Owner’s Manual Installation and Operation Model(s): QFP44 CAUTION T O N RD O A D SC I D DO NOT DISCARD THIS MANUAL • Important operating and • Read, understand and follow • Leave this manual with party responsible for maintenance instructions these instructions for safe installation and operation. use and operation. included. WARNING WARNING HOT SURFACES! If the information in these instructions is not followed exactly, a re may result causing property damage, personal injury, or death.
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. A. Congratulations Congratulations on selecting a Quadra-Fire gas replace, an elegant and clean alternative to wood burning replaces. The Quadra-Fire gas replace you have selected is designed to provide the utmost in safety, reliability, and ef ciency. As the owner of a new replace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual.
Safety Alert Key: • • • • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE: Used to address practices not related to personal injury. Table of Contents A. Congratulations B. Limited Lifetime Warranty 2 5 1 Listing and Code Approvals A. B.
14 Appliance Setup A. B. C. D. E. F. G. H. I. Remove Glass Assembly Clean the Appliance Install the Refractory Adjust the Air Shutter Adjust the Vertical Baf e Install Logs, Ember Bed & Rockwool Install Andirons Place Lava Rock and Vermiculite Reinstall Glass 54 54 54 55 56 56 58 58 58 15 Troubleshooting A. Standing Pilot Ignition System 59 16 Reference Materials A. B. C. D. E.
Î B. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTY Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.
B. Limited Lifetime Warranty (continued) gasketing, glass discoloration, rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, baf es, repots, doors, or rebox area are not covered by this warranty. Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to this noise are not covered by this warranty.
1 Listing and Code Approvals A. Appliance Certi cation D. High Altitude Installations NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction. MODELS: QFP44 LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Heater When installing above 2000 feet elevation: STANDARD: ANSI Z21.88-2003 • CSA2.33 • In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.
Note: The following requirements reference various Massachusetts and national codes not contained in this document. H.
User Guide 2 Operating Instructions • A. Gas Fireplace Safety WARNING HOT SURFACES! Glass and other surfaces are hot during operation and cool down. Hot glass will cause burns. • Do not touch glass until it is cooled • NEVER allow children to touch glass • Keep children away • CAREFULLY SUPERVISE children in same room as appliance. • Alert children and adults to hazards of high temperatures. High temperatures may ignite clothing or other ammable materials.
C. Clear Space F. Dashboard Control WARNING! DO NOT place combustible objects in front of the replace or block louvers. High temperatures may start a re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects. Figure 2.3 Dashboard Control Valve Control This knob is used to control the gas to the appliance and for starting the pilot. There are three positions, ON, OFF, PILOT.
Ignitor Battery Box G. Remote Operation By pulling the drawer forward, the ignitor battery box can be accessed to replace the AA battery as necessary. See Figure 13.2. This remote control kit has a hand held transmitter that can be used as a remote on/off or as a thermostat. The transmitter display shows the current room temperature, target temperature, timer setting, on/off status, low battery indicator, current time, burner/valve operation and fan operation.
Remote Receiver Transmitter The remote receiver has a 3-position slide switch: Important: Before operating remote control, transmitter and receiver must have matching security codes. See section ‘Matching Security Codes’. OFF/REMOTE/ON (see Figure 2.5). Receptacle on back LEARN OFF-REMOTE-ON GROUND Important: Review ‘Auto Shutdown’ section. This safety feature shuts down the replace after 9 hours of continuous operation, in ON mode only.
1. LOW - Battery power low. Replace batteries within two weeks. 2. TIMER - Indicates time remaining before system shuts off, when timerprogrammed, 9 - hour maximum setting. 3. MODE - Indicates operation MODE of system. ON indicates the system is on, either manually or thermostatically. THERMO indicates the system will automatically cycle ON/OFF, depending on programmed SET temperature. OFF indicates the entire system is turned off. 4. SET - Indicates desired SET room temperature for THERMO operation. 5.
• Press the UP or DOWN button to select the desired room temperature. The highest SET temperature is 99° F (32° C). The lowest SET temperature is 45° F (6° C). NOTE: To prevent repeated thermo-cycling of the gas appliance, the sensing unit in the transmitter will only activate the remote receiver when the temperature change exceeds 2° F (1° C) above or below the SET (desired) temperature.
Adjusting the Flame Height Operates in ON or THERMO mode signal every 15 minutes to the receiver, indicating that the transmitter is within the normal operating range of 20 feet. This remote control system allows the user to control the height of the FLAME when the gas valve is factory equipped with a FLAME CONTROLLER. Should the receiver NOT receive a transmitter signal every 15 minutes (COMMUNICATION-SAFETY feature), the RECEIVER will begin a 2 HOUR (120 minute) countdown timing function.
• • Advance the SET temperature on the transmitter to a temperature of at least 2° F (1° C) above the ROOM temperature displayed on the LCD screen and the system ame will ignite. Set the SET temperature to at least 2° F (1° C) below the room temperature and the system ame will extinguish.
I. Lighting Instructions (SP) • • For normal use, activate/deactivate your replace with the wall switch or remote control. If your replace must be deactivated for serviced or an extended period of time, follow the instructions below. FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life A. This appliance has a pilot that must be lit manually.
J. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • Turn the replace off and allow it to completely cool. • Remove xed glass assembly. See Section 14.A. • Clean xed glass assembly. See Section 3.A. • Replace the xed glass assembly and run continuously on high an additional 12 hours. This cures the materials used to manufacture the replace. NOTICE! Open windows for air circulation during replace break-in.
3 Maintenance and Service Any safety screen or guard removed for servicing must be replaced prior to operating the replace. When properly maintained, your replace will give you many years of trouble-free service. We recommend annual service by a quali ed service technician. A. Maintenance Tasks-Homeowner Doors, Surrounds, Fronts Frequency: Annually By: Homeowner Tools needed: Protective gloves, stable work surface • • Assess condition of screen and replace as necessary.
Venting Control Compartment and Firebox Top Frequency: Seasonally Frequency: Annually By: Homeowner By: Quali ed Service Technician Tools needed: Protective gloves and safety glasses. • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc. • Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See Section 6. • Inspect for corrosion or separation.
Figure 3.
4 Getting Started Installer Guide A. Typical Appliance System NOTICE: Illustrations and photos re ect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual Note: Dual venting con gurations ARE NOT allowed. Appliance MUST be vented EITHER vertically OR horizontally.
B. Design and Installation Considerations D. Inspect Appliance and Components Quadra-Fire direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. • Installation MUST comply with local, regional, state and national codes and regulations.
5 Framing and Clearances A. Select Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). NOTICE: Illustrations re ect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference. WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.
To further prevent drafts, the wall shield and ceiling restops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room. B. Construct the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system.
D. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as speci ed. Framing or nishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc). Mantels 12 in. (308 mm) maximum depth Mantel Non-combustible Face A A = 53 in. (1346 mm) min. Non-combustible Mantel A = 66 in. (1676 mm) min. Combustible Mantel Figure 5.
6 Termination Locations A. Vent Termination Minimum Clearances Direct Vent Gas, Wood or Fuel Oil Termination WARNING 20 in. Fire Risk. Maintain vent clearance to combustibles as speci ed. • DO NOT pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause overheating and re. (508 mm) A (minimum) to Perpendicular Wall (DV only) 18 in. (457 mm) B Gas Termination Horizontal overhang 24 in. min. (610 mm) Termination Cap 20 in.
H D O E N V L V C B Fixed Closed V F V B Openable Fixed Closed V V G V B B B V J X M V I A V TERMINATION CAP K X V A GAS METER X AIR SUPPLY INLET Measure vertical clearances from this surface Q RESTRICTION ZONE (TERMINATION NOT ALLOWED) V P W V R V T U Electrical Service U V D* S V Covered Alcove Applications Measure horizontal clearances from this surface.
7 Vent Information and Diagrams A. Approved Pipe Vertical 12 in . DO NOT mix pipe, ttings or joining methods from different manufacturers. The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall. 8-1/2 in. This appliance is approved for use with Hearth & Home Technologies DVP venting systems. Refer to Section 16.B. for vent component information. 8-1/2 in. WARNING! Risk of Fire or Asphyxiation.
E. Vent Diagrams To replace the rst starter elbow with two 45° elbows, refer to Figure 7.4. All other 90° elbows can be replaced with two 45° elbows. General Rules: • SUBTRACT 3 ft. from the total H measurement for each 90° elbow installed horizontally. SUBTRACT 1-1/2 ft. from the total H measurement for each 45° elbow installed horizontally. A maximum of three 90° elbows (or six 45° elbows) may be used in any vent con guration. Some elbows may be installed horizontally. See Figure 7.9.
1. Top Vent - Horizontal Termination - (continued) Two 45° Elbows replacing One 90° Elbow 4 ft min. (1.22 m) 3 ft min. (.91 m) 17 ft max. (5.18 m) Figure 7.4 Three Elbows V1 H1 V2 H2 3 ft (.91 m) 3 ft (.91 m) 4 ft (1.22 m) 4 ft (1.22 m) 6 ft (1.83 m) 8 ft (2.45 m) 8 ft (2.45 m) 12 ft (3.66 m) Installed Vertically H2 V2 V1 H1 Figure 7.
2. Top Vent - Vertical Termination Note: If installing a vertical vent/termination off the top of the appliance, the ue restrictor should be used. See Section 14.E. for necessary damper adjustment. No Elbow 12 ft (3.66 m) min. 60 ft (18.29 m) max. Figure 7.7 Two Elbows 3 ft m (.91 12 ft (3.66 m) min. 60 ft (18.29 m) max. Maximum horizontal run is 100% of vertical, but cannot exceed 18 ft (5.49 m) Figure 7.
2. Top Vent - Vertical Termination - (continued) Three Elbows Maximum horizontal run is 100% of vertical, but cannot exceed 26 ft (7.92 m) 12 ft (3.66 m) min. 60 ft (18.29 m) max. Figure 7.
8 Vent Clearances and Framing A. Pipe Clearances to Combustibles B. Wall Penetration Framing WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: Combustible Wall Penetration • • • Between ceiling restops Between wall shield restops Around vent system Failure to keep insulation or other material away from vent pipe may cause over heating and re. Whenever a combustible wall is penetrated, you must frame a hole for the wall shield restop(s).
C. Install the Ceiling Firestop A ceiling restop MUST be used between oors and attics. • Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ oor (see Figure 8.3). • Frame the area with the same sized lumber as used in ceiling/ oor joist. • The ceiling restop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between oors that are not insulated. Refer to Figure 8.4.
D. Install Attic Insulation Shield WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield. The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation. Attic shields must meet speci ed clearance and be secured in place. Flat Ceiling Installation • Remove one shield from box.
9 Appliance Preparation A. Secure and Level the Appliance WARNING! Risk of Fire! Prevent contact with: • • • Sagging or loose insulation Insulation backing or plastic Framing and other combustible materials Block openings into the chase to prevent entry of blown-in insulation. Make sure insulation and other materials are secured. DO NOT notch the framing around the appliance standoffs. Failure to maintain air space clearance may cause overheating and re.
10 Install Vent Pipe A. Assemble Vent Sections Attach Pipe to the Firebox Assembly Note: The end of the pipe sections with the lanced tabs will face towards the appliance. Attach the rst pipe section to the starting collar: • • • • Lanced pipe end to the starting collar Inner pipe over inner collar Push the pipe section until all lanced tabs snap in place Lightly tug on pipe to con rm it has locked.
B. Assemble Slip Sections WARNING! Risk of Fire or Asphyxiation! Overlap pipe sections at least 1 1/2 in. (38 mm). Secure slip sections with two screws which must not exceed 1/2 in. (13 mm) in length. Use the pilot holes. Pipe could separate if not properly joined. • • Slide the inner ue of the slip section into the inner ue of the pipe section and the outer ue of the slip section over the outer ue of the pipe section. See Figure 10.5. Slide together to the desired length. Figure 10.
C. Secure the Vent Sections D. Disassemble Vent Sections • • Vertical runs of pipe must be supported every 8 ft. (2.44 m) after the 25 ft. (7.62 m) maximum unsupported rise. Horizontal sections of vent must be supported every 5 ft. (1.52 m) with a vent support or plumber’s strap. Wall shield restops may be used to provide horizontal support. Vent support or plumber’s strap (spaced 120° apart) may be used for support. See Figures 10.7 and 10.8. • • • • Rotate either section (see Figure 10.
Note: Skip to Section 10.I. if using the RF4-8. NOTICE: Failure to properly caulk the roof ashing could cause water entry. • • E. Install Metal Roof Flashing • See minimum vent heights for various pitched roofs (Figure 10.11) to determine the length of pipe to extend through the roof. Slide the roof ashing over the pipe sections extending through the roof as shown in Figure 10.12. • Caulk the gap between the roof ashing and the outside diameter of the pipe.
F. Assemble and Install Storm Collar CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp. • Connect both halves of the storm collar with two screws (see Figure 10.13). Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly (Figure 10.14).
G. Install RF4-8 The SLP-FS shown in this photo will not be used with DVP pipe. The RF4-8 may be used in place of the roof ashing and storm collar. Pipe must be supported within 12 in. (305 mm) of the roo ine using plumbers strapping when using the RF4-8 Flashing. Refer to Sect. 10.C. Securing Vent Sections. SLP-FS • • • • • • • Trim the rubber boot (using scissors or a utility knife), cutting along the marked measurement lines. See Figure 10.15. Use the 210 mm line for DVP pipe.
H. Install Vertical Termination Cap • • Attach the vertical termination cap by sliding the inner collar of the cap into the inner ue of the pipe section while placing the outer collar of the cap over the outer ue of the pipe section. Secure the cap by driving three self-tapping screws (supplied) through the pilot holes in the outer collar of the cap into the outer ue of the pipe (see Figure 10.19). Termination Cap I.
• J. Install Horizontal Termination Cap WARNING! Risk of Fire! The telescoping ue section of the termination cap MUST be used when connecting vent. • 1-1/2 (38 mm) minimum overlap of ue telescoping section is required. Failure to maintain overlap may cause overheating and re. • • Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base. Flash and seal as appropriate for siding material at outside edges of cap.
11 Gas Information A. Fuel Conversion • Make sure the appliance is compatible with available gas types. Conversions must be made by a qualified service technician using Hearth & Home Technologies speci ed and approved parts. • Converting to LP Gas Note: Gas conversions should only be performed by a quali ed service person, and/or where required by state and local codes, licensed installer/service technician.
• • Replace 2 screws holding pilot bracket to burner. Pull hood keeper from pilot and lift hood off pilot assembly. See Figure 11.5. • • • • • • • • • • • Replace hood and keeper. Loosen locknut on the Hi-Lo Solenoid using 11/16 wrench. Remove solenoid from the valve by turning counterclockwise. Use a screwdriver and turn pressure screw clockwise ¾ turn. Attach manometer to outlet side of the valve. Light unit. Fine tune pressure with screwdriver.
B. Gas Pressure C. Gas Connection • • Optimum appliance performance requires proper input pressures. Gas line sizing requirements will be determined in ANSI Z221.3 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada. Pressure requirements are: • • Natural Gas Propane Minimum inlet pressure Gas Pressure 5.0 in. w.c. 11.0 in. w.c. Maximum inlet pressure 7.0 in. w.c. 14.0 in. w.c. Manifold pressure 3.5 in. w.c. 10.0 in. w.c.
12 Electrical Information B. Standing Pilot Ignition System Wiring A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1. • Wire the appliance junction box to 110-120 VAC. This is required for use of optional accessories.
D. Electrical Service and Repair WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. WARNING! Risk of Shock! Replace damaged wire with type 105° C rated wire. Wire must have high temperature insulation. Figure 12.1 Wiring Diagram E.
13 Finishing A. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as speci ed. Framing or nishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc). Mantels 12 in. (308 mm) maximum depth Mantel Non-combustible Face A A = 53 in. (1346 mm) min. Non-combustible Mantel A = 66 in. (1676 mm) min. Combustible Mantel Figure 13.
B. Facing Material • • • • The QFP44 is shipped with non-combustible material in place. Do not cover or replace this non-combustible material with combustible materials. - The non-combustible front upper can be removed if replaced with non-combustible materials. See Section 1.E. for materials that may be used. Combustible nish wall material may be butted up to the unit and the supplied non-combustible material of the upper front. - The unit is shipped with door templates attached.
14 Appliance Setup WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty. C. Install the Refractory • • A. Remove Glass Assembly Remove the refractory retainer from each side of the rebox. Put the left side refractory in place and reinstall the left side refractory retainer.
• Install the upper back refractory. D. Adjust the Air Shutter This appliance has adjustable air shutters (which control the primary air) factory set in the closed position (approximately 1/8 in. open). See Figure 14.6. NOTICE: If sooting occurs, provide more air by opening the air shutter. Figure 14.4 Install Upper Back Refractory • • Install the right side refractory. Slide the back refractory slightly from side to side as necessary to close up any gaps in the corners.
• E. Adjust the Vertical Baf e If the vertical run height is more than 12 feet, it may be necessary to install the vertical baf es that are included with the unit to improve the ame appearance. Install each baf e to cover the outside two slots in the lower rebox top. See Figure 14.7. Position ember bed over the burner locating the corners inside the brackets. See Figure 14.9. Figure 14.
• Position the right front log over the grate bars, aligning the cut outs on the bottom of the log with the bars. See Figure 14.12 • Place the end of the right middle log on the at area on the ember bed and position the hole in the log over the exposed locator pin on the front log. See Figure 14.15. Figure 14.12 Positioning Right Front Leg • Position the cutout on the bottom of the left log over the locating bracket on the grate.
WARNING! Risk of Explosion! Follow rockwool placement instructions. DO NOT place rockwool directly over burner ports. Replace rockwool material annually. Improperly placed rockwool interferes with proper burner operation. • • Rockwool is shipped with this gas appliance. Place individual pieces of wool loosely in the ember bed slots. Do not block the burner ports by packing tightly. H.
15 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali ed service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a quali ed service technician. Contact your dealer to arrange a service call by a quali ed service technician. A. Standing Pilot Ignition System Symptom 1.
Troubleshooting (continued) Symptom 3. (Continued) Possible Cause Corrective Action C. Failed valve. Turn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter should read greater than 125mV. If the reading is acceptable, and if the burner does not come on, replace the gas valve. D. Plugged burner ori ce. Check the burner ori ce for stoppage. Remove stoppage. E. Wall switch or wires.
16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. 25° TYP 35-5/8 in. 905 mm 29-1/2 in. 749 mm 19-1/5 in. 495 mm 15-1/8 in. 384 mm 66-3/8 in. 1686 mm 35-1/2 in. 902 mm Gas Line 57-3/4 in. 1467 mm Electrical Hookup 2-1/4 in. 57 mm 10-1/8 in. 257 mm 40 in. 1016 mm 49 in. 1245 mm Figure 16.1 Appliance Dimensions 60 Quadra-Fire • QFP44 • 4051-300 Rev M • 09/08 2-7/8 in.
B. Vent Components Diagrams Effective Height/Length mm Pipe inches DVP4 DVP6 DVP12 DVP24 DVP36 DVP48 DVP6A DVP12A Effective Height/Length 4 6 12 24 36 48 3-6 3 - 12 4-7/8 in. (124 mm) 102 152 305 610 914 1219 76 - 152 76 - 305 10-1/2 in. (267 mm) 45° 10-7/8 in. (276 mm) DVP45 45° Elbow DVP Pipe (see chart) 10 in. (254 mm) 11-3/8 in. (289 mm) 1 in. (25 mm) 7-3/8 in. (187 mm) 9-1/4 in. (235 mm) 13-1/4 in. (337 mm) Assembled Height: 24 in./610 mm Diameter: 10 in.
B. Vent Components Diagrams (continued) 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) 27-1/2 in. (698 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF12M Roof Flashing Multi-pak RF6M Roof Flashing Multi-pak 13-3/4 in. (349 mm) 5 in. (127 mm) 5 in. (127 mm) 11-7/8 in. (302 mm) 13-7/8 in. (352 mm) 13-3/4 in. (349 mm) BEK Trap Cap Brick Extension DVP-BEK2 DVP-HPC Cap Brick Extension 11-5/8 in. (295 mm) 12-1/8 in. (308 mm) 7-1/8 in. (181 mm) 5-3/4 in.
B. Vent Components Diagrams (continued) 7-1/4 in. (184 mm) 12-1/2 in. (318 mm) 5-1/4 in. (133 mm) DVP-TVHW Vertical Termination Cap (High wind) 14 in. (356 mm) 16-7/8 in. (429 mm) 12 in. (305 mm) 7-1/8 in. (181 mm) 12-1/8 in. (314 mm) 8-3/4 in. (222 mm) 1-5/8 in. (41 mm) DVP-HPC High Performance Cap Figure 16.
B. Vent Components Diagrams (continued) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required. 8 in. (203 mm) Heat Shield 15-1/8 in. (384 mm) Term Cap Minimum Effective Length Maximum Effective Length 3-1/8 in. 4-5/8 in.
Quadra-Fire • QFP44 • 4051-300 Rev M • 09/08 6 5 3 Log Set Assembly 21 1 2 22 20 4 7 23 24 19 18 16 15 25 17 28 29 8 12 Refractory Assembly 26 27 14 10 32 11 9 30 31 13 Top Left Log PART NUMBER Burner Assembly 18 4051-024 Additional service part numbers on following page 4051-300 28746 Installation Instructions & Owner’s Manual 14333B Vermiculite Lava Rock Bag Assembly 4021-297 4051-185 4040-094 Vertical Baf e (QTY 2) Mineral Wool 4000-225 Flue Gasket Lava R
1 5 11 4 3 6 2 7 8 9 14 10 12 19 24 20 21 18 13 17 16 23 22 26 15 25 Quadra-Fire • QFP44 • 4051-300 Rev M • 09/08 25 26 Y Y 44CKN 44CKP Conversion Kit - NG Conversion Kit - LP Y Y 200-2420 200-2630 Pilot Injector - 51 - NG Pilot Injector - 35 - LP Y Y 4021-381 HTI-16-006 Y Y Remote Transmitter Wall Holder 582-856 Front Ori ce - LP (#56C) Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Stocked at Depot Remote Transmitter 582-846 Front Ori ce - NG (#46C
D.
E. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns. For the location of your nearest Quadra-Fire dealer, please visit www.Quadra-Fire.com.
