ASSEMBLY INSTRUCTION SKU CODE: (WF286845/WF286846/WF286847) This set included 3 boxes if do not receive full 3 boxes .
SAFETY WARNINGS ! This bed is designed for use only mattress(es) meeting the following specifications on the upper bunk, and lower bunk: Bed Type Length Width Thickness Full Standard 74-75" 5372" 8" max Replacement parts, including additional guardrails, may be obtained from any of our (CLOUDED TECHNOLOGY(USA) INC) dealers Follow the information on the wakings appearing on the upper bunk bed end structure and on the carton. Do not remove waning label from bed.
OPTION 2:SLICE ON THE RIGHT CE AAT \—Zh 7 VAN NZ 7 NII RAN SIT X \ SSN REE on NTI NY TREES 04/30
Hardware List (sam [ILS Screws 1/4" x100 Steel Bracket PCs 4pe Wood Screws PCs 210 x 40 mm Screws 1/4" x50 21/4" x 80 mm Wood dowel PCs PCs Hex-Head bolts PCs 21/4" x 13 mm M4x30 mm @1/4" x 30 mm Horizontal-Hole bolts PCs Wood screws PCs Hex-Head bolts PCs Screws 1/4" x70 21/4" x 35 mm PCs Allen Key 1pc Hex-Head bolts PCs @1/4" x 15 mm 212 x 110 mm M3.
1 ~N 4x2pcs B 8 2 ing hardware #1 connect A1 Following below illustration Assembly Bottom bed's Headboard and Foot board. Usi STEP 1: ith B3 Frame to complete Frame to complete LEFT side of Bottom Bed.
1 4x2pcs Following below illustration Assembly Center bed's Headboard and Foot board. Using hardware #1 connect STEP 2-1: |A3 and A4 legs with B2 Frame to complete LEFT side of Center Bed.
2 PCs) oe PCs) hollowing below illustration. . Using hardware #3 connect Steel with Uncomplicated On Step 2-1). STEP 2-2: .
1 Following below illustration Assembly Upper bed's Headboard and Foot board. Using hardware #1 connect JA7 and AB legs with B2 Frame to complete LEFT side of Upper Bed.
FN PCs PCs PCs follow detail view to Assembly Bottom bed's Headboard and Foot board with sidewall Following below Illustration Using hardware #6 #7 and dowel #4 at detail view for more detail 16/30 Inside Side Rail View
re PCs connect bed (completed on step 8) with Ladder (completed on step Following below Illustration: -Using hardware #8 to 18/30
12 STEP 1 0 + Following below illustration . 1 3 Using hardware #12#13 connect Frame(completed on Step 8) [Frame(completed on step 8) o Put Support Slat (D2) on Bracket PCs) PCs) Ne If you use option 1 is D=345mm If you use option 2 is D=495mm STEP 1 1 + Following below illustration: -Screw 14 slats D1 using hardware #8.
re PCs [Using hardware #9 to connect bed (completed on step 11) with Ladder (completed on step 4) STEP 1 2: Following below Illustration: 21/30
re PCs [Using hardware #9 to connect bed (completed on step 14) with Ladder (completed on step 4) STEP 15: Following below illustration: 24/30
FN FN PCs PCs TRA WAT A INNER 7 ANY Ne 7 Deanne PCs) PCs) ~ ~ Damon 0 ~— (aed [ Joey a) WAST 7 NN NW SHE WAT SN GO IAT ONE WN O TTS CONCH WN QOR Nea Lay the Center Bed (completed on step 12) on Bottom Bed (completed on step 7) using the Dowel #14 and Dowel #4. [Then use Screw #3, #15 to temperament fix Center and Bottom Bed STEP 1 6: Following below Illustration.
FN PCs FN PCs < Deanne NITA 4 ® ANZ) 7 a 4 INC 7/ AVIAN /, 7/7 DIN TRY “o\ NZ NAAN RZ \\ (aed PCs) “1 14 Lay the Upper Bed (completed on step 15) on Bed (completed on step 18) using the Dowel #14 and Dowel #4. [Then use Screw #3, #15 to permanent fix Canter and Upper Bad STEP 1 7: Following below Illustration.
STE P 1 8-3 spins below alliteration Using hardware #5,Dowel 18 to Assembly Siide. Look at detail view for more detail STE P 1 8-4 rowing below illustration Using hardware #3 #17 to Assembly Slide.
a PCs | posts) Cs S——x CIC ZN 20 NZ -Aging hardware #9 to connect bed (completed on step 17) with Ladder (completed on step 4} -Using hardware #3 to Assembly Slide with Bed. Look at detail view for more detail STE P 1 Orion below illustration X SAX ANN yA \ X N\N\VETA \ \ \ \ 3 \ AJA) SYA OPTION 1 29/30 Inside Side Rail View
— = 30/30 oes ~~ N ACZ=0 ANZ —Z2) Aan. NISSAN STE P 1 Orion below illustration OPTION 2 Inside Side Rail View -Aging hardware #9 to connect bed (completed on step 17) with Ladder (completed on step 4} -Using hardware #3 to Assembly Slide with Bed.
