User`s guide
Table Of Contents
- Table of Contents
- Section1 Introduction
- Section2 Using SANbox Manager
- 2.1 Installing SANbox Manager
- 2.1.1 SANsurfer Management Suite Disk - Windows Installation
- 2.1.2 SANsurfer Management Suite Disk - Linux Installation
- 2.1.3 SANsurfer Management Suite Disk - Solaris Installation
- 2.1.4 SANbox2 Installation Disk - Windows Installation
- 2.1.5 SANbox2 Installation Disk - Linux Installation
- 2.1.6 SANbox2 Installation Disk - Solaris Installation
- 2.2 Starting SANbox Manager
- 2.3 Exiting SANbox Manager
- 2.4 Uninstalling SANbox Manager
- 2.5 Changing Default File Password
- 2.6 Setting Preferences
- 2.7 Using Online Help
- 2.8 Viewing Software Version and Copyright Information
- 2.9 SANbox Manager User Interface
- 2.10 Using the Topology Display
- 2.11 Using the Faceplate Display
- 2.1 Installing SANbox Manager
- Section3 Managing Fabrics
- 3.1 Security
- 3.2 Managing the Fabric Database
- 3.3 Replacing a Failed Switch
- 3.4 Displaying Fabric Information
- 3.5 Zoning a Fabric
- Section4 Managing Switches
- 4.1 Displaying Switch Information
- 4.2 Managing Alarms
- 4.3 Exporting Name Server Information to a File
- 4.4 Paging a Switch
- 4.5 Setting the Date and Time
- 4.6 Setting Temperature Thresholds
- 4.7 Resetting a Switch
- 4.8 Configuring a Switch
- 4.9 Archiving a Switch
- 4.10 Restoring a Switch
- 4.11 Managing Firmware
- 4.12 Restoring the Factory Default Configuration
- Section5 Managing Ports
- AppendixA Command Line Interface
- A.1 Logging On to a Switch
- A.2 Command Syntax
- A.3 Commands
- Admin Command
- Alias Command
- Config Command
- Date Command
- Fallback Command
- Help Command
- History Command
- Image Command
- Lip Command
- Passwd Command
- Ps Command
- Quit Command
- Reset Command
- Set Command
- Set Config Command
- Set Log Command
- Set Port Command
- Set Setup Command
- Show Command
- Show Config Command
- Show Log Command
- Show Perf Command
- Show Setup Command
- Shutdown Command
- Test Command
- Uptime Command
- User Command
- Whoami Command
- Zone Command
- Zoneset Command
- Zoning Command
- AppendixB Graphing Port Performance
- AppendixC Messages
- C.1 Fabrics File—Open, Save
- C.2 Add a Fabric
- C.3 Network Properties Dialog
- C.4 Switch Properties Dialog
- C.5 Port Properties Dialog
- C.6 Faceplate Display
- C.7 Firmware Fallback Dialog
- C.8 Load Firmware Dialog
- C.9 Port Loopback Test Dialog
- C.10 Extended Credits Dialog
- C.11 Zoning Dialog
- C.12 Restore Configuration Dialog
- C.13 Save Fabric View
- C.14 Trap Configuration Dialog
- Glossary
- Index
59022-05 A Index-3
SANbox2-8c/16 Switch Management
User’s Guide
H
hardware status 4-3
Heartbeat LED 4-3
help 2-11
Help command A-11
History command A-12
I
I/O Stream Guard 5-11
Image command A-13
inband management 3-2, 4-15
initiator device 5-11
Input Power LED 4-3
internal test 5-14, A-65
inter-switch link 3-2
IP
address 4-18
configuration 4-18
ISL monitoring 4-9
L
link
delete 3-6
selecting 2-18
state database A-43
status 2-17
Link data window 4-6
Lip command A-14
log
archive A-33
clear A-33
event A-33
power-on self test A-46
logged in users A-47
Logged-In LED 4-14
login
limit 2-8, 3-3, A-1
monitoring 4-9
logout monitoring 4-9
loop port
bypass A-36
enable A-36
fabric 5-10
generic 5-2, 5-10
initialize A-14
translated 5-10
loopback test 5-14
loss of signal monitoring 4-9
M
maintenance mode 4-23
management workstation 2-1
manufacturer information A-61
media status 5-4
memory
activity A-43
requirement 2-1
menu structure 2-13
messages C-1
N
name server
display A-43
export to file 4-11
zone 3-11
Name Server data window 4-3, 5-8
network
configuration reset A-18
interfaces A-43
properties 4-17
node-to-node test 5-14
O
online
help 2-11
test 5-14, A-65
operating systems 2-1
orphan zone set 3-20
Over Temperature LED 4-3
P
page break A-23
Passwd command A-15
password 3-1
change A-15
fabric view file 2-6, 2-10