Installation Guide

ManualsBrandsQmark ManualsBaseboard HeatersDouble Pole Thermostat for HBB/Commercial Baseboard Heaters

WARNING

Thermostats

For Use on “D” Series Commercial and

Electric/Hydronic Baseboard Heaters

Dear Owner,

Congratulations! Thank you for purchasing this new product manufactured by a division of Marley

Engineered Products. You have made a wise investment selecting the highest quality product in the heat-

ing industry. Please carefully read and follow the installation and maintenance directions shown in this

manual. You should enjoy years of efficient heating comfort with this product from Marley Engineered

Products... the industry’s leader in design, manufacturing, quality and service.

... The Employees of

Marley Engineered Products

Installation & Maintenance Instructions

T1 & T2 T1TPH & T2TPH

FILE #E37116

SAVE THESE INSTRUCTIONS

2. THE INSTALLATION MUST COMPLY WITH APPLICABLE

LOCAL AND NATIONAL ELECTRIC CODES AND UTILITY

REQUIREMENTS.

3. REFER TO INSTALLATION INSTRUCTIONS PROVIDED

WITH THE HEATER WHEN INSTALLING THESE ACCES-

SORIES.

4. CHECK ACCESSORY AND HEATER NAMEPLATE TO VERI-

FY POWER REQUIREMENTS MATCH POWER SUPPLY

COMING TO HEATER AND ACCESSORY. MAKE SURE

TOTAL POWER REQUIREMENTS DO NOT EXCEED RAT-

INGS OF ACCESSORY.

Read Carefully - This instruction sheet contains vital infor-

mation for the proper installation, and use of this device.

Failure to follow these instructions could result in severe

bodily harm or property damage. Keep this manual for

future reference.

1. BE SURE ELECTRIC POWER IS DISCONNECTED AT MAIN

FUSE OR CIRCUIT BREAKER DISTRIBUTION PANEL

BEFORE INSTALLATION OR SERVICING AND ALLOW

HEATER TO COOL.

Summary of content (8 pages)

PAGE 1
T1 & T2 Thermostats For Use on “D” Series Commercial and Electric/Hydronic Baseboard Heaters T1TPH & T2TPH FILE #E37116 Installation & Maintenance Instructions Dear Owner, Congratulations! Thank you for purchasing this new product manufactured by a division of Marley Engineered Products. You have made a wise investment selecting the highest quality product in the heating industry. Please carefully read and follow the installation and maintenance directions shown in this manual.
PAGE 2
NOTE: It is recommended that no more than one thermostat be used in each room (area). Table 2 Minimum AWG Wire Size (Copper) Circuit Breaker or Fuse Size 0 thru 12 #14 15 Amp 12.1 thru 16 #12 20 Amp 16.1 thru 24 #10 30 Amp Total Amps INSTALLATION 1. The thermostat can be installed in either end of the heater that the power wiring is brought into. 2. Remove selected junction box end cap (Figure 1) and discard; save screw. JUNCTION BOX 4.
PAGE 3
OPERATION CHECK 1. After your electric baseboard heating system has been completely installed, all thermostats, whether mounted on the wall or in the baseboard, should be turned to “LOW” or “OFF”. Then turn on breakers or install fuses. Wait 3 to 5 minutes and check to see that none of the heaters are operating. Should any of the heaters be operating, disconnect power and check your wiring. If none are operating, then turn the thermostats to the highest position and wait another 3 to 5 minutes.
PAGE 4
LIMITED WARRANTY All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of installation. This warranty does not apply to damage from accident, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate voltage; nor to equipment improperly installed or wired or maintained in violation of the product’s installation instructions.
PAGE 5
T1 & T2 Thermostats T1TPH & T2TPH Homologué U.L. et C-UL Dossier E37116 Pour Série « D » et à Caloporteur Liquide Instructions d’installation Cher utilisateur, Félicitations ! Nous vous remercions d'avoir fait l'acquisition de ce nouveau produit fabriqué par une division de Marley Engineered Products. Vous avez fait un bon investissement en choisissant un appareil de qualité imbattable.
PAGE 6
Table 2 NOTE: Il n’est pas recommandé d’utiliser plus d’un thermostat par piece (ou par zone). INSTALLATION 1. On peut installer le thermostat à l’une ou l’autre des extrémités du radiateur où est effectué le branchement. 2. Enlevez le couvercle latéral de la boîte de jonction choisie (voir la figure 1) et mettez-le au rebut. Conservez la vis.
PAGE 7
VÉRIFICATION DU FONCTIONNEMENT 1. Une fois tous les radiateurs installés, réglez tous les thermostats (muraux ou intégrés au radiateur) à la position Bas ou Arrêt. Placez les disjoncteurs à la position Marche ou posez les fusibles. Attendez 3 à 5 min pour vous assurer qu’aucun radiateur n’est sous tension. Si un radiateur est sous tension, coupez l’alimentation et vérifiez les connexions. Si aucun radiateur n’est sous tension, réglez les thermostats au maximum et attendez 3 à 5 min.
PAGE 8
GARANTIE LIMITÉE Tous les produits mentionnés dans la présente notice sont garantis contre tout vice de matière et de construction pour une durée d'une année à partir de la date de montage.