User`s guide
Table Of Contents
- Table of Contents
- Section1 Introduction
- Section2 Using SANbox Manager
- 2.1 Installing SANbox Manager
- 2.1.1 SANsurfer Management Suite Disk - Windows Installation
- 2.1.2 SANsurfer Management Suite Disk - Linux Installation
- 2.1.3 SANsurfer Management Suite Disk - Solaris Installation
- 2.1.4 SANbox2 Installation Disk - Windows Installation
- 2.1.5 SANbox2 Installation Disk - Linux Installation
- 2.1.6 SANbox2 Installation Disk - Solaris Installation
- 2.2 Starting SANbox Manager
- 2.3 Exiting SANbox Manager
- 2.4 Uninstalling SANbox Manager
- 2.5 Changing Default File Password
- 2.6 Setting Preferences
- 2.7 Using Online Help
- 2.8 Viewing Software Version and Copyright Information
- 2.9 SANbox Manager User Interface
- 2.10 Using the Topology Display
- 2.11 Using the Faceplate Display
- 2.1 Installing SANbox Manager
- Section3 Managing Fabrics
- 3.1 Security
- 3.2 Managing the Fabric Database
- 3.3 Replacing a Failed Switch
- 3.4 Displaying Fabric Information
- 3.5 Zoning a Fabric
- Section4 Managing Switches
- 4.1 Displaying Switch Information
- 4.2 Managing Alarms
- 4.3 Exporting Name Server Information to a File
- 4.4 Paging a Switch
- 4.5 Setting the Date and Time
- 4.6 Setting Temperature Thresholds
- 4.7 Resetting a Switch
- 4.8 Configuring a Switch
- 4.9 Archiving a Switch
- 4.10 Restoring a Switch
- 4.11 Managing Firmware
- 4.12 Restoring the Factory Default Configuration
- Section5 Managing Ports
- AppendixA Command Line Interface
- A.1 Logging On to a Switch
- A.2 Command Syntax
- A.3 Commands
- Admin Command
- Alias Command
- Config Command
- Date Command
- Fallback Command
- Help Command
- History Command
- Image Command
- Lip Command
- Passwd Command
- Ps Command
- Quit Command
- Reset Command
- Set Command
- Set Config Command
- Set Log Command
- Set Port Command
- Set Setup Command
- Show Command
- Show Config Command
- Show Log Command
- Show Perf Command
- Show Setup Command
- Shutdown Command
- Test Command
- Uptime Command
- User Command
- Whoami Command
- Zone Command
- Zoneset Command
- Zoning Command
- AppendixB Graphing Port Performance
- AppendixC Messages
- C.1 Fabrics File—Open, Save
- C.2 Add a Fabric
- C.3 Network Properties Dialog
- C.4 Switch Properties Dialog
- C.5 Port Properties Dialog
- C.6 Faceplate Display
- C.7 Firmware Fallback Dialog
- C.8 Load Firmware Dialog
- C.9 Port Loopback Test Dialog
- C.10 Extended Credits Dialog
- C.11 Zoning Dialog
- C.12 Restore Configuration Dialog
- C.13 Save Fabric View
- C.14 Trap Configuration Dialog
- Glossary
- Index
C – Messages
Port Loopback Test Dialog
C-16 59022-05 A
Switch is currently unreachable. Unable to
accurately report status of port test.
The application lost communications with
the switch while the switch was running
the loopback tests, and could not
determine whether the tests completed. If
the problem was temporary, restart the
loopback tests.
The port selected for online port test must
be online with active login.
Verify that the port is online with an active
login before starting the loopback test.
Timed out on response notifications. Test
terminated.
The application lost communications with
the switch while the switch was running
the loopback tests, and could not
determine whether the tests completed. If
the problem was temporary, restart the
loopback tests.
Unable to perform loopback test on port ...
■ because port is not in diagnostic state.
■ because port is a donor port.
■ because there is already a port test in
progress.
■ because there is already a port test in
progress.
Correct the error indicated, and retry the
loopback test.
Table C-9. Port Loopback Test Dialog Messages
Message User Action