User`s guide
Table Of Contents
- Table of Contents
- Section1 Introduction
- Section2 Using SANbox Manager
- 2.1 Installing SANbox Manager
- 2.1.1 SANsurfer Management Suite Disk - Windows Installation
- 2.1.2 SANsurfer Management Suite Disk - Linux Installation
- 2.1.3 SANsurfer Management Suite Disk - Solaris Installation
- 2.1.4 SANbox2 Installation Disk - Windows Installation
- 2.1.5 SANbox2 Installation Disk - Linux Installation
- 2.1.6 SANbox2 Installation Disk - Solaris Installation
- 2.2 Starting SANbox Manager
- 2.3 Exiting SANbox Manager
- 2.4 Uninstalling SANbox Manager
- 2.5 Changing Default File Password
- 2.6 Setting Preferences
- 2.7 Using Online Help
- 2.8 Viewing Software Version and Copyright Information
- 2.9 SANbox Manager User Interface
- 2.10 Using the Topology Display
- 2.11 Using the Faceplate Display
- 2.1 Installing SANbox Manager
- Section3 Managing Fabrics
- 3.1 Security
- 3.2 Managing the Fabric Database
- 3.3 Replacing a Failed Switch
- 3.4 Displaying Fabric Information
- 3.5 Zoning a Fabric
- Section4 Managing Switches
- 4.1 Displaying Switch Information
- 4.2 Managing Alarms
- 4.3 Exporting Name Server Information to a File
- 4.4 Paging a Switch
- 4.5 Setting the Date and Time
- 4.6 Setting Temperature Thresholds
- 4.7 Resetting a Switch
- 4.8 Configuring a Switch
- 4.9 Archiving a Switch
- 4.10 Restoring a Switch
- 4.11 Managing Firmware
- 4.12 Restoring the Factory Default Configuration
- Section5 Managing Ports
- AppendixA Command Line Interface
- A.1 Logging On to a Switch
- A.2 Command Syntax
- A.3 Commands
- Admin Command
- Alias Command
- Config Command
- Date Command
- Fallback Command
- Help Command
- History Command
- Image Command
- Lip Command
- Passwd Command
- Ps Command
- Quit Command
- Reset Command
- Set Command
- Set Config Command
- Set Log Command
- Set Port Command
- Set Setup Command
- Show Command
- Show Config Command
- Show Log Command
- Show Perf Command
- Show Setup Command
- Shutdown Command
- Test Command
- Uptime Command
- User Command
- Whoami Command
- Zone Command
- Zoneset Command
- Zoning Command
- AppendixB Graphing Port Performance
- AppendixC Messages
- C.1 Fabrics FileāOpen, Save
- C.2 Add a Fabric
- C.3 Network Properties Dialog
- C.4 Switch Properties Dialog
- C.5 Port Properties Dialog
- C.6 Faceplate Display
- C.7 Firmware Fallback Dialog
- C.8 Load Firmware Dialog
- C.9 Port Loopback Test Dialog
- C.10 Extended Credits Dialog
- C.11 Zoning Dialog
- C.12 Restore Configuration Dialog
- C.13 Save Fabric View
- C.14 Trap Configuration Dialog
- Glossary
- Index

59022-05 A Page iii
Table of Contents
Section 1 Introduction
1.1 Intended Audience ............................................................................................. 1-1
1.2 Related Materials ............................................................................................... 1-1
1.3 Technical Support............................................................................................... 1-2
1.3.1 Availability.................................................................................................. 1-2
1.3.2 Training...................................................................................................... 1-2
1.3.3 Contact Information ................................................................................... 1-2
Section 2 Using SANbox Manager
2.1 Installing SANbox Manager................................................................................ 2-1
2.1.1 SANsurfer Management Suite Disk - Windows Installation....................... 2-2
2.1.2 SANsurfer Management Suite Disk - Linux Installation.............................2-3
2.1.3 SANsurfer Management Suite Disk - Solaris Installation .......................... 2-4
2.1.4 SANbox2 Installation Disk - Windows Installation ..................................... 2-5
2.1.5 SANbox2 Installation Disk - Linux Installation ........................................... 2-5
2.1.6 SANbox2 Installation Disk - Solaris Installation......................................... 2-5
2.2 Starting SANbox Manager.................................................................................. 2-6
2.3 Exiting SANbox Manager ................................................................................... 2-8
2.4 Uninstalling SANbox Manager ........................................................................... 2-9
2.5 Changing Default File Password...................................................................... 2-10
2.6 Setting Preferences.......................................................................................... 2-10
2.7 Using Online Help ............................................................................................ 2-11
2.8 Viewing Software Version and Copyright Information ...................................... 2-11
2.9 SANbox Manager User Interface .....................................................................2-12
2.9.1 Menu Bar................................................................................................. 2-13
2.9.2 Tool Bar ................................................................................................... 2-14
2.9.3 Fabric Tree .............................................................................................. 2-15
2.9.4 Graphic Window ...................................................................................... 2-16
2.9.5 Data Window and Tabs............................................................................2-16
2.9.6 Working Status Indicator.......................................................................... 2-16
2.10 Using the Topology Display.............................................................................. 2-17
2.10.1 Switch and Link Status ............................................................................ 2-17
2.10.2 Working with Switches and Links ............................................................ 2-18
2.10.2.1 Selecting Switches and Links ......................................................... 2-18
2.10.2.2 Arranging Switches in the Display .................................................. 2-18
2.10.2.3 Opening the Faceplate Display and Popup Menus ........................2-18