User`s guide
Table Of Contents
- Table of Contents
- Section1 Introduction
- Section2 Using SANbox Manager
- 2.1 Installing SANbox Manager
- 2.1.1 SANsurfer Management Suite Disk - Windows Installation
- 2.1.2 SANsurfer Management Suite Disk - Linux Installation
- 2.1.3 SANsurfer Management Suite Disk - Solaris Installation
- 2.1.4 SANbox2 Installation Disk - Windows Installation
- 2.1.5 SANbox2 Installation Disk - Linux Installation
- 2.1.6 SANbox2 Installation Disk - Solaris Installation
- 2.2 Starting SANbox Manager
- 2.3 Exiting SANbox Manager
- 2.4 Uninstalling SANbox Manager
- 2.5 Changing Default File Password
- 2.6 Setting Preferences
- 2.7 Using Online Help
- 2.8 Viewing Software Version and Copyright Information
- 2.9 SANbox Manager User Interface
- 2.10 Using the Topology Display
- 2.11 Using the Faceplate Display
- 2.1 Installing SANbox Manager
- Section3 Managing Fabrics
- 3.1 Security
- 3.2 Managing the Fabric Database
- 3.3 Replacing a Failed Switch
- 3.4 Displaying Fabric Information
- 3.5 Zoning a Fabric
- Section4 Managing Switches
- 4.1 Displaying Switch Information
- 4.2 Managing Alarms
- 4.3 Exporting Name Server Information to a File
- 4.4 Paging a Switch
- 4.5 Setting the Date and Time
- 4.6 Setting Temperature Thresholds
- 4.7 Resetting a Switch
- 4.8 Configuring a Switch
- 4.9 Archiving a Switch
- 4.10 Restoring a Switch
- 4.11 Managing Firmware
- 4.12 Restoring the Factory Default Configuration
- Section5 Managing Ports
- AppendixA Command Line Interface
- A.1 Logging On to a Switch
- A.2 Command Syntax
- A.3 Commands
- Admin Command
- Alias Command
- Config Command
- Date Command
- Fallback Command
- Help Command
- History Command
- Image Command
- Lip Command
- Passwd Command
- Ps Command
- Quit Command
- Reset Command
- Set Command
- Set Config Command
- Set Log Command
- Set Port Command
- Set Setup Command
- Show Command
- Show Config Command
- Show Log Command
- Show Perf Command
- Show Setup Command
- Shutdown Command
- Test Command
- Uptime Command
- User Command
- Whoami Command
- Zone Command
- Zoneset Command
- Zoning Command
- AppendixB Graphing Port Performance
- AppendixC Messages
- C.1 Fabrics File—Open, Save
- C.2 Add a Fabric
- C.3 Network Properties Dialog
- C.4 Switch Properties Dialog
- C.5 Port Properties Dialog
- C.6 Faceplate Display
- C.7 Firmware Fallback Dialog
- C.8 Load Firmware Dialog
- C.9 Port Loopback Test Dialog
- C.10 Extended Credits Dialog
- C.11 Zoning Dialog
- C.12 Restore Configuration Dialog
- C.13 Save Fabric View
- C.14 Trap Configuration Dialog
- Glossary
- Index
2 – Using SANbox Manager
SANbox Manager User Interface
59022-05 A 2-13
2.9.1
Menu Bar
The Menu Bar presents the SANbox Manager menus as shown in Figure 2-8. The
menus and the tasks offered in them vary depending on the display. For example,
the Port menu and many of the Switch menu selections, shown in gray, appear
only in the faceplate display.
Figure 2-8 SANbox Manager Menu Structure
Some menu selections have shortcut keys as shown in Table 2-2.
Delete
Export Name Server
Switch Properties...
Network Properties...
Archive...
Restore...
Load Firmware...
Firmware Fallback...
Set Date/Time...
Temperature Thresholds...
Toggle Beacon
Export Alarm Log...
Configure Alarm Thresholds...
Reset Switch
Restore Factory Defaults
Refresh
Layout Topology
Toggle Auto Layout
Remember Layout
View Port Modes
View Port States
View Port Speeds
View Port Media
Fabric
Add Fabric...
Remove Fabric
Rediscover Fabric
Start Fabric View
View
Zoning
File
Open View File...
Save View As...
Change Default File Password...
Preferences...
Exit
Help
Help Topics
About...
Edit Zoning...
Edit Zoning Config...
Activate Zone Set...
Deactivate Zone Set
Restore Default Zoning
Switch
Port
Port Properties...
Extended Credits...
Reset Port
Port Loopback Test...