4GB max) BIOS AMI Plug & Play SPI BIOS Graphic ® Intel Graphics Media Accelerator 3650 LCD Display Size: 12.
Chapter 1 System tour Refer to the diagrams below to identify the components of the system. I/Os Figure 1 I/Os USB The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mouse devices, cameras, and hard disk drives. USB allows many devices to run simultaneously on a single computer, with some peripheral acting as additional plug-in sites or hubs. Power Switch The power switch allows powering ON and OFF the system.
Chapter 1 DP DP is a display interface used to connect a video source to a display device such as a computer monitor or a television set. HDMI HDMI connector for display output VGA D-Sub 15 pin VGA connector for display output COM D-Sub 9 pin connector for RS-232/422/485 connection Line Out The stereo headphone jack is used to connect the system’s audio out signal to amplified speakers or headphones.
Chapter 1 Mechanical Dimensions 343 x 269 x 33 mm (W x D x H) Figure 2 Mechanical Dimensions KPC-1210 User’s Manual 17
Chapter 2 Chapter 2 Getting Started Setting up your PC Connecting the monitor Connect the DP/ VGA/ HDMI cable from your display to the DP/ VGA/ HDMI port.
Chapter 2 Connecting USB mouse & keyboard Your KPC-1210 does not come with a keyboard and mouse, but you can use any USB keyboard or mouse with your computer. USB USB Figure 4 Connect USB mouse & keyboard NOTE Using a third-party USB mouse or keyboard may require software drivers. Check the manufacturer’s website for the latest software drivers. Connecting to a network device Connect one end of a network cable to the LAN port on the system rear panel and the other end to a hub or switch.
Chapter 2 COM ports COM ports with the pin definitions.
Chapter 2 Turning on the system 1. 2. 3. Connect the supplied AC power cord to the system AC power inlet on the I/O panel of the system. Connect the other end of the AC power cord to a corresponding outlet.
Chapter 2 VESA Mounting The product comes with VESA FDMI 100 standard mounting holes as shown below. Use 4 screws with the appropriate length for your mounting bracket. Figure 8 VESA Mounting Hole Locations NOTE To fasten the metal shelf, your monitor must comply with VESA100 standard. The VESA mounting kit is optional.
Chapter 2 Panel Mounting The Panel PC can be panel mounted and comes with brackets and screws for this purpose. The required cutout for panel mounting and maximum panel thickness is shown below.
Chapter 2 Below are the demonstrations of how to do panel mounting. Step1 Tightening the screws as shown right.
Chapter 3 Chapter 3 AMI BIOS Setup Overview This chapter provides a description of the AMI BIOS. The BIOS setup menus and available selections may vary from those of your product. For specific information on the BIOS for your product, please contact Quanmax. NOTE: The BIOS menus and selections for your product may vary from those in this chapter.
Chapter 3 Main Menu The BIOS Setup is accessed by pressing the DEL key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. Once you enter the BIOS Setup Utility, the Main Menu will appear on the screen. The Main Menu provides System Overview information and allows you to set the System Time and Date. Use the “<” and “>” cursor keys to navigate between menu screens.
Chapter 3 Advanced Menu Table 3 Advanced Menu BIOS SETUP UTILITY Main Advanced Boot Security Server Onboard LAN1 Controller [Enabled] Onboard LAN1 Boot [Disabled] Onboard LAN2 Controller [Enabled] Onboard LAN2 Boot [Disabled] Audio Controller [Enabled] > Display Configuration > Power Management Configuration Mgmt Save & Exit Select Screen > CPU Advanced Configuration > SATA Configuration > USB Configuration > Super IO Configuration > H/W Monitor ↑↓ Select Item Enter: Select +- Ch
Chapter 3 Table 4 Advanced Menu – Display Configuration BIOS SETUP UTILITY Main Advanced Boot Security Server Mgmt Save & Exit Display Configuration Fixed Graphics Memory Size IGFX – Boot Type [128 MB] [VBIOS Default] Active LFP [ Int-LVDS] LCD Panel Color [18 Bit] LCD Panel Type LVDS Backlight Control – Voltage [1024X768 18Bit 1CH] [2.5V] Select Screen ↑↓ Select Item Enter: Select +- Change Opt.
Chapter 3 Table 5 Advanced Menu –Power Management Configuration BIOS SETUP UTILITY Main Advanced Boot Security Server Mgmt Save & Exit Power Management Configuration ACPI Sleep State [S3 (Suspend to RAM)] Restore AC Power Loss Resume By PCIE Device Resume By RTC Alarm [Power Off] [Disabled] [Disabled] EUP Power Saving Mode [Disabled] >Watchdog Timer Configuration Select Screen ↑↓ Select Item Enter: Select +- Change Opt.
Chapter 3 Table 6 Advanced Menu –CPU Advanced Configuration BIOS SETUP UTILITY Main Advanced Boot Security Save & CPU Advanced Configuration Hyper-Treading [Enabled] Execute Disable Bit [Enabled] Limit CPUID Maximum EIST [Disabled] [Enabled] Select Screen ↑↓ Select Item Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc.
Chapter 3 Table 7 Advanced Menu –SATA Configuration BIOS SETUP UTILITY Main Advanced Boot Security Save & Exit Select Screen [ AHCI ] ↑↓ Select Item Configure SATA as SATA Port 1 SATA Port 2 TOSHIBA MK8046 (80.0G) Not Present Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc.
Chapter 3 Table 9 Advanced Menu – Super IO Configuration BIOS SETUP UTILITY Main Advanced Boot Security Save & Exit Select Screen Super IO Configuration ↑↓ Select Item >Serial Port 1 Configuration >Serial Port 2 Configuration Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc.
Chapter 3 Table 11 Advanced Menu – Super IO Configuration – Serial Port 2 Configuration BIOS SETUP UTILITY Main Advanced Boot Security Save & Serial Port 2 Configuration Serial Port Device Settings [Enabled] IO=2F8h; IRQ=3; Select Screen Change Settings Serial Port 2 Type [Auto] [RS232] ↑↓ Select Item Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc.
Chapter 3 Table 12 Advanced Menu –H/W Monitor BIOS SETUP UTILITY Main Advanced Boot Security Save & PC Health Status CPU Warning Temperature [Disabled] CPU Temperature : +41 C : +36 C SYS Temperature Select Screen ↑↓ Select Item +3.3V +VCORE +VGFX +1.05V +1.5V +5VDUAL +VIN +3.3VSB : +3.344 V : +1.192 V : +1.008 V : +1.064 V : +1.517V : +5.120V : +12.144 V : +3.360 V Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.
Chapter 3 Boot Menu Table 13 Boot Menu BIOS SETUP UTILITY Main Advanced Boot Security Save & Boot Configuration Full Screen LOGO Display [Disabled] Setup Prompt Timeout Bootup NumLock State 1 [On] Boot Option Priorities Select Screen Boot Option #1 Boot Option#2 Hard Drive BBS Priorities [UEFI: SanDisk] [SATA PM: TOSHIBA…] ↑↓ Select Item Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219.
Chapter 3 Security Menu Table 14 Security Menu BIOS SETUP UTILITY Main Advanced Boot Security Save & Exit Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup Select Screen If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup.
Chapter 3 Save Changes and Exit Exit system setup after saving the changes. Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select [Yes] to save changes and exit. Discard Changes and Exit Exit system setup without saving any changes.
Chapter 4 Chapter 4 Driver Installation If your KPC-1210 does not come with an operating system pre-installed, you will need to install an operating system and the necessary drivers to operate it. After you have finished assembling your system and connected the appropriate power source, power it up using the power supply and install the desired operating system. You can download the drivers for the KPC-1210 from the Quanmax website at www.quanmax.com and install as instructed there.
