User`s guide
Table Of Contents
- Table of Contents
- Section1 Introduction
- Section2 Using SANbox Manager
- 2.1 Installing SANbox Manager
- 2.1.1 SANsurfer Management Suite Disk - Windows Installation
- 2.1.2 SANsurfer Management Suite Disk - Linux Installation
- 2.1.3 SANsurfer Management Suite Disk - Solaris Installation
- 2.1.4 SANbox2 Installation Disk - Windows Installation
- 2.1.5 SANbox2 Installation Disk - Linux Installation
- 2.1.6 SANbox2 Installation Disk - Solaris Installation
- 2.2 Starting SANbox Manager
- 2.3 Exiting SANbox Manager
- 2.4 Uninstalling SANbox Manager
- 2.5 Changing Default File Password
- 2.6 Setting Preferences
- 2.7 Using Online Help
- 2.8 Viewing Software Version and Copyright Information
- 2.9 SANbox Manager User Interface
- 2.10 Using the Topology Display
- 2.11 Using the Faceplate Display
- 2.1 Installing SANbox Manager
- Section3 Managing Fabrics
- 3.1 Security
- 3.2 Managing the Fabric Database
- 3.3 Replacing a Failed Switch
- 3.4 Displaying Fabric Information
- 3.5 Zoning a Fabric
- Section4 Managing Switches
- 4.1 Displaying Switch Information
- 4.2 Managing Alarms
- 4.3 Exporting Name Server Information to a File
- 4.4 Paging a Switch
- 4.5 Setting the Date and Time
- 4.6 Setting Temperature Thresholds
- 4.7 Resetting a Switch
- 4.8 Configuring a Switch
- 4.9 Archiving a Switch
- 4.10 Restoring a Switch
- 4.11 Managing Firmware
- 4.12 Restoring the Factory Default Configuration
- Section5 Managing Ports
- AppendixA Command Line Interface
- A.1 Logging On to a Switch
- A.2 Command Syntax
- A.3 Commands
- Admin Command
- Alias Command
- Config Command
- Date Command
- Fallback Command
- Help Command
- History Command
- Image Command
- Lip Command
- Passwd Command
- Ps Command
- Quit Command
- Reset Command
- Set Command
- Set Config Command
- Set Log Command
- Set Port Command
- Set Setup Command
- Show Command
- Show Config Command
- Show Log Command
- Show Perf Command
- Show Setup Command
- Shutdown Command
- Test Command
- Uptime Command
- User Command
- Whoami Command
- Zone Command
- Zoneset Command
- Zoning Command
- AppendixB Graphing Port Performance
- AppendixC Messages
- C.1 Fabrics File—Open, Save
- C.2 Add a Fabric
- C.3 Network Properties Dialog
- C.4 Switch Properties Dialog
- C.5 Port Properties Dialog
- C.6 Faceplate Display
- C.7 Firmware Fallback Dialog
- C.8 Load Firmware Dialog
- C.9 Port Loopback Test Dialog
- C.10 Extended Credits Dialog
- C.11 Zoning Dialog
- C.12 Restore Configuration Dialog
- C.13 Save Fabric View
- C.14 Trap Configuration Dialog
- Glossary
- Index

A – Command Line Interface
Show Command
59022-05 A A-45
LIPF7F7 A loop initialization primitive frame used to acquire a valid
AL_PA.
LIPF8F7 A loop initialization primitive frame used to indicate that a
loop failure has been detected at the receiver.
Link Failures Number of optical link failures detected by this port. A link
failure is a loss of synchronization for a period of time
greater than the value of R_T_TOV or by loss of signal
while not in the offline state. A loss of signal causes the
switch to attempt to re-establish the link. If the link is not
re-established by the time specified by R_T_TOV, a link
failure is counted. A link reset is performed after a link
failure.
Login Time when user logged in.
Logout Time when user logged out.
LoopTimeouts A two (2) second timeout as specified by FC-AL-2.
LossOfSync Number of synchronization losses (>100 ms) detected by
this port. A loss of synchronization is detected by receipt of
an invalid transmission word.
PrimSeqErrors Primitive sequence errors detected.
EportConnects Shows the count of the number of times an E_Port
connected through ISL negotiation.
RxLinkResets Number of link reset primitives received from an attached
device.
RxOfflineSeq Number of offline sequences received. An OLS is issued
for link initialization, a Receive & Recognize
Not_Operational (NOS) state, or to enter the offline state.
TotalErrors Total number of errors detected.
TotalLIPsRecvd Number of loop initialization primitive frames received by
this port.
TotalLinkResets Total number of link reset primatives.
TotalOfflineSeq Total number of Offline Sequences issued by this port.
TotalRxFrames Total number of frames received by this port.
TotalRxWords Total number of words received by this port.
TotalTxFrames Total number of frames issued by this port.
Table A-13. Show Port Parameters (Continued)
Entry Description