Installation Manual Installation and Appliance Setup INSTALLER: Leave this manual with party responsible for use and operation. Owner: Retain this manual for future reference. NOTICE: DO NOT discard this manual! R Models: SAPH-MBK-IPI SAPH-MBK-IPIL SAPH-D-PMH-IPI SAPH-D-PMH-IPIL SAPH-D-MBK-IPI SAPH-D-MBK-IPIL SAPH-D-CSB-IPI SAPH-D-CSB-IPIL WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
Safety Alert Key: • • • • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE: Used to address practices not related to personal injury. Table of Contents Installation Standard Work Checklist. . . . . . . . . . . . . . . . . . . . .
Installation Standard Work Checklist ATTENTION INSTALLER: Follow this Standard Work Checklist This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.
1 Product Specific and Important Safety Information D. High Altitude Installations A. Appliance Certification MODELS: SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBKIPI, SAPH-D-CSB-IPI LABORATORY: Underwriters Laboratories, Inc. (UL) NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.
Note: The following requirements reference various Massachusetts and national codes not contained in this document. H.
2 Getting Started A. Design and Installation Considerations C. Inspect Appliance and Components Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. • Carefully remove the appliance and components from the packaging. Installation MUST comply with local, regional, state and national codes and regulations.
3 Framing and Clearances A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. B A E C F BACK D SIDE FRONT ELECTRICAL CORD GAS LINE Location Inches Millimeter Location Inches Millimeter A 22 557 D 19-3/4 501 B 9-3/8 238 E 11 279 C 27-5/8 701 F 20-3/4 526 NOTE: Diagrams show gas appliance equipped without optional Blower, Part #GFK-160A. Figure 3.
B. Clearances to Combustibles C. Hearth Extension/Floor Protection When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 3.2). CAUTION! Risk of Fire or Injury! Install appliance on a stable, level, platform or floor strong enough to support appliance without tipping. WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.
4 Termination Location and Vent Information A. Vent Termination Minimum Clearances ! A WARNING 18 in. minimum 457 mm 20 in. and over 0 in. minimum Fire Risk. Gas, Wood or Fuel Oil Termination Cap Maintain vent clearance to combustibles as specified. • DO NOT pack air space with insulation or other materials. B Failure to keep insulation or other materials away from vent pipe may cause overheating and fire. HORIZONTAL OVERHANG 2 FT. MIN. 20 INCHES MIN. B 6 in. (minimum) up to 20 in.
B. Chimney Diagram O N P R F C Q V B J B V D V H or i B V G V V H V X M A V V E H L V V V A K Electrical Service V = VENT TERMINAL K V C X = AIR SUPPLY INLET V = AREA WHERE TERMINAL IS NOT PERMITTED A = 12 inches ����������������clearances above grade, veranda, porch, deck or balcony B = 12 inches.
C. Approved Pipe This appliance is approved for use with Hearth & Home Technologies SLP venting systems. Refer to Section 11.A for vent component information and dimensions. DO NOT mix pipe, fittings or joining methods from different manufacturers. The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall. WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent.
D. Use of Elbows Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect. See Figure 4.4. Y Y Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216 mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows. See Figure 4.4. X Figure 4.
F. Venting Guidelines for Horizontal Runs Max Horizontal Run, Rear Vent (No Rise) 14 in. (356 mm) Snorkel kit and derating orifice must be used. See Figure 4.6. G. Vent Diagrams To replace the first 90º starter elbow with two 45º elbows, refer to Figure 4.7. All other 90º elbows can be replaced with two 45º elbows. General Rules: Max Horizontal Run 14 ft (4.3 m) when vertical rise is 10 ft (3m) • SUBTRACT 3 ft. from the total H measurement for each 90º elbow installed horizontally.
Top Vent - Horizontal Termination One Elbow V1 H1 V1 H1 Maximum 1 ft. 305 mm 14 in. 356 mm 2 ft. 610 mm 9 ft. 2.7 m 4 ft. 1.2 m 10 ft., 3 in. 3.1 m 6 ft. 1.8 m 11 ft., 6 in. 3.5 m 8 ft. 2.4m 12 ft., 9 in. 3.9 m 10 ft. 3.0 m 14 ft. 4.3 m 12 ft. 3.7 m 13 ft., 2 in. 4.0 m 16 ft. 4.9 m 11 ft., 3 in. 3.4 m 20 ft. 6.1 m 9 ft., 4 in. 2.7 m 24 ft. 7.3 m 7 ft., 6 in. 2.3 m 28 ft. 8.5 m 5 ft., 7 in. 1.7 m 30 ft. 9.1 m 4 ft., 7 in. 1.4 m Figure 4.
Two Elbows V1 H2 H1 INSTALLED HORIZONTALLY 2 Elbows to Max. Horizontal V1 Minimum H1 + H2 Maximum 2 ft. 610 mm 6 ft. 1.8 m 4 ft. 1.2 m 7 ft., 3 in. 2.2 m 6 ft. 1.8 m 8 ft., 6 in. 2.6 m 8 ft. 2.4 m 9 ft., 9 in. 3.0 m 10 ft. 3.1 m 11 ft. 3.4 m 12 ft. 3.7 m 10 ft., 2 in. 3.1 m 16 ft. 4.9 m 8 ft., 3 in. 2.5 m 20 ft. 6.1 m 6 ft., 4 in. 1.9 m 24 ft. 7.3 m 4 ft., 6 in. 1.4 m 28 ft. 8.5 m 2 ft., 7 in. 787 mm 30 ft. 9.1 m 1 ft. 9 in. 533 mm Figure 4.
Top Vent - Horizontal Termination - (continued) Three Elbows H2 V2 H1 V1 3 Elbows to Max. Horizontal V1 Minimum H1 + H2 Maximum 2 ft. 610 mm 3 ft. 914 mm 4 ft. 1.2 m 4 ft., 3 in. 1.3 m 6 ft. 1.8 m 5 ft., 6 in. 1.7 m 8 ft. 2.4 m 6 ft., 9 in. 2.1 m 10 ft. 3.1 m 8 ft. 2.4 m 12 ft. 3.7 m 7 ft., 2 in. 2.2 m 16 ft. 4.9 m 5 ft., 3 in. 1.6 m 20 ft. 6.1 m 3 ft., 4 in. 1.0 m 24 ft. 7.3 m 1 ft., 6 in. 457 mm 28 ft. 8.5 m 11 in. 279 mm 30 ft. 9.1 m 11 in.
Top Vent - Vertical Termination No Elbow V1 = 30 ft. Max. (9.1 m) V1 = 6 ft. Min. (1.8 m) V1 Figure 4.
Two Elbows 2 Elbows to Max. Horizontal V1 Minimum V2 V1 + V2 Maximum H1 Maximum 2 ft. 610 mm 27 ft. 4 in. 8.3 m 6 ft. 1.8 m 4 ft. 1.2 m 24 ft., 8 in. 7.5 m 7 ft., 3 in. 2.2 m 6 ft. 1.8 m 22 ft. 6.7 m 8 ft., 6 in. 2.6 m 8 ft. 2.4 m 19 ft., 4 in. 5.9 m 9 ft., 9 in. 3.0 m 10 ft. 3.1 m 16 ft., 8 in. 5.1 m 11 ft. 3.4 m 12 ft. 3.7 m 18 ft., 8 in. 5.7 m 10 ft., 2 in. 3.1 m 16 ft. 4.9 m 22 ft., 8 in. 6.9 m 8 ft., 3 in. 2.5 m 20 ft. 6.1 m 26 ft.,8 in. 8.1 m 6 ft.
Top Vent - Vertical Termination - (continued) Three Elbows 3 Elbows to Max. Horizontal V1 Minimum V2 V1 + V2 Maximum 2 ft. 610 mm 4 ft. 6 ft. H1 + H2 Maximum 30 ft. 9.1 m 6 ft. 1.8 m 1.2 m 30 ft. 9.1 m 7 ft., 3 in. 2.2 m 1.8 m 28 ft., 2 in. 8.6 m 8ft., 6 in. 2.6 m 8 ft. 2.4 m 25 ft., 6 in. 7.8 m 9 ft., 9 in. 3.0 m 10 ft. 3.1 m 21 ft. 6.4 m 11 ft. 3.4 m 12 ft. 3.7 m 24 ft., 8 in. 7.5 m 11.2 m 2.2 m 16 ft. 4.9 m 29 ft. 8.8 m 5 ft., 3 in. 1.6 m 20 ft. 6.1 m 30 ft.
Rear Vent - Horizontal Termination No Elbow H1 = 14 in. (356 mm) Maximum Note: A derating orifice is required with this application and is included in the Rear Vent Kit. Note: All horizontal vent pipe runs must have 1/4 inch rise per foot. NOTICE: An SLK-SNKD is required for this vent configuration. H1 Figure 4.14 Rear Vent - Horizontal Termination One 45º Elbow H1 = 14 in. (356 mm) Maximum Note: A derating orifice is required with this application and is included in the Rear Vent Kit.
Rear Vent - Horizontal Termination - (continued) Two Elbows 2 Elbows to Max. Horizontal V1 Minimum 2 ft. 610 mm H1 Minimum 6 in. 152 mm H1 + H2 Maximum 6 ft. H1 Maximum 1.8 m 14 in. 357 mm 4 ft. 1.2 m 6 in. 152 mm 7 ft., 3 in. 2.2 m 14 in. 357 mm 6 ft. 1.8 m 6 in. 152 mm 8-ft., 6 in. 2.6 m 14 in. 357 mm 8 ft. 2.4 m 6 in. 152 mm 9 ft., 9 in. 3.0 m 14 in.. 357 mm 10 ft. 3.1 m 6 in. 152 mm 11 ft. 3.4 m 14 in. 357 mm 12 ft. 3.7 m 6 in. 152 mm 10 ft., 2 in. 3.
Three Elbows 3 Elbows to Max. Horizontal V1 Minimum H1 Minimum H1 Maximum Htotal 2 ft. 610 mm 6 in. 152 mm 14 in. 357 mm 3 ft. 914 mm 4 ft. 1.2 m 6 in. 152 mm 14 in. 357 mm 4 ft., 3 in. 1.3 m 6 ft. 1.8 m 6 in. 152 mm 14 in. 357 mm 5 ft., 6 in. 1.7 m 8 ft. 2.4 m 6 in. 152 mm 14 in. 357 mm 6 ft., 9 in. 2.1 m 10 ft. 3.1 m 6 in. 152 mm 14 in. 357 mm 8 ft. 2.4 m 12 ft. 3.7 m 6 in. 152 mm 14 in. 357 mm 7 ft., 2 in. 2.2 m 16 ft. 4.9 m 6 in. 152 mm 14 in.
Rear Vent - Vertical Termination One Elbow H1 Minimum 6 in. 152 mm H1 Maximum 14 in. 357 mm V1 Minimum 6 ft. 1.8 m V1 Maximum 40 ft. 12.2 m Note: A derating orifice is required with this application and is included in the Rear Vent Kit. V1 H1 Figure 4.
Rear Vent - Vertical Termination - (continued) Three Elbows 3 Elbows to Maximum Horizontal V1 Minimum V2 H1 Minimum H1 Maximum Htotal V1 + V2 MAXIMUM 2 ft. 610 mm 6 in. 152 mm 14 in. 357 mm 3 ft. 914mm 33 ft., 4 in. 10.2 m 4 ft. 1.2 m 6 in. 152 mm 14 in. 357 mm 4 ft., 3 in. 6 ft. 1.8 m 6 in. 152 mm 14 in. 357 mm 5 ft., 6 in. 1.6 m 31 ft. 9.5 m 1.7 m 28 ft., 2 in. 8.6 m 8 ft. 2.4 m 6 in. 152 mm 14 in. 357 mm 6 ft., 9 in. 2.1 m 25 ft., 6 in. 7.8 m 10 ft. 3.
Class A Metal Chimney Top Adapter Prior to installing the gas stove, ensure that the existing chimney is functionally sound and clean. • Have the chimney and adjacent structure inspected Flex Pipe and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified Sheet Metal Screws professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.
Existing Masonry Chimney Prior to installing the gas stove, ensure that the existing chimney is functionally sound and clean. • Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.
to fit 1. Before cutting any holes, assemble the desired sections of direct vent pipe to determine the center of the masonry penetration. 2. Once the center point of the penetration has been determined, cut a 6 in. (152mm) diameter hole in the masonry. If the hole is too large, the retro connector might not mount properly; if the hole is too small, the appliance might starve for intake air. If there is a frame wall in front of the masonry wall, cut and frame a 10 in.
Flex Liner 6 in. (152mm) diameter opening in masonry wall Flex Coupler Sheet Metal Screws Retro Connector (3) Masonry Bolts (Not included) Figure 4.27 Figure 4.29 8. Secure the top adapter to the flashing. Use three sheet metal screws through the side of the top adapter into the flange on the flashing See Figure 4.28. Twist lock the high wind termination cap on to the top adapter. 10. Slide wall thimble cover over retro connector and secure with masonry bolts. See Figure 4.30.
Coaxial to Colinear Venting The coaxial to colinear adapter (DV-46DVA-GCL) is approved for installations into solid fuel masonry or factory built fireplaces that have been installed in accordance with the National, Provincial, State and local building codes. INLET AIR VENT PIPE EXHAUST VENT PIPE Figure 4.31 Coaxial/Colinear Appliance Connector WARNING! Risk of Fire! Coaxial to colinear venting configuration may only be used in existing non-combustible chimney.
5 Vent Clearances and Framing A. Pipe Clearances to Combustibles B. Wall Penetration Framing/Firestops WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: Combustible Wall Penetration • Between ceiling firestops • Between wall shield firestops • Around vent system Failure to keep insulation or other material away from vent pipe may cause overheating and fire. Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
C. Ceiling Firestop/Floor Penetration Framing A ceiling firestop MUST be used between floors and attics. • SLP Pipe - Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/floor (see Figure 5.3). ATTIC ABOVE • Frame the area with the same sized lumber as used in ceiling/floor joist. • The ceiling firestop may be installed above or below the ceiling joists when installed with an attic insulation shield. It must be under joists between floors that are not insulated.
6 Appliance Preparation A. Top to Rear Vent Conversion This model comes from the factory set up for a top vented application. To vent this model from the rear, follow the conversion instructions below. If venting off the top, no further preparation is needed. Proceed to next section. INNER PIPE ADAPTER See Service Parts list in Owner’s Manual for Kit information. CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
5. Remove rear access plate and gasket by removing four screws. Save the screws. See Figure 5. Figure 6. Reattach Rear Access Plate/Gasket 6. Place rear access plate and gasket over top vent and attach with the four screws removed in Figure 2. REMOVE SCREWS (6) Figure 9. Reattach Starting Collar/Gasket 8. Install starting collar with gasket or high-temp sealant to rear vent opening. Attach with screws removed in Figure 5. Place grille gently into the opening on top of appliance.
TOP CASTING FRONT CASTING PILOT ASSEMBLY MAIN BURNER ORIFICE Figure 11. Remove Casting Figure 14. 16. Reinstall burner with four screws. 17. On inside of firebox, remove plate and gasket on rear of firebox by removing three screws as shown in Figure 14. Discard gasket. Replace screws on rear of firebox. Remove three screws as shown in Figure 15. Attach plate and new gasket, included in kit, with three screws. 18. Reinstall upper baffle.
B. Securing and Leveling the Appliance WARNING! Risk of Fire! Prevent contact with combustible materials. WARNING! Risk of Fire! Failure to maintain air space clearance may cause overheating and fire. Figure 8.12 3. Use a 5/32 in. (4mm) Allen wrench to adjust legs up and down to desired level. Figure 8.10 1. Thread Allen bolts through nuts until flush. NOTE: Two Allen bolts and two nuts are included in the component bag. Normally, only one is required on the leg not touching the floor. Figure 8.11 2.
7 Venting and Chimneys A. Assemble Vent Sections To attach the first vent component to the starting collars of the appliance: • Lock the vent components into place by sliding the pipe section onto the collar. • Align the seam of the pipe and seam of collar to allow engagement. Rotate the vent component to lock into place. Use this procedure for all vent components. See Figure 7.2. • Slide the gasket over the first vent section and place it flush to the appliance. This will prevent cold air infiltration.
B. Assemble Slip Sections • Slide the inner flue of the slip section into the inner flue of the pipe section and the outer flue of the slip section over the outer flue of the pipe section. See Figure 7.3. • Slide together to the desired length. Pilot hole Figure 7.3 Slip Section Pilot Holes • Maintain a 1-1/2 in. (38 mm) overlap between the slip section and the pipe section. • Secure the pipe and slip section with two screws no longer than 1/2 in. (13 mm), using the pilot holes in the slip section.
C. Secure the Vent Sections D. Disassemble Vent Sections • Vertical runs originating off the top of the appliance, with no offsets, must be supported every 8 ft. (2.44 m) after the maximum allowed 25 ft. (7.62 m) of unsupported rise. • Rotate either section (see Figure 7.7) so the seams on both pipe sections are aligned as shown in Figure 7.8. • Vertical runs originating off the rear of the appliance, or after any elbow, must be supported every 8 ft. (2.44 m).
Install Decorative Ceiling Components A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling thimble is used to cover the firestop. • Seal the gap between the vent pipe and firestop using high temperature silicone (300º F minimum continuous exposure rating) to prevent cold air infiltration. • Install the decorative ceiling thimble by sliding it up to the ceiling and attaching it using the provided screws.
E. Vertical Termination Requirements Install Metal Roof Flashing CAULK • See minimum vent heights for various pitched roofs (Figure 7.11) to determine the length of pipe to extend through the roof. • Slide the roof flashing over the pipe sections extending through the roof as shown in Figure 7.12. HORIZONTAL OVERHANG 2 FT. MIN. 20 INCHES MIN. VERTICAL WALL LOWEST DISCHARGE OPENING Figure 7.12 GAS DIRECT VENT TERMINATION CAP 12 X ROOF PITCH IS X/ 12 H (MIN.
Assemble and Install Storm Collar Install Vertical Termination Cap CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp. • Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section. • Slide the storm collar onto the exposed pipe section and align brackets.
F. Horizontal Termination Requirements Install Decorative Wall Components (SLP only) Heat Shield Requirements for Horizontal Termination A decorative wall thimble can be installed on wall through which the vent passes. The decorative wall thimble is used to cover the wall shield firestop. WARNING! Risk of Fire! To prevent overheating and fire, heat shields must extend through the entire wall thickness.
Install Horizontal Termination Cap WARNING! Risk of Fire! The telescoping flue section of the termination cap MUST be used when connecting vent. Note: When using termination caps with factory-supplied heat shield attached, no additional wall shield firestop is required on the exterior side of a combustible wall. • 1-1/2 (38 mm) minimum overlap of flue telescoping section is required. Failure to maintain overlap may cause overheating and fire. • Vent termination must not be recessed in the wall.
8 Electrical Information A. General Information WARNING! Risk of Shock or Explosion! DO NOT wire 110-120 VAC to the valve or to the appliance wall switch. Incorrect wiring will damage controls. NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1. • Plug the cord from the appliance junction box to unswitched 110-120 VAC.
B. Wiring Requirements Intellifire™ Plus Ignition System Wiring • Plug the cord from the appliance junction box to 110-120 VAC for proper operation of the appliance. WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout. • Refer to Figure 8.1, IPI Wiring Diagram. • This appliance is equipped with an IntelliFire™ Plus control valve which operates on a 6 volt/1.5 AMP system.
Wall Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan (See Figure 8.2): • The power supply for the appliance must be brought into a switch box. • The power can then be supplied from the switch box to the appliance using a minimum of 14-3 with ground wire. • At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.
Optional Fan Installation The GFK-160A fan has been designed to circulate room air through the appliance to enhance heat output. WING NUT The GFK-160A system operates on 120 VAC, 60 Hz power. This is available through a receptacle in the factory installed junction box on the underside of the appliance. Compare CONTENTS OF CARTON with the actual parts received. If any parts are missing or damaged, contact your dealer before starting installation.
9 Gas Information A. Fuel Conversion C. Gas Connection • Make sure the appliance is compatible with available gas types. • Refer to Reference Section 3 for location of gas line access in appliance. • Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts. • Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes. B. Gas Pressure • Connect incoming gas line to the 1/2 in.
E. Air Shutter Setting Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter is set fully open at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 9.1. • Loosen the wing nuts. • Slide the wing nut to the right to close the air shutter. • Slide the wing nut to the left to open the air shutter. • Tighten the wing nuts. NOTICE: If sooting occurs, provide more air by opening the air shutter.
10 Appliance Setup A. Remove Fixed Glass Assembly B. Remove the Shipping Materials WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches. Remove shipping materials from inside or underneath the firebox. • DO NOT strike, slam or scratch glass. • DO NOT operate fireplace with glass removed, cracked, broken or scratched. C.
LOG PLACEMENT INSTRUCTIONS D. Install the Log Assembly Log Set Assembly: LOGS-TS-IPI Models: TIARAI-BK-IPI, TIARAI-BR-IPI, TIARAI-CES-IPI, SAPH-MBK-IPI, SAPH-D-MBK-IPI, SAPH-D-PMH-IPI, SAPHD-CSB-IPI, TIARAI-BK-IPIL, TIARAI-BR-IPIL, TIARAI-CES-IPIL, SAPH-MBK-IPIL, SAPH-D-MBK-IPIL, SAPH-D-PMHIPIL, SAPH-D-CSB-IPIL LOG TABS 1 3 2 Figure 1. VOID FOR LOG #3 VOID FOR LOG #2 Figure 2. Placement of Log #1 CAUTION: Logs are fragile, handle with care.
E. Install Fixed Glass Assembly WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches. • DO NOT strike, slam or scratch glass. • DO NOT operate fireplace with glass removed, cracked, broken or scratched. • Replace as a complete assembly. Reinstall the glass frame by engaging the latches at the bottom corners of the firebox with the glass frame tabs. See Figure 10.1 and 10.2 for reference.
11 Reference Materials A. Vent Components Diagrams 6-1/2 in. 165 mm 6-1/2 in. 165 mm 8-3/4 in. 222 mm 6-1/2 in. 165 mm 9-1/4 in. 235 mm 6 in. 152 mm 6-5/8 in. 168 mm SLP45 45° Elbow 6-5/8 in. 168 mm 9-7/8 in. 251 mm SLP90 90° Elbow Effective Height/ Length Effective Height/Length SLP PIPE 10-7/8 in. 276 mm 1-1/2 in. 38 mm 8-7/8 in.
A. Vent Components Diagrams (continued) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVPHSM-B will be required. 8 in. (203 mm) Heat Shield 15-1/8 in. (384 mm) Term Cap Max Effective Length 12 in.
A. Vent Components Diagrams (continued) 13 in. 330 mm 14 in. 356 mm 1-5/16 in. 34 mm 13 in. 330 mm 10-9/16 in. 269 mm SLP-DCF-BK Ceiling Firestop Black SLP-CCS-BK Cathedral Ceiling Support Box-Black 12 in. 305 mm 14-1/16 in. 357 mm 14 in. 356 mm 7-1/2 in. 192 mm 10-3/4 in. 273 mm SLP-FLEX-TRAP Horizontal Termination Kit 12-1/2 in. 318 mm SLP-TVHW Vertical Termination Cap 10-11/16 in. 271mm 28-1/2 in. 724 mm 13-1/2 in. 343 mm SLK-SNKD Snorkel Termination Cap Figure 11.
A. Vent Components Diagrams (continued) 16 IN. 406 mm 9-3/16 IN. (233 mm) 13-5/8 IN. (346 mm) 12-1/2 IN. (318 mm) 4-1/2 IN. 114 mm 15 IN. (381 mm) 16-11/16 IN. 424 mm 16-11/16 IN. (424 mm) SLP-LPC SLP Low Profile Cap 7-3/8 IN. 187 mm 14 IN. 356 mm 17-7/8 IN. 454 mm 12 IN. 305 mm Figure 11.
A. Vent Components Diagrams (continued) COAXIAL to COLINEAR VENTING LINK-DV30B Flex Liner Kit 768-380A Stainless Steel Flex Pipe DV-46DVA-GCL Coaxial/Colinear Appliance Connector LINKSQC-DV30 (COPPER) LINKSQB-DV30 (BLACK) Figure 11.
B. Accessories Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories. WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.
