Product Name: Construction Tux Harness Part #: 02100; 02110; 02120; 02130; 02140; 02200; 02210; 02220; 02240; 02105; 02115; 02125; 02135; 02145; 02705; 02715; 02725; 02735; 02745; 02700; 02710; 02720; 02730; 02740; 13010; 13020; 13030; 13610; 13620; 13630; 13200; 13210; 13220; 13230; 13240; 13300; 13310; 13220; 13330; 13340; 12305; 12315; 12325; 12335; 12345; 02600; 02610; 02620; 02630; 02640; 02405; 02415; 02425; 02435; 02445; 02305; 02315; 02325; 02335; 02345; 02205; 02215; 02225; 02235; 02245; 03010; 030
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St.
Trainer: User: Applicable Safety Standards When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.1-2007, and ANSI A10.32-2012 standards for fall protection. Applicable standards and regulations depend on the type of work being done, and also might include state regulations if applicable. Consult regulatory agencies for more information on personal fall arrest systems and associated components.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Safety Information ! WARNING Failure to understand and comply with safety regulations may result in serious injury or death. Regulations included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person’s judgment or knowledge of federal or state standards. Do not alter equipment. Do not misuse equipment.
Prior to EACH use, all equipment in a fall protection system must be inspected for any potential or existing deficiencies that may result in its failure or reduced functionality. IMMEDIATELY remove equipment from service if any deficiencies are found. Equipment must be inspected by a Competent Person at least every six months. These inspections must be documented in equipment instruction manual and on equipment inspection grid label.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Repairs to Construction Tux Harnesses can only be made by a Guardian Fall Protection representative or an entity authorized by Guardian. Contact Guardian for all maintenance and repair needs at: 1-800-466-6385. If a Construction Tux Harness fails inspection in any way, immediately remove it from service, and contact Guardian to inquire about its return or repair.
Personal Fall Arrest: A Construction Tux Harness may be used in Personal Fall Arrest applications as a component of a Personal Fall Arrest System (PFAS). Structure must withstand loads applied in the directions permitted by the system of at least 5,000 lbs. Maximum free fall is 6’, unless used in combination with equipment explicitly certified for extended free fall. Applicable D-ring: Dorsal. Restraint: A Construction Tux Harness may be used in Restraint applications.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Limitations Fall Clearance: There must be sufficient clearance below the anchorage connector to arrest a fall before the user strikes the ground or an obstruction. When calculating fall clearance, account for a MINIMUM 3’ safety factor, deceleration distance, user height, length of lanyard/SRL, and all other applicable factors.
Two or more snap hooks or carabiners connected to each other. NO. Connector directly to webbing. NO. Two connectors to same D-ring. NO. Incompatible or irregular application, which may increase risk of roll-out. NO. 8 Application that places load on gate. NO. Connector directly to horizontal lifeline. NO. www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Connector to integral lanyard. NO. 6305 S. 231st St., Kent, WA 98032 Connector closed and locked to D-ring. OK.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Correct Anchorage Positioning: This chart details allowable working zones required to reduce risk of swing falls and improper side loading. ALWAYS adhere to information specified by chart.
www.guardianfall.com Components and Specifications Made from some or all of the following materials: Banox FR3, Nylon Mesh, Cotton Duck, and Polyester.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Installation and Use ALL PFAS equipment must be selected and deemed compatible with the Construction Tux Harness by a Competent Person. ALWAYS follow all instructions of all equipment used in combination with the Construction Tux Harness. ALWAYS ensure all product-specific application specifications are met and adhered to.
www.guardianfall.com Some steps of adorning a harness may require assistance from another person. Upon completely adorning a harness, Guardian Fall Protection recommends that another person, with knowledge of the safe and correct use of the harness, inspect to ensure the harness is being worn correctly. 4. Adjust chest strap height to lower chest level, approximately 6” from top of shoulders. Connect chest strap. Ensure there is no twisting of webbing. 12 5.
TION ET SA F NF MANCE Ƒ SM Ƒ S-M Ƒ MED Ƒ LG Ƒ XL-XXL Ƒ M-XL Ƒ L-XL Ƒ XL Ƒ XXL Ƒ S-L Ƒ M-L Material: Polyester ! ADVENTENCIA ADVENTENCIA: QUITE DE SERVICIO si súbdito a una caída accesorio o si la unida falla la inspección. Before use inspect equipment for rips, tears, fraying, or any possible structural deficiency that might compromise the equipment in a fall. See instruction manual for installation procedures. Avoid contact with sharp and abrasive surfaces.
This inspection log must be specific to one Construction Tux Harness. Separate inspection logs must be used for each Construction Tux Harness. All inspection records must be made visible and available to all users at all times. If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE. Guardian Fall Protection Notes www.guardianfall.com Date of First Use: __________________.
