AcousticDesign™ Series User Guide S8T – 8" two-way, foreground/background loudspeaker with 70/100V transformer S10T – 10" two-way, foreground/background loudspeaker with 70/100V transformer S12 – 12" two-way, foreground/background loudspeaker TD-000329-01-A TD-000329-01
EXPLANATION OF SYMBOLS The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death. The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in damage to the equipment that may not be covered under the warranty. The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of the procedure.
Warranty (USA only; other countries, see your dealer or distributor) QSC Audio Products 3 Year Limited Warranty QSC Audio Products, LLC (”QSC”) guarantees its products to be free from defective material and/or workmanship and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and use, provided the unit is returned to our factory, one of our authorized service stations or an authorized QSC International Distributor via pre-paid
Set the Transformer Tap Switch Refer to Figure 1 1. Insert a 4mm flat-tip screwdriver into Transformer Tap hole and engage the slot. 2. At fully clockwise the transformer is in 8-bypass. 4mm S10T 100 Volt 70 Volt 8Ω 8Ω N/A 100W 100W 50W 50W 25W 25W 12.5W — Figure 2 — — Figure 1 — — Table 1 — S8T 100 Volt 70 Volt 8Ω 8Ω N/A 60W 60W 30W 30W 15W 15W 7.
Adjust the Angle of the X-Mount™ Bracket Refer to Figure 5 NOTE: This step may be done now or after mounting the loudspeaker. 1. Use a 5mm hex wrench to loosen the adjustment locking screws. 2. Orient the bracket as necessary. -15°/+30° 5 mm up to +/-70º +/-15º SIDE TOP FRONT — Figure 5 — 3. Tighten the adjustment locking screws.
Mount the Loudspeaker on the Bracket Refer to Figure 6. NOTE: The loudspeaker can be placed on the mount in ANY direction (Up, Down, Left, Right). 4 1. Align the "X" slot with the X-Mount™ bracket and push the loudspeaker onto the bracket. (1) 2. When seated, pull the loudspeaker down to lock the loudspeaker onto the bracket. (2) 3. (Optional) Remove and retain the security tab (3); pull straight out. To remove the loudspeaker, re-install the security tab, press in and then remove the loudspeaker.
Install the Weather Cover (Optional) Refer to Figure 8 1. Slide the nut (1), compression gasket (2), and weather cover / gasket (3) over the wiring for the loudspeaker. 2. Terminate the wiring to the Euro-style connector, refer to "Wire the Loudspeaker" on page 7 3. Install the Euro-style connector. 4. Slide the weather cover/gasket (3) up next to the connection box, use a small amount of wire, inside the cover, to provide strain relief. 5.
596 mm (23.4 in) 323 mm (12.7 in) S12 Dimensions 354 mm (13.9 in) 596 mm (23.4 in) 354 mm (13.9 in) 323 mm (12.
516 mm (20.3 in) 298 mm (11.7 in) S10T Dimensions 318 mm (12.5 in) 516 mm (20.3 in) 318 mm (12.5 in) 298 mm (11.
440 mm (17.3 in) 251 mm (9.9 in) 8T Dimensions 254 mm (10 in) 440 mm (17.
Specifications S8T S10T S12 8” 2-way with transformer 10” 2-way with transformer 12” 2-way 1” Exit / 1.4” Voice-coil Compression Driver 8” Weather Resistant Paper Cone Woofer, 2.0” / 50 mm Voice-coil 1” Exit / 1.4” Voice-coil Compression Driver 10” Weather Resistant Paper Cone Woofer, 2.5” / 64 mm Voice-coil 1” Exit / 1.
Mailing Address: QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA Telephone Numbers: Main Number: (714) 754-6175 Sales & Marketing: (714) 957-7100 or toll free (USA only) (800) 854-4079 Customer Service: (714) 957-7150 or toll free (USA only) (800) 772-2834 Facsimile Numbers: Sales & Marketing FAX: (714) 754-6174 Customer Service FAX: (714) 754-6173 World Wide Web: www.qscaudio.com E-mail: info@qscaudio.com service@qscaudio.com © 2013 QSC Audio Products, LLC.
