Owner`s manual

Page24
7014-179D
December 16, 2011
R
CB 1200 Pellet Stove
E. Fire Characteristics
Aproperlyadjustedrewiththeheatoutputcontrolswitchset
on“high”hasashortactiveamepatternthatextendsoutof
therepotapproximately4to6inches(102to152mm).If
therehastallameswithblacktailsandseemssomewhat
lazy,thefeedratewillneedtobereduced.Thisisdoneby
slidingthefueladjustmentcontrolroddown,whichwillreduce
thefeed.Ifthereisnot4to6inches(102to152mm)tall,
slidethefueladjustmentcontrolroduptoincreasethefeed.
Amediumandlowsettingwillgiveashorterame.Theame
willriseandfallsomewhat.Thisisnormal.
Figure 24.1
C. Before Your First Fire
1. First, make sure your appliance has been properly
installedandthatallsafetyrequirementshavebeenmet.
Payparticularattentiontothereprotection,ventingand
thermostatinstallationinstructions.
2. Double check that the ash drawer and firebox are
empty!
3. Checkthepositionofthethermocouple,locatedabove
therepot,andmakesurethatitprotrudesapproximately
3/4inch(19mm)intotherepot.
4. Closethefrontdoor.
NOTICE: Thetipofthethermocouplemustbeincontact
with the inside end of the thermocouple cover or missed
ignitionscanoccur.
Thefeedadjustmentcontrolrodisfactoryset,andshould
beadequateformostfuels. Thesetscrewislocatedatthe
bottom of the hopper and set loose at the factory so the
fueladjustmentcontrolrodwillslideupanddownbyonly
looseningthethumbscrewatthetop.See Figure 24.1. Do
notre-tightenbottomsetscrew.
However,iftheflameheightistoohighortoolow,youwill
needtoadjustthefeedrate.Waituntiltheappliancehasbeen
burningfor15minutesbeforemakingyouradjustmentsand
a llow15minutesforfeedadjustmenttotakeeffect. 
1. Loosenthethumbscrew.Figure 24.1
2. Adjustthefueladjustmentcontrolrodtowardsthe"+" 
symbol to increase the feed rate and ame height or
towardsthe"-"symbol,todecreasethefeedrateand
ameheight.
3. Re-tightenthethumbscrew.
F. Feed Rate Adjustment Instructions
D. Starting Your First Fire
1. A thermostat is required for proper operation of this
appliance,exceptforcorn.Atthistime,llthehopper
withpellets,setthethermostattoitslowestsetting.Plug
thepowercordintonearbyoutlet.
2. The exhaust blower will stay on for approximately 10
minutes even though the thermostat is not calling for
heat.Thisisnormal.
3. L ocate the heat output control switch mounted on the
upperright corner ofthe right sidepanel.  Switchit to
thehighsettingbypushingthetopoftheswitchin,then
adjustthethermostattoitshighestsetting.Theredcall
lightlocated ontheupperrightcorner oftherightside
panelwillbeon.Thisindicatesthethermostatiscalling
forheat.
4. Thefuelfeedsystemandtheignitershould now beon.
5. Foryourrstreitwillbenecessarytopressthereset
buttoneverytwominutesuntilpelletsstarttodropinto
therepot,thenpressbutton1moretime.Thiswillllthe
feedsystemandallowtheappliancetobegindropping
pellets.Theappliancewillcontinuetorunaslongasthe
thermostatiscallingforheat.
6. Once the appliance has ignited, let the it burn for
approximately15minutes,thensetthethermostattothe
desiredroomtemperature.Adjusttheheatoutputcontrol
switchtothedesiredsetting.
Fuel Adjustment
Rod
Thumb
Screw
Set Screw