User`s guide
Table Of Contents
- Table of Contents
- Section1 Introduction
- Section2 Using SANbox Manager
- 2.1 Installing SANbox Manager
- 2.1.1 SANsurfer Management Suite Disk - Windows Installation
- 2.1.2 SANsurfer Management Suite Disk - Linux Installation
- 2.1.3 SANsurfer Management Suite Disk - Solaris Installation
- 2.1.4 SANbox2 Installation Disk - Windows Installation
- 2.1.5 SANbox2 Installation Disk - Linux Installation
- 2.1.6 SANbox2 Installation Disk - Solaris Installation
- 2.2 Starting SANbox Manager
- 2.3 Exiting SANbox Manager
- 2.4 Uninstalling SANbox Manager
- 2.5 Changing Default File Password
- 2.6 Setting Preferences
- 2.7 Using Online Help
- 2.8 Viewing Software Version and Copyright Information
- 2.9 SANbox Manager User Interface
- 2.10 Using the Topology Display
- 2.11 Using the Faceplate Display
- 2.1 Installing SANbox Manager
- Section3 Managing Fabrics
- 3.1 Security
- 3.2 Managing the Fabric Database
- 3.3 Replacing a Failed Switch
- 3.4 Displaying Fabric Information
- 3.5 Zoning a Fabric
- Section4 Managing Switches
- 4.1 Displaying Switch Information
- 4.2 Managing Alarms
- 4.3 Exporting Name Server Information to a File
- 4.4 Paging a Switch
- 4.5 Setting the Date and Time
- 4.6 Setting Temperature Thresholds
- 4.7 Resetting a Switch
- 4.8 Configuring a Switch
- 4.9 Archiving a Switch
- 4.10 Restoring a Switch
- 4.11 Managing Firmware
- 4.12 Restoring the Factory Default Configuration
- Section5 Managing Ports
- AppendixA Command Line Interface
- A.1 Logging On to a Switch
- A.2 Command Syntax
- A.3 Commands
- Admin Command
- Alias Command
- Config Command
- Date Command
- Fallback Command
- Help Command
- History Command
- Image Command
- Lip Command
- Passwd Command
- Ps Command
- Quit Command
- Reset Command
- Set Command
- Set Config Command
- Set Log Command
- Set Port Command
- Set Setup Command
- Show Command
- Show Config Command
- Show Log Command
- Show Perf Command
- Show Setup Command
- Shutdown Command
- Test Command
- Uptime Command
- User Command
- Whoami Command
- Zone Command
- Zoneset Command
- Zoning Command
- AppendixB Graphing Port Performance
- AppendixC Messages
- C.1 Fabrics File—Open, Save
- C.2 Add a Fabric
- C.3 Network Properties Dialog
- C.4 Switch Properties Dialog
- C.5 Port Properties Dialog
- C.6 Faceplate Display
- C.7 Firmware Fallback Dialog
- C.8 Load Firmware Dialog
- C.9 Port Loopback Test Dialog
- C.10 Extended Credits Dialog
- C.11 Zoning Dialog
- C.12 Restore Configuration Dialog
- C.13 Save Fabric View
- C.14 Trap Configuration Dialog
- Glossary
- Index

5 – Managing Ports
Displaying Port Information
5-6 59022-05 A
Class 3 Toss Count Number of class 2 and class 3 sequences that were discarded
by this port. A sequence can be discarded because of
detection of a missing frame (based on SEQ_CNT), detection
of an E_D_TOV timeout, receiving a reject frame, receiving
frames for a stopped sequence, or other causes.
FReject Count Number of frames, from devices, that have been rejected.
Frames can be rejected for any of a large number of reasons.
FBusy Count Number of class 2 and class 3 fabric busy (F_BSY) frames
generated by this port in response to incoming frames. This
usually indicates a busy condition on the fabric or N_port that
is preventing delivery of this frame.
Link Failures Number of optical link failures detected by this port. A link
failure is a loss of synchronization for a period of time greater
than the value of R_T_TOV or by loss of signal while not in the
offline state. A loss of signal causes the switch to attempt to
re-establish the link. If the link is not re-established by the time
specified by R_T_TOV, a link failure is counted. A link reset is
performed after a link failure.
Primitive Sequence
Errors
Number of bad primitives received by the port.
Rx Link Resets Number of link reset primatives received from an attached
device.
Tx Link Resets Number of link reset primatives sent from this port to an
attached port.
Rx Offline Sequences Number of offline sequence primitives received by the port.
Tx Offline Sequences Number of offline primitives transmitted by the port.
Total Errors Total number of primitive and non-primitive port link errors.
Total Tx Frames Total number of frames transmitted by the port.
Total Rx Frames Total number of frames received by the port.
Total Tx Words Total number of words transmitted by the port.
Total Rx Words Total number of words received by the port.
Total Link Resets Number of link-reset primitives the transmitted by the port.
Total Offline
Sequences
Total number of offline sequences transmitted and received by
the port.
Table 5-5 Port Statistics Data Window Entries (Continued)
Entry Description