User`s guide
Table Of Contents
- Table of Contents
- Section1 Introduction
- Section2 Using SANbox Manager
- 2.1 Installing SANbox Manager
- 2.1.1 SANsurfer Management Suite Disk - Windows Installation
- 2.1.2 SANsurfer Management Suite Disk - Linux Installation
- 2.1.3 SANsurfer Management Suite Disk - Solaris Installation
- 2.1.4 SANbox2 Installation Disk - Windows Installation
- 2.1.5 SANbox2 Installation Disk - Linux Installation
- 2.1.6 SANbox2 Installation Disk - Solaris Installation
- 2.2 Starting SANbox Manager
- 2.3 Exiting SANbox Manager
- 2.4 Uninstalling SANbox Manager
- 2.5 Changing Default File Password
- 2.6 Setting Preferences
- 2.7 Using Online Help
- 2.8 Viewing Software Version and Copyright Information
- 2.9 SANbox Manager User Interface
- 2.10 Using the Topology Display
- 2.11 Using the Faceplate Display
- 2.1 Installing SANbox Manager
- Section3 Managing Fabrics
- 3.1 Security
- 3.2 Managing the Fabric Database
- 3.3 Replacing a Failed Switch
- 3.4 Displaying Fabric Information
- 3.5 Zoning a Fabric
- Section4 Managing Switches
- 4.1 Displaying Switch Information
- 4.2 Managing Alarms
- 4.3 Exporting Name Server Information to a File
- 4.4 Paging a Switch
- 4.5 Setting the Date and Time
- 4.6 Setting Temperature Thresholds
- 4.7 Resetting a Switch
- 4.8 Configuring a Switch
- 4.9 Archiving a Switch
- 4.10 Restoring a Switch
- 4.11 Managing Firmware
- 4.12 Restoring the Factory Default Configuration
- Section5 Managing Ports
- AppendixA Command Line Interface
- A.1 Logging On to a Switch
- A.2 Command Syntax
- A.3 Commands
- Admin Command
- Alias Command
- Config Command
- Date Command
- Fallback Command
- Help Command
- History Command
- Image Command
- Lip Command
- Passwd Command
- Ps Command
- Quit Command
- Reset Command
- Set Command
- Set Config Command
- Set Log Command
- Set Port Command
- Set Setup Command
- Show Command
- Show Config Command
- Show Log Command
- Show Perf Command
- Show Setup Command
- Shutdown Command
- Test Command
- Uptime Command
- User Command
- Whoami Command
- Zone Command
- Zoneset Command
- Zoning Command
- AppendixB Graphing Port Performance
- AppendixC Messages
- C.1 Fabrics File—Open, Save
- C.2 Add a Fabric
- C.3 Network Properties Dialog
- C.4 Switch Properties Dialog
- C.5 Port Properties Dialog
- C.6 Faceplate Display
- C.7 Firmware Fallback Dialog
- C.8 Load Firmware Dialog
- C.9 Port Loopback Test Dialog
- C.10 Extended Credits Dialog
- C.11 Zoning Dialog
- C.12 Restore Configuration Dialog
- C.13 Save Fabric View
- C.14 Trap Configuration Dialog
- Glossary
- Index
A – Command Line Interface
Show Command
A-42 59022-05 A
Show Command
Displays fabric, switch, and port operational information.
Authority User
Syntax show
about
alarm
broadcast
chassis
config [option]
domains
donor
fabric
interface
log [option]
lsdb
mem [count]
ns [option]
pagebreak
perf [option]
port [port_number]
post log
setup [option]
steering [domain_id]
support
switch
topology
users
version
Keywords about
Displays an introductory set of information about operational attributes of the
switch. This keyword is equivalent to the Version keyword.
alarm
Displays the last 200 alarm entries.
broadcast
Displays the broadcast tree information and all ports that are currently transmitting
and receiving broadcast frames.
chassis
Displays chassis component status and temperature.
config [option]
Displays switch and port configuration attributes. Refer to the Show Config
Command on page A-54.