HPC-1010 10.
Contact Info: Quanmax Inc. 5F, No. 415, Ti-Ding Blvd. Sec. 2, NeiHu District, Taipei, Taiwan 114 Tel: +886-2-2799-2789 Fax: +886-2-2799-7399 Visit our site at: www.quanmax.com © 2012 Quanmax Inc. All rights reserved. The information in this user’s guide is provided for reference only. Quanmax does not assume any liability arising out of the application or use of the information or products described herein.
Content Content Content....................................................................................................................... 3 Figures & Tables......................................................................................................... 4 Safety Instructions ...................................................................................................... 5 Before You Begin ..................................................................................
Figures & Tables Figures & Tables Figure 1 I/Os .............................................................................................. 15 Figure 2 Mechanical Dimensions ............................................................... 17 Figure 3 DVI- I/ HDMI ................................................................................ 18 Figure 4 Connect USB mouse & keyboard ................................................ 19 Figure 5 RJ45 connector ...............................................
Safety Instructions Safety Instructions Before You Begin Before handling the product, read the instructions and safety guidelines on the following pages to prevent damage to the product and to ensure your own personal safety. Refer to the “Advisories” section in the Preface for advisory conventions used in this user’s guide, including the distinction between Warnings, Cautions, Important Notes, and Notes. Always use caution when handling/operating a computer.
Safety Instructions When Working Inside a Computer Before taking covers off a computer, perform the following steps: 1. Turn off the computer and any peripherals. 2. Disconnect the computer and peripherals from their power sources or subsystems to prevent electric shock or system board damage. This does not apply when hot swapping parts. 3. Follow the guidelines provided in “Preventing Electrostatic Discharge” on the following page. 4.
Safety Instructions Preventing Electrostatic Discharge Static electricity can harm system boards. Perform service at an ESD workstation and follow proper ESD procedure to reduce the risk of damage to components. Quanmax strongly encourages you to follow proper ESD procedure, which can include wrist straps and smocks, when servicing equipment.
Preface Preface How to Use This Guide This guide is designed to be used as step-by-step instructions for installation, and as a reference for operation, troubleshooting, and upgrades. NOTE Driver downloads and additional information are available under Downloads on our web site: www.quanmax.com. Unpacking When unpacking, follow these steps: 1. After opening the box, save it and the packing material for possible future shipment. 2. Remove all items from the box.
Preface interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Preface account, send an email to support@quanmax.com to apply for one. All product(s) returned to Quanmax for service or credit must be accompanied by a Return Material Authorization (RMA) Number. Freight on all returned items must be prepaid by the customer who is responsible for any loss or damage caused by common carrier in transit. Returns for Warranty must include a Failure Report for each unit, by serial number(s), as well as a copy of the original invoice showing the date of purchase.
Preface turning it on. Failure to do so may cause damage to internal components, particularly the hard disk drive. Humidity High-humidity can cause moisture to enter and accumulate in the system. This moisture can cause corrosion of internal components and degrade such properties as electrical resistance and thermal conductivity. Extreme moisture buildup inside the system can result in electrical shorts, which can cause serious damage to the system.
Preface Uninterruptible Power Supply Uninterruptible power supply (UPS) systems offer the most complete protection against variations on power because they use battery power to keep the server running when AC power is lost. The battery is charged by the AC power while it is available, so when AC power is lost, the battery can provide power to the system for a limited amount of time, depending on the UPS system.
Chapter 1 Chapter 1 Introduction Overview The HPC-1010 10.1” Panel PC is combining the Intel® Atom™ processor N2800 with the high integration of the Intel® NM10 Express chipset for a wide range of industrial applications. Storage includes a 2.5" SATA hard drive or a solid-state drive (SSD). Supported interfaces include 2x GbE LAN, 1x COM port, 6x USB 2.0 ports, 1x SATA,1x HDMI, 1x DVI-I thus easily meeting a broad range of customer requirements.
Chapter 1 Product Specifications CPU Support ® Intel Atom™ Processor N2800 (1M Cache, 1.86 GHz) Chipset ® Intel NM10 Express chipset Memory 1x Single Channel DDR3 800/1066MHz SODIMM support (4GB max) BIOS Graphic Touch Sensor AMI Plug & Play SPI BIOS ® Intel Graphics Media Accelerator 3650 5-wire resistive touch sensor Size: 10.
Chapter 1 System tour Refer to the diagrams below to identify the components of the system. I/Os Figure 1 I/Os USB The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mouse devices, cameras, and hard disk drives. USB allows many devices to run simultaneously on a single computer, with some peripheral acting as additional plug-in sites or hubs. Power Button The power button allows powering ON and OFF the system.
Chapter 1 DC Jack The supplied power adapter converts AC power to DC for use with this jack. Power supplied through this jack supplies power to the PC. To prevent damage to the PC, always use the supplied power adapter. HDMI HDMI connector for display output COM D-Sub 9 pin connector for RS-232/422/485 connection DVI-I The DVI-I (Digital Visual Interface-Integrated) connector allows you to connect an LCD monitor. It provides a high-speed digital interconnection between the computer and its display device.
Chapter 1 Mechanical Dimensions 261.98 x 199.
Chapter 2 Chapter 2 Getting Started Setting up your PC Connecting the monitor Connect the HDMI / DVI-I cable from your display to the HDMI / DVI-I port.
Chapter 2 Connecting USB mouse & keyboard Your HPC-1010 does not come with a keyboard and mouse, but you can use any USB keyboard or mouse with your computer. USB USB Figure 4 Connect USB mouse & keyboard NOTE Using a third-party USB mouse or keyboard may require software drivers. Check the manufacturer’s website for the latest software drivers. Connecting to a network device Connect one end of a network cable to the LAN port on the system rear panel and the other end to a hub or switch.
Chapter 2 COM port COM port with the pin definitions.
Chapter 2 Turning on the system 1. 2. 3. 4.
Chapter 2 VESA Mounting The product comes with VESA FDMI 75 standard mounting holes as shown below. Use 4 screws with the appropriate length for your mounting bracket. Figure 8 VESA Mounting Hole Locations NOTE To fasten the metal shelf, your monitor must comply with VESA75 standard. The VESA mounting kit is optional.
Chapter 2 Wall Mount Kit Below are the demonstrations of how to use Quanmax wall-mount kits Step1 Secure the VESA kit to the panel PC using the 4 screws. (M4x5L flat head) Step2 Install the wall-mount kit to the proper place of the wall by using the 6 screws. Step3 Attach the panel PC to the wall-mount kit which has been well fixed on the wall.
Chapter 2 Desktop Stand Step1 Assembling the desktop stand Step2 Secure the VESA kit to the desktop stand using the 4 screws. (M4x5L round head) Step3 Secure the panel PC to the desktop stand using the 4 screws.
Chapter 2 Operating System and Drivers If your product does not come with an operating system pre-installed, you will need to install an operating system and the necessary drivers to operate it. After you have finished assembling your system and connected the appropriate power source, power it up using the power supply and install the desired operating system. You can download the drivers for the product from the Quanmax website at www.quanmax.com and install as instructed there.
Chapter 3 Chapter 3 AMI BIOS Setup Overview This chapter provides a description of the AMI BIOS. The BIOS setup menus and available selections may vary from those of your product. For specific information on the BIOS for your product, please contact Quanmax. NOTE: The BIOS menus and selections for your product may vary from those in this chapter.
Chapter 3 Main Menu The BIOS Setup is accessed by pressing the DEL key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. Once you enter the BIOS Setup Utility, the Main Menu will appear on the screen. The Main Menu provides System Overview information and allows you to set the System Time and Date. Use the “<” and “>” cursor keys to navigate between menu screens.
Chapter 3 Advanced Menu Table 3 Advanced Menu BIOS SETUP UTILITY Main Advanced Boot Security Server M gmt Save & Onboard LAN1 Controller [Enabled] Onboard LAN1 Boot [Disabled] Onboard LAN2 Controller [Enabled] Onboard LAN2 Boot [Disabled] Select Screen Audio Controller [Enabled] ↑↓ Select Item Enter: Select +- Change Opt.
Chapter 3 Table 4 Advanced Menu – Display Configuration BIOS SETUP UTILITY Main Advanced Boot Security Display Configuration Server M gmt Save & Select Screen Fixed Graphics Memory Size [128 MB] IGFX – Boot Type [VBIOS Default] Active LFP [ Int-LVDS] +- Change Opt. [1024X600 18Bit 1CH] [2.5V] F1: General Help LCD Panel Type LVDS Backlight Control – Voltage M ↑↓ Select Item Enter: Select F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219.
Chapter 3 Table 5 Advanced Menu –Power Management Configuration BIOS SETUP UTILITY Main Advanced Boot Security Server M gmt Save & Power Management Configuration ACPI Sleep State [S3 (Suspend to RAM)] Restore AC Power Loss Resume From S3 By PS/2 Keyboard Resume From S3 By PS/2 Mouse [Power Off] [Disabled] [Disabled] Resume By PCIE Device Resume By RTC Alarm [Disabled] [Disabled] Select Screen ↑↓ Select Item Enter: Select +- Change Opt.
Chapter 3 Table 6 Advanced Menu –CPU Advanced Configuration BIOS SETUP UTILITY Main Advanced Boot Security Save & CPU Advanced Configuration Hyper-Treading [Enabled] Execute Disable Bit [Enabled] Limit CPUID Maximum EIST [Disabled] [Enabled] Select Screen ↑↓ Select Item Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc.
Chapter 3 Table 7 Advanced Menu –SATA Configuration BIOS SETUP UTILITY Main Boot Advanced Security Save & Exit Select Screen Configure SATA as ↑↓ Select Item [ AHCI ] SATA Port 1 SATA Port 2 TOSHIBA MK8046 (80.0G) Not Present Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc.
Chapter 3 Table 9 Advanced Menu – Super IO Configuration BIOS SETUP UTILITY Main Boot Advanced Security Super IO Configuration Save & Exit Select Screen ↑↓ Select Item >Serial Port 1 Configuration Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011, American Megatrends, Inc.
Chapter 3 Table 11 Advanced Menu –H/W Monitor BIOS SETUP UTILITY Main Advanced Boot Security Save & PC Health Status CPU Warning Temperature [Disabled] Select Screen CPU Temperature : +55 C SYS Temperature : +47 C ↑↓ Select Item Enter: Select +- Change Opt. +VCORE +VGFX +3.3V +5V +VIN +1.05V +1.5V +USBVCC : +1.056 V : +0.960 V : +3.376 V : +5.016 V : +12.160V : +1.072V : +1.508 V : +4.989 V F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.
Chapter 3 Boot Menu Table 12 Boot Menu BIOS SETUP UTILITY Main Advanced Boot Security Save & Boot Configuration Full Screen LOGO Display [Disabled] Setup Prompt Timeout Bootup NumLock State 1 [On] Boot Option Priorities Select Screen Boot Option #1 Boot Option#2 Hard Drive BBS Priorities ↑↓ Select Item [UEFI: SanDisk] [SanDisk] Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219.
Chapter 3 Security Menu Table 13 Security Menu BIOS SETUP UTILITY Main Advanced Boot Save & Security Exit Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup.
Chapter 3 Save Changes and Exit Exit system setup after saving the changes. Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select [Yes] to save changes and exit. Discard Changes and Exit Exit system setup without saving any changes.
Chapter 4 Chapter 4 Driver Installation If your HPC-1010 does not come with an operating system pre-installed, you will need to install an operating system and the necessary drivers to operate it. After you have finished assembling your system and connected the appropriate power source, power it up using the power supply and install the desired operating system. You can download the drivers for the HPC-1010 from the Quanmax website at www.quanmax.com and install as instructed there.
