TS-101 Turbo Station User Manual (Version: 2.0.0) ©Copyright 2007. QNAP Systems, Inc. All Rights Reserved.
FOREWORD Thank you for choosing QNAP products! instructions of using TS-101. This user manual provides detailed Please read carefully and start to enjoy the powerful functions of TS-101! NOTE • All features, functionality and other product specifications are subject to change without prior notice or obligation. • All brands and products names referred to are trademarks of their respective holders. LIMITED WARRANTY In no event shall the liability of QNAP Systems, Inc.
Table of Contents Table of Contents .....................................................................................3 Safety Warnings .......................................................................................6 Chapter 1 Overview of TS-101 Turbo Station ........................................7 1.1 Introduction ...................................................................................7 1.2 Package Contents........................................................................
3.4.6 Multimedia Station................................................................... 64 3.4.7 Download Station .................................................................... 65 3.4.8 Web Server ............................................................................ 66 3.4.9 DDNS Service ......................................................................... 67 3.4.10 3.5 View Network Settings........................................................... 69 Device Configuration ..
.2 Enable iTunes Service .................................................................. 110 5.3 Use UPnP Media Server ................................................................ 112 Chapter 6 Download Station ............................................................. 115 Chapter 7 Web Server ....................................................................... 125 Chapter 8 FTP Server ........................................................................
Safety Warnings 1. TS-101 can operate normally in the temperature of 0ºC-35ºC and relative humidity of 0%-85%. Please make sure the environment is well-ventilated. 2. The power cord and devices connected to TS-101 must provide correct supply voltage (36W, 90-264V). 3. Do not place TS-101 in direct sunlight or near chemicals. Make sure the temperature and humidity of the environment are in optimized level. 4. Unplug the power cord and all connected cables before cleaning. Wipe TS101 with wet towel.
Chapter 1 1.1 Overview of TS-101 Turbo Station Introduction Thank you for choosing TS-101 Turbo Station. This product has the following key features: 9 9-in-1 server: Multimedia Station, Download Station, Mirror Station, Disaster Recovery, Web Server, Backup Server, File Server, FTP Server, and Printer Server.
1.
1.
Chapter 2 2.1 Install TS-101 Install Hard Disk 1. Unfasten the two round head screws at the back of TS-101. Pull out the front case of TS-101 as shown below: Pull Pull 2. Install a hard disk in TS-101 drive plate. Make sure the disk holes of the disk match the holes of drive plate. Lock the disk with flat head screws.
3. After installing the disk, cover TS-101 with the front case and fasten the round head screws. Then place TS-101 vertically on the stands.
2.2 Hard Disk Recommendation List The following HDD models are verified by QNAP that are compatible with TS-101. It is recommended to use the disk models listed here. Other HDD brands that are not tested by QNAP may or may not work properly with TS-101. For more updated compatible hard disk information, please visit QNAP website at http://www.qnap.com.
Maxtor Model Name Capacity Rotational (GB) Speed (RPM) Buffer Size (MB) Model No. Interface Grizzly 3H500F0 SATA II 3Gb/s 500 7200 16 Grizzly 3H400F0 SATA II 3Gb/s 400 7200 16 DiamondMax 10 6L300S0 SATA 1.5Gb/s with NCQ 300 7200 16 DiamondMax 10 6B300S0 SATA 1.5Gb/s with NCQ 300 7200 16 DiamondMax 10 6L250S0 SATA 1.5Gb/s with NCQ 250 7200 16 MaxLine Plus II 7Y250M0 SATA 1.5Gb/s 250 7200 8 DiamondMax 10 6L200M0 SATA 1.
2.3 Set up TS-101 Please check your network environment and select the appropriate installation method before installing TS-101. 1. Office/ Home Connect TS-101 and PC to the same hub/ switch/ router. 2. Individual Connect TS-101 directly to your PC by a network cable.
When you have verified your network environment, please follow the steps below to install TS-101. * Note: Please connect a USB printer to the server after the software configuration is completed.
2.4 Check System Status TS-101 provides LED indicators for you to indicate system status and information easily. When TS-101 is turned on, please check the following items to make sure system status is normal.
LED Display & System Status Overview LED n Power o Network p eSATA q HDD LED Display & System Status Blue: System has started Blink in orange: Accessing network Blink in orange: Accessing data Blink in orange: Accessing data Green: System is normal Blink in green: Hard disk not detected Blink in red: Bad blocks are found in hard disk r Status Blink in green for 5 seconds, blink in green and red alternatively: Hard disk not initialized Blink in green and red alternatively: Disk capacity is almost full (l
2.5 Configure Software Settings After checking the system status, please follow the steps below to configure the software settings of TS-101. The configuration procedure of Windows® and Mac users are different. Please select the appropriate procedure according to your OS. 2.5.1 Windows® Users Insert TS-101 CD-ROM in your PC. Wait for a few seconds until the following screen shows up. Then start to configure the software settings of TS-101. 1. Select TS-101.
2. Select Install Quick Install Wizard.
3. Run Quick Install Wizard. When the wizard prompts for performing quick configuration, click OK. 4. Enter the default user name and password.
When you have entered quick configuration page, follow the instructions to complete the settings. Click Next to continue.
Step 1. Enter the server name and click Next.
Step 2. Enter a new password or select to use the original password. Click Next to continue.
Step 3. Select the time zone of your location or enter the date and time manually. You can also select to synchronize the time of TS-101 with an Internet time server automatically. Click Next to continue.
Step 4. Select the encoding language of TS-101 and click Next. Note: All files and directories on TS-101 will be created using Unicode encoding. If your FTP client or PC does not support Unicode, e.g. Windows® 95, 98, ME OS, select the language the same as the OS of your PC here in order to view the files and directories on the server properly.
Step 5. It is recommended to use DHCP protocol to acquire IP address automatically. If your network does not support DHCP, please enter the IP address settings and click Next. Note: If you select to enter IP address manually, please make sure your PC and TS-101 are in the same LAN. If you are not sure about the network settings, please contact your network administrator or ISP.
Step 6. When a new hard disk is installed in TS-101, select “Initialize the hard disk now” and click Next to format and initialize the disk. Warning: All disk data will be cleared after disk initialization.
Step 7. You have finished quick configuration. Please make sure all settings are correct and click Next to start disk formatting.
Step 8. Please wait patiently when the disk is being formatted. Formatting may take a few minutes depending on the capacity of your hard drive. When the disk is formatted, click Next to proceed.
Congratulations! You have finished Quick Configuration. Your TS-101 is ready to use. TS-101 provides several default share folders for data sharing and access. To map the share folders on TS-101 as your drive, check the option “Continue to map network drive for me” and follow the steps below to proceed. To start to use TS-101 immediately, you can skip to 5.
a. For example, to map the folder Public as your drive, select the folder and click Map Network Drive. Note: The share folders Qdownload, Qmultimedia, Qusb, and Qweb are system default network share of TS-101 for the use of Download Station, Multimedia Station, USB Auto-copy and Web Server. b. Enter the default user name and password.
c. Select the drive letter for the connection and click Finish. d. Upon successful connection, you can start to use the share folder on TS101. You can access these folders by opening My Computer.
5. Quick Install Wizard will appear when all configurations are completed. Click on the name of TS-101 on the list to enter administration page.
6. When the administration page of TS-101 is shown, you can start to use the services. If you have any questions during web administration, please click the help button on the top right hand corner of the page. To modify system settings, click Administration. Enter the user name and password to login. Default user name: administrator Password: admin Note: 1. It is recommended to use Internet Explorer 6.0 or above to access TS-101. If the OS of your PC is Windows® 98, TS-101 supports Internet Explorer 6.
2.5.1.1 Using Mozilla Firefox For higher security, some Firefox versions will close the ports of certain services. The default port for TS-101 administration is 6000. To use port 6000 to access TS-101 via Firefox, you need to open this port in Firefox via the following steps. (1) Enter about:config in the browser. (2) A list of settings will be shown. Right click the page and select New and click String. (3) Enter network.security.ports.banned.override in the dialog and click OK.
(4) Then enter 6000 and click OK. (5) The setting will be added to the list. You can now use Firefox to access port 6000 of TS-101.
2.5.2 Mac Users A. Connect TS-101 by Mac directly or B. Connect TS-101 by the network. A. Connect TS-101 by Mac directly 1. Please go to Network settings and select Using DHCP. Then connect TS101 to your Mac via a cable. 2. Open a web browser and enter the default IP address of TS-101 to login the system. Default IP of TS-101: http://169.254.100.100:6000 Note: It is recommended to access TS-101 by Mozilla Firefox in Mac. Safari does not support Download Station of TS-101. Please refer to Chapter 2.5.1.
3. When the administration page is shown, click Administration. Enter the default user name and password to login.
4. Follow the step-by-step guide in Quick Configuration to complete the settings of TS-101. If you have any questions during web administration, please click the help button on the top right hand corner of the page.
B. Connect TS-101 by the network 1. Please go to Network settings to check and write down the subnet and router address of your Mac. Then select Using DHCP. Note: If you are not sure about the network settings, please contact your network administrator or ISP. 2. Connect TS-101 to your Mac by a cable. Open a web browser and enter the default IP address of TS-101. Default IP address of TS-101: http://169.254.100.100:6000 Note: It is recommended to access TS-101 by Mozilla Firefox in Mac.
3. When the administration page is shown, click Administration. Enter the default user name and password to login.
4. Go to TCP/IP Configuration of Network Settings . Select to use static IP and input the IP address of TS-101. Make sure the value does not conflict with the IP address of your Mac and other devices in LAN. Configure the subnet mask and default gateway of TS-101 to the same as subnet mask and router address of Mac which you set in Step 1. Click Apply to confirm. Note: When using static IP, please make sure your Mac and TS-101 are in the same subnet.
Chapter 3 Start to Enjoy the Powerful Services of TS-101 TS-101 provides the following powerful functions and applications. A. Use network share-Public folder 1. You can access the public folder of TS-101 by the following means: a. Open My Network Places and find the workgroup of TS-101. If you cannot find the server, please browse the whole network to search for TS-101. Double click the name of TS-101 for connection. b. Use Run function in Windows.
B. Manage TS-101 Manage TS-101 using web browser by Windows® or Mac 1. You can access TS-101 web administration page by the following methods: a. Use Quick Install Wizard to find TS-101. b. Open a web browser and enter http://[TS-101 IP]:6000# Note: 1. It is recommended to use Microsoft® Internet Explorer 6.0 or above to access TS-101. If the OS of your PC is Windows® 98, TS-101 supports Internet Explorer 6.0 only. 2. Please use Mozilla Firefox to access TS-101 in Mac.
2. When the administration page is shown, click Administration, Web File Manager, Web Server, Multimedia Station, or Download Station. Enter the user name and password, and then start to manage TS-101. 3. TS-101 supports SSL secure login which enables you to configure and manage the server by encrypted transfer. To use this function, check the box SSL login on the administration page and login the server.
C. Use TS-101 Services Multimedia Station TS-101 provides a user-friendly web management interface for you to manage and share personal albums and multimedia files via network easily. Supports embedded iTunes Server music sharing, UPnP and DLNA standard multimedia technology to establish home multimedia sharing center. Please refer to Chapter 5. Download Station TS-101 supports BT, HTTP, and FTP download.
Backup Server NetBak Replicator is a powerful backup software designed for Windows® users to configure automatic backup schedule. Block level remote replication is supported to provide the most reliable, instant and secure data backup mechanism. Please refer to Chapter 10. File Server TS-101 provides convenient and secure file server functions that support central data management. Users can be granted with the right to access network share and share important files. Please refer to Chapter 3.
3.
3.2 Quick Configuration Please follow the step-by-step guide in Quick Configuration to complete the settings of TS-101. If you have any questions during web administration, please click the help button on the top right hand corner of the page. Other buttons are described as below: : Return to previous page : Return to home page : Logout system Step 1. Enter the server name.
Step 2. Change the administrator password or select to use the original password. Step 3. Enter the date, time and select the time zone for the server. Step 4. Select the language the server uses to display files and directories. The default setting is English.
Step 5. Enter the IP address, subnet mask and default gateway for the server. Note: 1. Please contact your ISP or network administrator for the IP address of primary and secondary DNS servers. When TS-101 plays the role as a terminal and needs to perform independent connection, e.g. BT download, you must enter at least one DNS server IP for proper URL connection. Otherwise, the function may not work properly. 2.
Step 7. When TS-101 is initialized, the basic settings will be shown.
3.3 System Settings Basic system settings include the server name, date, time, and view system settings. 3.3.1 Server Name Enter the name of TS-101. The server name can be 14 characters long at maximum, which supports alphabets, numbers and hyphen (-). The server does not accept names with space, period (.), or names in pure number.
3.3.2 Date & Time Set the date, time, and time zone according to your location. If the settings are incorrect, the following problems may occur: 9 When using a web browser to access the server or save a file, the display time of the action will be incorrect. 9 The time of event log displayed will be inconsistent with the actual time when an action occurs.
3.3.3 Encoding Setting Select the language TS-101 uses to display files and directories. Note: All files and directories on TS-101 will be created using Unicode encoding. If your FTP clients or the OS of your PC does not support Unicode, e.g. Windows® 95/98/ME, select the language the same as your OS here in order to view the files and directories on the server properly. 3.3.4 View System Settings You can view all current system settings, e.g. server name, on this page.
3.4 Network Settings You can configure network settings in this section and enable several powerful applications of TS-101, e.g. Multimedia Station, Download Station, and Web Server. 3.4.1 TCP/ IP Configuration You can select one of the following two methods to configure the TCP/IP settings of TS-101. • Obtain IP address settings automatically via DHCP If your network supports DHCP, TS-101 will use DHCP protocol to retrieve the IP address and related information automatically.
Primary DNS Server: Enter the IP address of primary DNS server that provides DNS service for TS-101 in external network. Secondary DNS Server: Enter the IP address of secondary DNS server that provides DNS service for TS-101 in external network. Note: 1. Please contact your ISP or network administrator for the IP address of primary and secondary DNS servers. When TS-101 plays the role as a terminal and needs to perform independent connection, e.g.
Jumbo Frame Settings (MTU) "Jumbo Frames" refer to Ethernet frames that are larger than 1500 bytes. It is designed to enhance Ethernet networking throughput and reduce the CPU utilization of large file transfers by enabling more efficient larger payloads per packet. Maximum Transmission Unit (MTU) refers to the size (in bytes) of the largest packet that a given layer of a communications protocol can transmit. TS-101 uses standard Ethernet frames: 1500 bytes by default.
3.4.2 Microsoft Networking Enable file service for Microsoft networking: If you are using Microsoft® Windows®, enable this service to access the files on network share folders. Assign a workgroup name. 9 Standalone Server Use local users for user authentication. 9 WINS server If the local network has a WINS server installed, specify the IP address. TS101 will automatically register its name and IP address with WINS service.
9 Domain Master There is a unique Domain Master Browser for collecting and recording resources and services available for each PC in the network or workgroup of Windows. When you find the waiting time for accessing Network Neighborhood too long, it may be caused by failure of an existing master browser, or there is no master browser in the network.
3.4.3 Apple Network To use TS-101 on Apple Mac operating system, enable AppleTalk network support. If your AppleTalk network uses extended networks, and is assigned with multiple zones, assign a zone name to TS-101. If you do not want to assign a network zone, enter an asterisk (*) to use the default setting. This setting is disabled by default. 3.4.4 Web File Manager To access files on TS-101 via web browser, enable Web File Manager.
3.4.5 FTP Service When you enable FTP service, you can define the port number for the service and maximum number of users connected to the FTP at the same time. Select to enable or disable Unicode Support. The default setting is No.
You can enable anonymous login to allow users to access the FTP server of TS101 anonymously. The users can access the folders and files which are opened for public access. If this option is disabled, users must enter an authorized user name and password to access the server.
3.4.6 Multimedia Station To share multimedia files like photos, music or video files on the network, please enable Multimedia Station. For further information of Multimedia Station, iTunes service and UPnP Media Server, please refer to Chapter 5.
3.4.7 Download Station TS-101 supports BT, HTTP and FTP download independent of PC/notebook. To use download function of TS-101, please enable Download Station. For further information, please refer to Chapter 6. Warning: Please be warned against illegal downloading of copyrighted materials. The Download Station functionality is provided for downloading authorized files only. Downloading or distribution of unauthorized materials may result in severe civil and criminal penalty.
3.4.8 Web Server You can publish your own server by enabling Web Server function of TS-101. Enter the port number for web server service, the default number is 80. For further information, please refer to Chapter 7.
3.4.9 DDNS Service To set up a server on the Internet and enable users to access it easily, a fixed and easy-to-remember host name is often required. However, if ISP provides only dynamic IP address, the IP address of the server will change from time to time and is difficult to recall. You can enable DDNS service to solve the problem. After enabling DDNS service of TS-101, whenever TS-101 restarts or the IP address is changed, TS-101 will notify the DDNS provider immediately to record the new IP address.
Note: The DDNS function of TS-101 is not applicable when TS-101 is located behind an NAT router. Since the IP address sent from TS-101 to DDNS provider is virtual, which cannot be found on the Internet, the user will not be able to access TS-101. Therefore, when TS-101 is located behind an NAT, it is recommended to use an NAT router with DDNS function to perform DDNS function.
3.4.10 View Network Settings You can view current network settings and status of TS-101 in this section.
3.5 Device Configuration You can configure SATA disk, USB disk, USB printer and external SATA (eSATA) disk in this section. 3.5.1 SATA Disk This page shows the model, size and current status of the SATA disk on TS-101. You can format and check disk, and scan bad blocks on the disk.
3.5.2 USB Disk TS-101 supports USB disks and thumb drives for extended storage and Q-RAID 1 function. You can select one of the following settings for the disk: a. Data Sharing: Select this option to use the selected USB disk as a network share of TS-101. b. Q-RAID 1: Select this option to configure the selected USB disk with the SATA disk in TS-101 as Q-RAID 1 configuration. When backup is executed once, data can be automatically backed up by connecting the external disk to TS-101 directly.
Recover data from USB disk when the SATA disk of TS-101 fails: When the SATA disk of TS-101 fails, you can recover data from a backup disk if the disks have been previously configured as Q-RAID 1. Please follow the steps below to recover data from a backup USB disk to TS-101. 1. Replace the failed SATA disk with a new one. 2. Format the new disk by clicking Format now in Device Configuration-SATA Disk page. 3. Connect a USB disk to TS-101. 4. Go to Device Configuration-USB Disk page.
3.5.3 USB Printer 1. To provide printer sharing function for network users, you can simply connect a USB printer to the USB port of TS-101. TS-101 will detect the printer automatically. 2. A printer icon should be shown in the share folder of the server. Double click the icon.
3. Install the printer driver. 4. When finished, you can start to use network printer service of TS-101. Note: 1. TS-101 supports general USB printer only but not multifunction printer. 2. TS-101 printer service is only supported in Windows OS but not Mac OS. 3. For the information of supported USB printer models, please visit http://www.qnap.com.
3.5.4 eSATA Disk TS-101 supports eSATA disk for extended storage and Q-RAID 1 function. You can connect an eSATA disk to the eSATA port of TS-101. You can select one of the following two settings for the disk: a. Data Sharing: Select this option to use the selected eSATA disk as a network share of TS-101. b. Q-RAID 1: Select this option to configure the selected eSATA disk with the SATA disk in TS-101 as Q-RAID1 configuration.
Recover data from eSATA disk when the SATA disk of TS-101 fails: When the SATA disk of TS-101 fails, you can recover data from a backup disk if the disks have been previously configured as Q-RAID 1. Please follow the steps below to recover data from a backup eSATA disk to TS-101. 1. Replace the failed SATA disk with a new one. 2. Format the new disk by clicking Format now in Device Configuration-SATA Disk page. 3. Connect an eSATA disk to TS-101. 4. Go to Device Configuration- eSATA Disk page.
3.6 User Management The files on TS-101 can be shared among multiple users. For easier management and better control of users’ access right, you have to organize users, user groups and their access right control. 3.6.1 Users The system has created the following users by default: n Administrator By default, administrator has access to system administration and cannot be deleted. o Guest This is a built-in user and will not be displayed on User Management page.
512 users can be created at maximum (including system default users). You can create a new user according to your needs. The following information is required to create a new user: 9 User name The user name must not exceed 32 characters. It is case-insensitive and supports double-byte characters, such as Chinese, Japanese, and Korean except: " / \ [ ] : ; | = , + * ? < >` ' 9 Password The password is case-sensitive and can be 16 characters long at maximum.
3.6.2 User Groups User group is a collection of users with the same access right to files or folders. TS-101 has created the following user groups by default: n Administrators All members in this group have administration right. You cannot delete this group. o Everyone All registered users belong to everyone group. You cannot delete this group. You can manage user groups with the following options: 1024 groups can be created at maximum. A group name must not exceed 256 characters.
Create Users and Assign Users to User Group The following example demonstrates how to create new users and assign users to a user group. ABC Co. has recently recruited two employees Mr. Jones Lee for Administration Department and Ms. Jane Wu for Sales Department. The IT Department therefore needs to create two user accounts for them to access company data on TS-101. i. To create a user account, go to User Management-Users. Click Create. ii. Enter the user name (Jones Lee/ Jane Wu) and password.
iii. Select the user groups the users belong to on the right list, i.e. Mr. Jones Lee for Administration Dept and Ms. Jane Wu for Sales Dept, and click Add. Then click Close. iv. The user names will appear on the list on Create User Page.
Create Private Network Share for User Groups You can create particular network share for each user group. The procedure is described as below: 1. To create a network share called media accessible by Administration Department only, please go to “User Management—User Groups” page. Select the user group Administration Dept and click Create Private Network Share on the right. 2. Enter the network share name media.
3. You can see the folder media in Network Share Management page. 4. Enter Access Control. You can see that only Administration Dept has full access right to the folder.
3.6.3 Quota To allocate disk volume efficiently, you can specify the quota that can be used by each user. When this function is enabled and a user has reached his/her disk quota, he/she cannot upload data to the server anymore. By default, no limitations are set for users. You can modify the following two options: i. Enable quota for all users ii.
2. Select Jones Lee on User page and click Quota Settings on the right. 3. Enter the quota size 2000MB and click OK. 4. Follow the same steps and enter the quota size 4000MB for Jane Wu and click OK. The quota setting is successfully applied.
3.7 Network Share Management The primary purpose of network storage is file sharing. You can create different network share folders for various types of files, and provide different file access rights to users or user groups.
3.7.1 Create To create a network share, enter the following information: 9 Network share name The share name can be 32 characters long at maximum and cannot contain the following characters: ".+=/\:|*?<>;[]% 9 Disk volume This area shows the disk volume status. 9 Path All data is stored under the assigned path onto the disk volume. You can select “Specify path automatically” or assign a path manually. The path cannot exceed 256 characters and cannot contain the characters below: ".
3.7.2 Property To edit the property of an existing network share, select a share and click Property. You can then edit the content of that share.
3.7.3 Access Control When a network share is created, you can assign access rights to users or user groups: 9 Deny access Access to the network share will be denied. 9 Read only Users can read the files only on the network share. 9 Full access Users can read, write, create, or delete files and folders on the network share. 3.7.4 Delete Select a share and click Delete. Click OK to confirm.
3.8 System Tools System Tools enable you to optimize the maintenance and management of TS101.
3.8.1 Alert Notification Enter the e-mail address of the administrator and the IP address of the SMTP server. In case of warning or malfunction, e.g. CPU fan fails, a drive fails or is unplugged, an email will be sent to the administrator automatically. You can go to Event Logs (refer to Chapter 3.9) to check the details of all errors and warnings. If your mailbox requires SMTP authentication, enter the user name and password.
3.8.3 Hardware Settings You can enable or disable the hardware functions of TS-101. i. Enable configuration reset switch By enabling this option, you can press the reset button for 5 seconds to reset the administrator password and system settings to default. Reset Button ii. Enable hard disk standby mode When this function is enabled, hard disk will go to standby mode if there is no access within the specified period.
3.8.4 System Update Note: If the system is running properly, you do not need to update the firmware. Before updating system firmware, please make sure the product model and firmware version are correct. Follow the steps below to update firmware: Step 1: Download the release notes of the same version as the firmware from QNAP website http://www.qnap.com. Read the release notes carefully to make sure you need to upgrade the firmware.
3.8.5 Change Logo You can choose your own picture to display on the login page of TS-101. The size of the picture cannot exceed 20K bytes.
3.8.6 Remote Replication (Disaster Recovery) Remote Replication enables you to replicate files on TS-101 to another TS-101 or QNAP NAS series. The files will be compressed before the replication process in order to save time for data transfer. Make sure a network share is created before creating a remote replication task. Using Remote Replication Login TS-101 and go to Remote Replication in System Tools. i. New a. Click New to enter the following page.
b. Complete all settings and click OK to save or Cancel to quit. c. The port for remote replication is 873. If you are using two TS-101 servers behind an NAT router, please open the port 873 on NAT router and forward the port to the corresponding LAN IP of TS-101. Otherwise, the remote replication service will be blocked by NAT.
ii. Edit a. Select the task to be edited. b. Click Edit. c. Modify the settings. d. Click OK to save or Cancel to quit. iii. Delete a. Select the task to be deleted. b. Click Delete.
3.8.7 • Backup/ Restore/ Reset Settings To backup all settings, including user accounts, server name and network configuration etc., click Backup and select to open or save the setting file. • To restore all settings, click Browse to select a previously saved setting file and click Restore to confirm. • To reset all settings to default, click Reset.
3.8.8 Network Recycle Bin This function enables files deleted on the shares of TS-101 to be removed to Network Recycle Bin to reserve the files temporarily. To enable this function, check the box “Enable Network Recycle Bin” and click Apply. The system will create a network share "Network Recycle Bin" automatically. To delete all the files in network recycle bin, click “Clean Network Recycle Bin”.
3.9 Event Logs TS-101 can store thousands of recent event logs, including warning, error and information messages. In case of system malfunction, event logs can be retrieved to analyze system problems.
Chapter 4 Copy Data Directly by Front USB Port to TS-101 TS-101 supports direct copy of data on USB devices to TS-101 by using the Copy button. To use this function, please follow the steps below: 1. Make sure a SATA disk is installed correctly in TS-101 according to the instructions in Chapter 2.1. 2. Turn on TS-101. 3. Format the SATA disk in SATA Disk page of Device Configuration (refer to Chapter 3.5.1). A system default folder Qusb will be created in TS-101. 4. Connect USB devices, e.g.
* xxxx: year ; yy: month; zz: date Note: USB auto copy function supports only USB device of 10GB storage capacity or less.
Chapter 5 Multimedia Station 5.1 Share Photos and Multimedia Files via Web Interface TS-101 provides a user-friendly web management interface for you to manage personal albums easily. You can view images and multimedia files, or browse photos by thumbnails preview. A. Upload photos by web administration 1. To use Multimedia Station of TS-101, make sure a SATA disk is installed correctly in TS-101 according to the instructions in Chapter 2.1. A share folder Qmultimedia will be created.
2. Click on the link http://TS-101 IP/Qmultimedia on Multimedia Station page or click Multimedia Station on the login page of TS-101 to access Multimedia Station. 3. Click on the top right hand corner. Login with administrator name and password to manage Multimedia Station. Users without administration right can view the photos and multimedia files on Multimedia Station but they do not have the right to modify the files.
4. Click Browse to select the multimedia file and then click Upload to upload the file to the folder. 5. You can also create folders by clicking - 105 - and upload files to the folders.
B. Upload photos to Qmultimedia folder directly You can upload multimedia files to TS-101 directly by the following steps. 1. Use Run function in Windows. Enter \\[server name] or \\[server IP] to access share folder on TS-101. 2. Open the folder Qmultimedia. Enter the user name and password to login. 3. Drag the files and folders to the folder directly. Please wait patiently when TS-101 is generating thumbnails for images during uploading.
When you login Multimedia Station by web browser again, all multimedia files will be shown.
View Photo Information 1. To view detailed information of a photo, click on the thumbnail of the picture. 2. The information of the photo, e.g. file name, resolution, size, camera producer will be shown on the right. You can enter a description for the picture in the box below the photo and click Submit. To reset the description to previously saved version, click Reset.
Buttons Description You can use the buttons on top of the photo to manage the album. Back to previous level Previous image Next image Rotate image anticlockwise Rotate image clockwise Zoom in Zoom out Play slideshow. Select the time interval in seconds. Click play to play slide show. To stop playing, click stop. Print the image Save the picture Play music or video files To play music or video files on Multimedia Station, you can click on the thumbnail of the file displayed on the page.
5.2 Enable iTunes Service Enable iTunes service on TS-101. The mp3 files on Qmultimedia folder of TS-101 will be shared via iTunes. All the computers with iTunes installed on LAN will be able to find, browse and play the music files on TS-101.
Note: You can download the latest iTunes software from official Apple website http://www.apple.com.
5.3 Use UPnP Media Server TS-101 is built-in with TwonkyMedia, DLNA compatible UPnP media server. Enable this function and TS-101 will share particular music, photos or video files to DLNA network. You can use DLNA compatible digital media player (DMP), to play the multimedia files on TS-101 on TV or acoustic sound system. To use UPnP Media Server, please enable this function and click the following link (http://TS-101 IP:9000/) to enter the configuration page of UPnP Media Server.
Click on the link http://TS-101 IP:9000/ to enter UPnP Media Server configuration page and configure the following settings. (1) Language: Select the display language. (2) Server Name: Enter the name of TS-101 UPnP Media Server. This name will be shown on DMP operation interface, e.g. NAS. (3) Content Locations: Select the share folder on TS-101 to be shared to DMP. The default folder is Qmultimedia. You can add more than one share folder. Click Save Changes to save the settings.
About UPnP and DLNA Universal Plug and Play (UPnP) is a set of computer network protocols promulgated by the UPnP Forum. The purpose of UPnP is to allow devices to connect seamlessly and to simplify the implementation of networks at home and in corporate environment. UPnP achieves this by defining and publishing UPnP device control protocols built upon open, Internet-based communication standards.
Chapter 6 Download Station TS-101 supports BT, HTTP, and FTP download mechanisms. You can add download task to TS-101 and let the server finish downloading independent of PC. Warning: Please be warned against illegal downloading of copyrighted materials. The Download Station functionality is provided for downloading authorized files only. Downloading or distribution of unauthorized materials may result in severe civil and criminal penalty.
2. Click on the link http://TS-101 IP/Qdownload on Download Station page or click Download Station on the login page of TS-101 to access Download Station.
3. Select Add new BT task or Add new FTP/HTTP task. (A) Add new BT task Click Add new BT task on the left and upload a torrent file. You can download legal torrent files by searching on the Internet. There are websites that provide legally sharing torrents e.g. www.legaltorrents.com. Please download the torrent files to your local disk and then upload them to TS-101.
(B) Add new FTP/HTTP task To run an FTP download task, click Add new FTP/HTTP task. Enter the FTP URL of the download task and select the share folder to save the files. Enter the user name and password to login the FTP server (if necessary). Then click OK to start downloading. To run an HTTP download task, click Add new FTP/HTTP task. Enter the HTTP URL of the download task and select the share folder to save the files. Then click OK to start downloading. 4.
5. You can select an available download task and click Set Share Time to configure the time for sharing the torrent file, or click Set Config to set the maximum number of downloads at the same time (default value is 3). You can also set the maximum download and upload rate (default value is 0, which means unlimited), and port range (default range is 6881-6899).
6. To pause a running download task, select the task in View Run list and click Pause/ Restart download task. You can view tasks that are paused or finished in View Pause List and View Finish List respectively. To restart a paused task, select the task in View Pause List and click Pause/ Restart download task. 7. You can also increase or decrease task priority by clicking Increase download priority and Decrease download priority when there are multiple download tasks.
8. To delete a running, paused, or finished task, select the task and click Delete download task. You can select to remove the download task only and retain the downloaded files, or remove the task and downloaded files. 9. To logout Download Station, click on the top right hand corner.
10. To access the folders you have downloaded, please go to the share folder Qdownload of TS-101.
Dump Diagnostic Information To view the diagnostic details of a download task, select a task on the list and click [Dump Diagnostic Information].
The common reasons for slow BT download rate or download error are as below: (1) The torrent file has expired, the peers have stopped sharing this file, or there is error in the file. (2) TS-101 has configured to use fixed IP but DNS server is not configured, or DNS server fails. (3) Set the maximum number of simultaneous downloads as 3-5 for the best download rate. (4) TS-101 is located behind NAT router. The port settings have led to slow BT download rate or no response.
Chapter 7 Web Server TS-101 enables you to upload web pages and manage your own website easily by Web Server function. It also supports PHP and SQLite for you to establish an interactive website. Once you activate Web Server function, you can access your own homepage from anywhere. You can add hyperlinks in your homepage to connect to all the features of TS-101, such as Download Station, Multimedia Station and Web Server. 1.
The file index.html, index.htm or index.php will be the home path of your webpage.
3. Click on the link http://TS-101 IP/ on Web Server page or click Web Server on the login page of TS-101 to access the web page you upload. Note that when Web Server is enabled, you have to type [http://TS-101 IP address:6000] in your web browser to access the login page of TS-101.
SQLite Management SQLiteManager is a multilingual web-based tool to manage SQLite databases and can be downloaded from http://www.sqlitemanager.org/. Please follow the steps below or refer to the INSTALL file in the downloaded SQLiteManager-*.tar.gz? to install the SQLiteManager. (1) Unpack your download file SQLiteManager-*.tar.gz. (2) Upload the unpacked folder SQLiteManager-* to \\TS-101 IP\Qweb\. (3) Open your web browser and go to http://TS-101 IP/SQLiteManager-*/.
Chapter 8 FTP Server TS-101 supports FTP service. To use FTP service, enable this function in Network Settings and follow the steps below: 1. Open an IE browser and enter ftp://[TS-101 IP] or ftp://[TS-101 name]. OR 2. By Web File Manager of TS-101. a. Go to TS-101 administration page and click Web File Manager. Enter user name and password to login TS-101.
b. Click FTP. c. Enter the user name and password to login FTP service.
d. You can start to use FTP service.
Chapter 9 Web File Manager Using Web File Manager To use Web File Manager, enable web service in Network Settings first.
Launch the web browser and go to TS-101 administration page. Select Web File Manager and enter the correct login name and password. You can login as “guest” to access the network shares open to guest access on TS-101. The login password of guest is guest. Note: Make sure a network share has been created before using Web File Manager.
Select an existing network share for management. You can organize network share folders of TS-101. With Web File Manager, you can upload, rename, or delete files and folders in the network shares. View files online Click on a file displayed on the web page. The information of the file will be displayed. If your browser does not support the file format, a download window will pop up automatically. Download the file and you can open it on your PC. Create folder i.
Rename file or folder i. Select a file or folder to rename. ii. Click iii. Enter the new file or folder name and click OK. (Rename) on the toolbar. Delete file or folder i. Select a file or folder to delete. ii. Click iii. Confirm to delete the file or folder. (Delete) on the toolbar. To delete all files and folders, click (Select All) and Upload file i. Open the folder to upload file to. ii. Click Browse to select the file. iii. Click Upload. Download file i.
View Files Named in Local Language To view files named in Chinese, you may have to configure the browser settings. Take Internet Explorer as an example, follow the steps below to configure the settings. 1. Click on Tools in IE browser. 2. Click Internet Options. 3. Cancel this option. 4. Click OK. 5. Restart the browser.
Web File Manager Icons Icon Description Return to the parent folder Refresh the current page Return to network share list home page Create folder Rename file or folder Delete file or folder Select all Cancel selection Logout Full access network share folder Read-only network share folder Malfunction network share folder - 137 -
Chapter 10 NetBak Replicator NetBak Replicator is a powerful program installed in user’s system (Windows® OS only) for data backup. You can back up any files or folders on local PC to specified share folder on TS-101 by LAN or WAN. Main Functions 1. Backup • Instant Backup You can select files and folders on local PC and back up files to specified network share folder on TS-101 immediately. • File Filter You can select particular file types to be excluded from backup.
Install NetBak Replicator 1. Select Install NetBak Replicator in TS-101 CD-ROM. 2. Follow the steps to install NetBak Replicator. 3. Upon successful installation, a shortcut icon will be shown on the Desktop. Double click the icon to run NetBak Replicator.
Use NetBak Replicator 1. Before using NetBak Replicator, please login TS-101 administration and go to Network Share Management to create a share folder for backup. Make sure the share folder is open for everyone access or you login the share folder with an authorized account or administrator by NetBak Replicator.
2. Run NetBak Replicator. Click . All TS-101 and their share folders within the network will be displayed.
3. When the following window appears, all TS-101 in the LAN will appear on the left list. Select a server and a share folder on the right. NetBak Replicator also supports backup via WAN, you can enter the IP address of TS-101 for data backup directly and select a share folder. Then click OK. 4. Enter the user name and password to login the server. 5. You can start the backup procedure upon successful connection to the TS-101.
Description of Buttons on NetBak Replicator Open Configuration: Open a previously saved NetBak Replicator configuration. Save Configuration: Save the settings on NetBak Replicator. The file will be named as *.rpr Select All: Select all items in the window. Clear All: Clear selection. Select My Document: Select all folders in My Document.
• Backup Select files and folders for backup.
9 Start When you have selected the files for backup to TS-101, click Start on NetBak Replicator. The program will start to copy the selected files to the specified share folder on TS-101.
9 File Filter Click File Filter on NetBak Replicator main page to select file format to be skipped from backup. Then click OK.
9 Schedule Click Schedule on NetBak Replicator main page. Then check the box “Enable Backup Schedule” and select the frequency and time for backup. Click OK to confirm.
9 Monitor Select a folder for monitoring. When this option is enabled, the system will upload all files or folders to the server instantly for backup when the files or folders are modified. Other files will be gray and cannot be selected. Click Monitor again to cancel monitoring. An icon ® appear on task bar of Windows when monitoring is in process.
9 Initialize Configuration When using this function, NetBak Replicator will record all current settings of the user, including whether or not monitor function is enabled. When the user login again, this program will load the previous recorded settings for users to manage data backup.
• Restore Please follow the steps below to restore files from TS-101 to your PC. a. Restore to original position: Select the location that the data will be restored to. b. Select new restore position: Click to select the directory to restore data to or select a previously chosen location from the drop-down menu. c. Select the folder(s) and sub-folder(s) for restoring data on the right list and click Start.
d. Option: Select recovery option and error option.
• Log a. Save As…: To save all logs on NetBak Replicator, click this button. All logs will be saved as text file. b. Clear All: Click this button to clear all logs. c. Option: Select the type of logs to be recorded― “Record all logs” or “Record error logs only”.
Chapter 11 TS-101 Maintenance This section provides a general overview on system maintenance. 11.1 Restart/ Shut down Server Follow the steps below to restart or shut down TS-101. 1. Enter the administration page and select Restart/ Shutdown in System Tools. 2. Click Restart to reboot the server or Shut Down to turn off the server.
11.2 Reset Administrator Password and Network Settings To reset the administrator password and network settings of TS-101, 1. Press the reset button of TS-101 for a few seconds. A beep sound will be heard. 2. Login TS-101 with the default user name and password: Default user name: administrator Password: admin Note: To reset the system by the reset button, the option “Enable configuration reset switch” in Hardware Settings must be activated.
11.3 Disk Failure or Malfunction When you encounter disk malfunction or failure, please do the following: 1. Record the malfunction status or error messages shown in Event Logs. 2. Stop using the failed TS-101 and turn off the server. 3. Contact customer service for technical support. Note: TS-101 must be repaired by professional technicians, do not try to repair the server yourself. Please back up any important files or folders to avoid potential data loss due to disk crash. 11.
Technical Support QNAP provides dedicated online support and customer service via instant messenger. You can contact us by the following means: Online Support: http://www.qnap.com E-mail: support@qnap.com.tw MSN: support@qnap.com.
GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary.
or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on
this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.
8. If the distribution and/or use of the Program are restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9.
CORRECTION. 12.
